Search results

PineNote Development/Building Kernel
2. Make a separate directory for patching the kernel. Then run Maximilian's ' ...the kernel image (called ''Image''), the device tree (''rk3566-pinenote-v1.2.dtb''), and the modules. All of these files have been compiled and placed i

9 KB (1,407 words) - 18:55, 14 April 2023
PinePhone Pro
...IMAGE.bmap''' '''IMAGE.xz''' /dev/'''[DEVICE]'''</code>. This takes around 2.5 minutes to flash a 4 GB file. #: ''└─mmcblk2p2 179:2 0 115.1G 0 part /''

38 KB (6,161 words) - 21:30, 21 December 2023
PineTab
** M.2 SSD slot, supports SATA and USB devices only, not NVME (optional) * '''I/O:''' HD Video Out (Mini HDMI), Micro USB 2.0 OTG, USB 2.0 A host, 3.5mm Headphone/Mic combo,

9 KB (1,373 words) - 09:50, 9 December 2023
PinePhone
* '''Front Camera:''' Single 2MP, f/2.8, 1/5" * [[PinePhone v1.2]] - Ubports Community Edition

44 KB (6,816 words) - 08:32, 26 December 2023
PinePhone Installation Instructions
...IMAGE.bmap''' '''IMAGE.xz''' /dev/'''[DEVICE]'''</code>. This takes around 2.5 minutes to flash a 4 Gb file. (parted) resizepart 2 100%

12 KB (1,957 words) - 14:50, 12 August 2023
Pinebook Pro
...s include the Rockchip RK3399 SoC, USB-C for data, video-out and power-in (2.5 A at 5 V), privacy switches for the microphone, BT/WiFi module, ...by setting an internal switch). The keyboard and touchpad both use the USB 2.0 protocol. The LCD panel uses the eDP MiPi display protocol.

76 KB (11,918 words) - 14:57, 12 January 2024
PinePhone Power Management
| 2.8V | 2.8V

10 KB (1,659 words) - 14:57, 26 April 2021
SOPine GPIO Alternate Functions Table
...asheet/pine64/A64_Datasheet_V1.1.pdf Allwinner A64 Datasheet] section '''4.2 GPIO Multiplexing Functions''' and section '''4.3 Detailed Pin/Signal Descr ...!! SOPine Pin !! Direction !! Default Function !! Default Pull !! Function 2 !! Function 3 !! Function 4 !! Function 5 !! Function 6 !! SOPine Name

13 KB (1,905 words) - 11:22, 1 February 2023
Pinebook Pro Troubleshooting Guide
...rnal magnet is pulled into the proper position. I successfully used four 1/2" cube neodymium magnets stacked on top of each other each having 20lbs of p ...solution is to use 5Ghz WiFi if you can. Or you may try using a different 2.4Ghz channel, perhaps channel 1 or the top channel, (11 in the USA, or 13/1

21 KB (3,454 words) - 14:29, 15 October 2023
Clusterboard
...d rev 2.2.jpg|400px|thumb|right|Front view of the Clusterboard (revision 2.2)]] * Seven USB 2.0 ports, one for each SOPINE module

12 KB (1,868 words) - 05:49, 1 November 2023
PinePhone APN Settings
Name: Internet/MMS 2

15 KB (1,953 words) - 05:27, 14 December 2023
InfiniTime
...bootloader (from InfiniTime 0.7.1), upgraded from InfiniTime 0.7.1 to 0.8.2 and the watch resets while the display is OFF : the watch is stuck on a bla This issue is caused by InfiniTime 0.8.2 that put the external SPI flash memory to sleep before switching the displa

12 KB (1,590 words) - 05:56, 12 August 2023
PineCone
* 2.4 GHz RF transceiver !colspan="2" | Default JTAG pins

14 KB (2,194 words) - 00:59, 11 May 2023
PinePhone Carrier Support
...|| Not tested || Yes || Yes || Mobian Phosh (20210517 image up to date) - 2 June 2021 * Arch Linux Arm - Phosh 0.10.2 2021/05/29

21 KB (3,108 words) - 15:38, 26 December 2023
PinePhone FAQ
The Community Edition program (featuring the mainboard numbers 1.2 through 1.2b and branded back covers) which provided the branded PinePhones ...here has also been minor hardware changes with the UBports CE (mainboard 1.2) and the Manjaro CE (mainboard revision 1.2b).

25 KB (3,908 words) - 03:10, 16 March 2023
Getting started
...er to the PINE64 Single Board Computer. You'll need a good quality 5 Volt, 2 Amp PSU. Using a good quality PSU is very important as failing to meet the ...nux_Upgrade_Tool_to_flash_update.img here]. Make sure that you download v1.2 or newer, as older tools do not support the RK3328 used on the Rock64.

36 KB (6,126 words) - 19:43, 5 August 2023

Search results

Navigation menu

Search