Difference between revisions of "Pinebook Pro Software Release"

From PINE64
Jump to navigation Jump to search
m (Updating HTML code to markdown)
(Debian: added changes to reflect the updated hardware in the June/July 2022 PBP batch)
 
(One intermediate revision by one other user not shown)
Line 8: Line 8:
All images boot from both SD card and the internal eMMC module.
All images boot from both SD card and the internal eMMC module.


=== Manjaro ARM with KDE Plasma ===
[https://manjaro.org/download/ Direct download from Manjaro]: You have to navigate to the Manjaro ARM Team section and select Pinebook Pro as the device in the drop-down list. Then you can choose Gnome, KDE Plasma, Mate, Minimal, Sway or Xfce.
 
* [https://manjaro.org/downloads/arm/pinebook-pro/arm8-pinebook-pro-kde-plasma/ Direct download from Manjaro]
 
=== Manjaro ARM with Xfce ===
 
* [https://manjaro.org/downloads/arm/pinebook-pro/arm8-pinebook-pro-xfce/ Direct download from Manjaro]
 
=== Manjaro ARM with Gnome ===
 
* [https://manjaro.org/downloads/arm/pinebook-pro/arm8-pinebook-pro-gnome/ Direct download from Manjaro]
 
=== Manjaro ARM with Sway ===
* [https://manjaro.org/downloads/arm/pinebook-pro/arm8-pinebook-pro-sway/ Direct download from Manjaro]
 
=== Manjaro ARM with no desktop ===
* [https://manjaro.org/downloads/arm/pinebook-pro/arm8-pinebook-pro-minimal/ Direct download from Manjaro]


== Armbian ==
== Armbian ==
Line 308: Line 292:
* Uses only the upstream kernel and firmware without special patches
* Uses only the upstream kernel and firmware without special patches
* Display doesn't always work properly on first boot of installer, usually fixed after a couple tries
* Display doesn't always work properly on first boot of installer, usually fixed after a couple tries
* Requires adding the non-free component to your /etc/apt/sources.list file and installing the "firmware-linux" package for Wi-Fi and Bluetooth support
* Requires adding the non-free component to your /etc/apt/sources.list file and installing the "firmware-linux" package for Wi-Fi and Bluetooth support. If your Pinebook Pro was part of the June/July 2022 batch, then you will need the "firmware-brcm80211" to accommodate the changed networking hardware. You will also need "brcmfmac43455-sdio.txt" in /lib/firmware/brcm, at least until it is included within firmware-brcm80211 upstream.
* Installer is loaded into RAM, can install onto the same media from which it’s booted
* Installer is loaded into RAM, can install onto the same media from which it’s booted
* Supports automatic partitioning and full disk encryption through LVM
* Supports automatic partitioning and full disk encryption through LVM

Latest revision as of 04:34, 9 August 2022

Linux OS Image Releases

For information on how to install these images onto your device, please see the NOOB Page, which includes information on writing images to the device eMMC or an SD card

Manjaro ARM

Manjaro.png

The Manjaro project offers a mainline kernel with patches and modules to support PBPro hardware. To learn more about Manjaro please visit Manjaro Forum. You can follow the ongoing discussion about Manjaro on the PINE64 forum. All images boot from both SD card and the internal eMMC module.

Direct download from Manjaro: You have to navigate to the Manjaro ARM Team section and select Pinebook Pro as the device in the drop-down list. Then you can choose Gnome, KDE Plasma, Mate, Minimal, Sway or Xfce.

Armbian

Armbian is a base operating system platform for single board computers (SBCs) that other projects can trust to build upon.

  • Lightweight Debian or Ubuntu based Linux distribution specialized for ARM development boards
  • Each system is compiled, assembled and optimized by Armbian Build Tools
  • It has powerful build and software development tools to make custom builds
  • A vibrant community
Armbian.png

To download the latest Armbian Desktop or CLI images for Pinebook Pro, please visit The Pinebook Pro Download Page.

If you have any difficulties please visit our forum or come chat with us on IRC / Discord!

Twister OS

Twister OS.png

Twister OS Armbian-Reforged with Xfce. It boots from microSD card and from eMMC. For more information on Twister OS, please visit this official site. You can follow the ongoing discussion about Twister OS on the PINE64 forum.

