Search results

Jump to navigation Jump to search

Page title matches

Page text matches

  • #REDIRECT [[ROCKPro64 Device Tree Overlays on Mainline]]
    56 bytes (7 words) - 11:51, 10 December 2021
  • ...<code>CONFIG_OF_LIBFDT_OVERLAY</code> (which Manjaro's is), adding device tree overlays the mainline way is very simple and easy. == Writing Your Device Tree Overlay ==
    3 KB (557 words) - 15:00, 29 December 2021
  • ...difying the device tree. The easiest way to go about this is to use device tree overlays. .../kernel.org kernel.org] if you don't already have one. To build the device tree overlays, run <code>make INCLUDE_DIR=path/to/linux/include</code> in the ov
    3 KB (474 words) - 21:58, 2 April 2023
  • ...der to a [[Quartz64]] Model A single-board computer, including what device tree changes to make and how to control it. == Device tree changes ==
    9 KB (1,418 words) - 21:39, 2 April 2023
  • ...an, a slight workaround can be done; with the <code>gpio-fan</code> device tree binding, an Arduino can be controlled to soft-PWM a suitable 25 kHz signal ...or any purpose by anyone. It is recommended to play around with the device tree though, to add more trip points for better control over when the fan actual
    3 KB (592 words) - 21:29, 2 April 2023
  • ...455-sdio.txt from the [https://github.com/LibreELEC/brcmfmac_sdio-firmware/tree/master libreELEC repositories] and place them in the same location as your ...odel A (which uses the same SoC as the Pinenote), we can modify the device tree prior to building the kernel to try to mitigate poor Bluetooth audio stream
    3 KB (419 words) - 15:05, 22 February 2023
  • ...er installed, or an existing aarch64 system. You will also need the device tree compiler dtc, python3 (including setuptools and pyelftools), swig, GNU make apt install device-tree-compiler build-essential gcc-aarch64-linux-gnu binutils-aarch64-linux-gnu m
    3 KB (426 words) - 11:09, 31 August 2023
  • ...your choice. This can be on the same filesystem as your kernel and device tree if using ''extlinux.conf''. ...tree from U-Boot, or mark the partition containing your kernel and device tree with the legacy bootable flag and [https://u-boot.readthedocs.io/en/latest/
    5 KB (736 words) - 15:10, 26 September 2023
  • These displays have free and open-source drivers in the main Linux kernel tree.
    2 KB (214 words) - 21:59, 2 April 2023
  • ...e port can be switched back to gen 2 speeds by adding the following device tree overlay. 1. Copy and paste the device tree overlay file below into a new file (you could name it <code>pcie-2.0.dts</c
    15 KB (1,990 words) - 10:53, 24 October 2023
  • ...v5.12/source/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi#L194 A64 device tree]. The possible names and associated meanings for the trip point types are t
    3 KB (396 words) - 01:50, 16 August 2022
  • # It is now ready to use if your device tree has been set up correctly. For the battery to be correctly detected, you will need to edit the device tree to add the charger and battery nodes, like this:
    5 KB (685 words) - 22:04, 2 April 2023
  • ...al'''. ''On Armbian there is no need for disabling ehci0 and ohci0. Device tree can be edited via armbian-config tool on Armbian OS. (armbian-config -> Sys ...al'''. ''On Armbian there is no need for disabling ehci0 and ohci0. Device tree can be edited via armbian-config tool on Armbian OS. (armbian-config -> Sys
    10 KB (1,452 words) - 10:30, 30 March 2023
  • ...ugs and to improve power management. Therefore, it needs an updated device tree. The state of PL6 at boot can be used to distinguish between v1.1 (it can b ...of 2 devices). Therefore it's not possible to come up with a single device tree brightness settings that will work for everyone, requiring per-device calib
    5 KB (926 words) - 23:44, 24 December 2023
  • ! scope="row" rowspan="4" | Device Tree ...rg/linus/d74d99229f4d48f42d674f7a8a1137179efd67ac]</sup>. Necessary device tree changes [https://patchwork.kernel.org/project/linux-rockchip/list/?series=5
    21 KB (3,171 words) - 14:48, 8 October 2023
  • ...on regarding clock speeds, voltages and more are stored in the DTB (Device Tree Blob). You can learn more about it [https://elinux.org/Device_Tree_Referenc ...DRAM is running at can be found using this command: <code>cat /proc/device-tree/memory/ram_freq</code>}}
    11 KB (1,880 words) - 08:37, 29 November 2023
  • ...More recently, they use [https://en.wikipedia.org/wiki/Device_tree Device tree] but this is also stored in a partition.
    5 KB (777 words) - 04:17, 30 November 2020
  • | driver developed here: <sup>[https://github.com/smaeul/linux/tree/rk35/tps65185]</sup>, small tweaks to resume behavior added on top here: <s ...github.com/smaeul/linux/commits/rk356x-ebc-dev. This has a complete device tree, with working eMMC. Pen input also works out of the box. Wi-Fi and BT work
    11 KB (1,638 words) - 23:34, 7 April 2023
  • ...lt between v1.1 and v1.2. Reading the pin in SPL will tell us which device tree to use. ...r control and rear camera reset GPIOs at PD2/PD3. This would need a device tree change.
    14 KB (2,411 words) - 15:20, 27 February 2023
  • Kernel 5.18 and 5.19 do not yet have the Quartz64 Model B device tree, however, you can add it manually to your install and adjust <tt>extlinux.c
    4 KB (710 words) - 19:02, 20 February 2023

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)