Installation

  • After flashing image, edit /boot/armbianEnv.txt, replace the dtb name with rk3399-pinebook-pro.dtb

Download location

Get the latest image here: Direct download latest images from Twister OS's website (size: 2.8GB)

Password

asdasd

Fedora

Fedora1.png

Fedora Official

Using this blog post it is now possible to run Official Fedora on the Pinebook Pro.

Notes Upstream Fedora uses SPI flash on the Pinebook Pro to manage uboot.

Fedora 32 with Cinnamon

This image contains an install of Fedora with Cinnamon desktop environment. It boots from microSD card and from eMMC. To learn more about Fedora please visit the official website.

Download location

Get the latest image here: Fedora 32 Pinebook Pro Image

Username and password

root/fedora

Fedora 32 with KDE

This image contains an install of Fedora with KDE aka Plasma desktop environment. It boots from microSD card and from eMMC. To learn more about Fedora please visit the official website.

Download location

Get the latest image here: Fedora 32 Pinebook Pro Image

Username and password

root/fedora

Fedora 32 with Xfce

This image contains an install of Fedora with Xfce desktop environment. It boots from microSD card and from eMMC. To learn more about Fedora please visit the official website.

Download location

Get the latest image here: Fedora 32 Pinebook Pro Image

Username and password

root/fedora

Fedora 32 with Gnome

This image contains an install of Fedora with GNOME 3 desktop environment. It boots from microSD card and from eMMC. To learn more about Fedora please visit the official website.

Download location

Get the latest image here: Fedora 32 Pinebook Pro Image

Username and password

root/fedora

Arch Linux ARM

Archlinux-logo.png

Official Installation

See Installing Arch Linux ARM On The Pinebook Pro for instructions on how to install the official Arch Linux ARM.

Customized Premade Image

Arch Linux ARM root filesystem customized for the Pinebook Pro using Manjaro kernel. Instructions are included for installation on microSD card, eMMC module and NVME SSD.

Download location

Get the latest image from GitHub (size: 591 MB).

Installation

Make sure to thoroughly read the readme, installation instructions and FAQ.

Username and password

The default Arch Linux ARM user credentials.

Username: alarm

Password: alarm

The password for the root account is 'root'.

postmarketOS

PostmarketOS logo.png

Official postmarketOS stable builds are available for the Pinebook Pro with the following interfaces:

  • console
  • GNOME
  • KDE Plasma Desktop
  • Phosh
  • Sway

It boots from microSD card and from eMMC.

Download location

Get the stable image here: https://postmarketos.org/download/ (size: 103 MB to 775 MB)

The installer images allows setting up an encrypted installation on SD or eMMC.

Username and password

user/147147

Kali Linux

Kali.jpeg

Kali Linux prebuilt OS images for Pinebook Pro

Official pre-built OS images of Kali Linux for the Pinebook Pro featuring all tools you'd expect from the distribution. It boots from microSD card and from eMMC.

Download location

Get the latest image here: Direct download latest images from Offensive Security's website (size: 2.0 GB)

Username and password

kali/kali

Q4OS

Q4os.png

Q4OS is advertised as a 'fast and powerful operating system based on the latest technologies while offering highly productive desktop environment'. It boots from microSD card and from eMMC. To learn more please visit the PINE64 forum or official Q4OS website.

Download location

Get the latest image here: Direct download latest release build from SourceForge

Username and password

User account and password are created on first run.

DietPi

Dietpi.png

openSUSE

Opensuse-distribution.png

Download location

Get the latest openSUSE Tumbleweed images for Pinebook Pro here: [1]

Credits to [2] Step 1. Flash Tow-Boot[3] to SPI Step 2. Flash openSUSE image to sd card & insert it Step 3. When it loads grub, press e and add the following line:

devicetree /boot/dtb/rockchip/rk3399-pinebook-pro.dtb

Press ctrl + x to boot

Work : display, wifi Not tested : bluetooth Doesn't work : audio

You may build rpms and see if it fix issues from this repository: [4]

FydeOS

An operating system based on the Chromium Project

https://fydeos.io/download/device/pinebook-pro

Void Linux

Void Linux packages U-Boot and a kernel for the Pinebook Pro, but does not distribute any images for the device.

Cameron Nemo (User:CameronNemo) distributes unofficial Void Linux images for the Pinebook Pro:

Some notes about the images:

  • They were released on 2022-05-30 (glibc) and 2022-06-10 (musl)
  • They ship U-Boot 2022.04 and Linux 5.15 (with minimal patches)
  • Meant to be uncompressed then flashed to either an SD card or the internal eMMC module
  • The root partition is ~1.7GB, and must be expanded manually
  • There are very few services enabled on the images by default: udev and some getty's
  • The default root password is "voidlinux"

BSD

NetBSD

Netbsd.png

The image boots from microSD card and from eMMC. To learn more about NetBSD please visit NetBSD main page

Download location

Get the latest image here: Direct download from NetBSD

Installation

Instructions concerning enabling SSH can be found here.

Username and password

root/(none)

OpenBSD

Puffy mascot openbsd.png

The image boots from microSD card and from eMMC. To learn more about OpenBSD, please visit OpenBSD main page

Download location

ARM64 images, (including support for Pinebook Pro), can be found here OpenBSD arm64

Linux Installer Releases

Manjaro ARM

Manjaro.png

The manjaro-arm-installer script is intended to install Manjaro ARM directly to SD/eMMC cards without the need for images (including LXQT, Mate & CuboCore editions, as well as full disk encryption).

Running on a Linux x86 computer, it can install Manjaro ARM directly to an empty eMMC using an eMMC to USB adapter. The script can also be run from SD to install an image to the eMMC.

Armbian

Armbian.png

You can use the Armbian Builder to generate your own Armbian images of various types.

The builder supports building any version of Debian and any version of Ubuntu with various desktop options:

  • Budgie
  • Cinnamon
  • Deepin
  • Enlightenment
  • Gnome
  • I3-wm
  • Kde-plasma
  • Mate
  • Xfce
  • Xmonad

    Debian

    Debian.png
    • Uses only the upstream kernel and firmware without special patches
    • Display doesn't always work properly on first boot of installer, usually fixed after a couple tries
    • Requires adding the non-free component to your /etc/apt/sources.list file and installing the "firmware-linux" package for Wi-Fi and Bluetooth support. If your Pinebook Pro was part of the June/July 2022 batch, then you will need the "firmware-brcm80211" to accommodate the changed networking hardware. You will also need "brcmfmac43455-sdio.txt" in /lib/firmware/brcm, at least until it is included within firmware-brcm80211 upstream.
    • Installer is loaded into RAM, can install onto the same media from which it’s booted
    • Supports automatic partitioning and full disk encryption through LVM
    • Installer currently doesn't install a functional bootloader, leaving the installed system in an unbootable state until it's manually added (if installed to eMMC, the system cannot be booted even to an SD card unless the eMMC is physically switched off or there is U-Boot in the SPI)

    The relevant files are built daily here and may sometimes be unavailable if the build system is having issues. The "README.concatenateable_images" file provides instructions on how to combine the partition.img.gz file with the firmware.pinebook-pro.rk3399.img.gz file in order to create a DD-able image.

    The official images are not recommended yet until the display begins working consistently and the installer properly installs the bootloader. Most users will want to see Daniel Thompson's Debian Installer instead.

    Gentoo

    GentooLogo.png

    There is a script that prepares a Gentoo arm64 stage 3 tarball for the Pinebook Pro. Unfortunately, this script is not currently functional, and requires extensive troubleshooting to make work. New instructions are currently being created and will be available here.


    Word to the wise

    Currently, following the instructions on the Pinebook pro gentoo github page will *not* result in a functional system. Therefore it is neccesary to follow the instructions given here. Please bear in mind that the Pinebook pro's six arm cores and 4gb of ram are extremely anemic. For example, emerging the package net-libs/webkit-gtk in order to build the minimalist web-browser "surf", a process which takes eighty minutes on an intel core i5-8250U with 8gb of ram, required eight hours of compile time, Basic installation alone can take 24 hours of compillation, dozens of reboots, and hours of troubleshooting. After that, even installing firefox would take 17 hours. Now that that's out of the way, we may begin the installation.

    Preparing the bootloader

    Installing a functional bootloader can be difficult. Luckily, the tow-boot project provides a UEFI-like experience for some arm-based devices. Furthermore, it is not neccesary install this bootloader manually, as it will continue to be useable even after the disk has been reformatted, as long as the bootloader remains unscathed.

    https://manjaro.org/downloads/arm/pinebook-pro/arm8-pinebook-pro-minimal/

    No-matter where you intend to install gentoo, the bootloader should always be installed on the eMMC flash, although technically the SD card slot could also be used. Either way, install any of the official Manjaro arm disk images to the internal eMMC (there's no reason not to use the minimal image, as you will not be using this OS for anything). You may use a second operating system installed on an SD-card, or the official Pine64 eMMC USB adapter. Boot into this operating system to ensure that the bootloader functions, but after that you have no further need of it.

    Next, if you already have an OS on an SD card, you can use that for installing gentoo. If you don't, you may be pleasantly suprised to find that tow-boot is cabable of booting from a USB drive. Therefore, you may install the same Manjaro image to your USB drive or SD card, and select it from the boot menu. You should now have an unused but bootable OS on the eMMC, and another bootable, usable OS on your external storage.

    Preparing the Disks

    Log into your host device as root with the following command:

    sudo su

    Enter your password.

    Let the device on which you intend to install gentoo be refered to hereafter as /dev/<gentoo>. Use the following command to prepare this disk for installation:

    fdisk -B /dev/<gentoo>

    Note: don't just copy these commands! You should substitute <gentoo> for mmcblk2 for the internal eMMC flash storage.

    Note that the first block of the boot partition is block 62500. Delete all partitions, but *do not* re-format the disk. Create a new boot partition starting at 62500, and as it's size select "+1GB". Create a new swap partition. fdisk will try to start it at the beginning of the volume (before the boot partition) Instead, when it prompts you for the starting position, enter in the end sector of the boot partition. It should then tell you that this is within an existing partition, and recommend a slightly higher value. Press enter, and give for the size of the partition any value greater than "+4gb". You need this much ram to be able to suspend your system, and emerge large packages. Don't be stingey - you still have SD cards. I reccomend "+8gb". Finally, add a root partition starting at the end sector of the swap partition, and use the rest of the disk for it. That should be 50-60 GB depending on the size of your swap and boot partitions.

    Lastly, press "t" to set the type of each partition. You may set partition 1 to type 6, 2 to type 82, and 3 to type 83.

    to set the partition types of the three partitions.

    lsblk

    to remind yourself which disk is /dev/<gentoo> Write the filesystems to these three partitions with the commands:

    mkfs.vfat /dev/<gentoo>p1

    mkswap /dev/<gentoo>p2

    mkfs.ext4 /dev/<gentoo>p3


    This may be a slightly different format if you're installing to a usb stick.

    Installation

    make the directory for mounting the filesystem you just created. These should be made on the external OS.

    mkdir /mnt/gentoo

    mount /dev/<gentoo>p3 /mnt/gentoo

    cd into this directory and fire up links. Navigate to gentoo.org/downloads and select the stage 3 minimal stage 3 tarball. Download it to your current directory, or move it to that directory from wherever it has been downloaded to. Once you are in the correct directory, unpack the tarball.

    tar xpvf stage3-arm64-<blah blah blah>

    Mount the boot partition.

    mount /dev/<gentoo>p1 /mnt/gentoo/boot


    Chroot into the mounted directory and Install the operating system as per the AMD64 manual [5]. Before you emerge anything, however, be sure to set your use flags as follows:

    nano /etc/portage/make.conf


    MAKEOPTS="-j4 -l4"

    ACCEPT_KEYWORDS="* **"

    ACCEPT_LICENSE="*"

    USE="X gtk bluetooth pulseaudio"

    You can use your own options instead of these if you know what you're doing. It's not super difficult.

    Continue installing the operating system, but stop just before emerging the @world set. I don't know if this is necessary, but I haven't had the time to try without doing this. Clone Janikk2099's github repo. It doesn't matter where, and run the script. If it fails run it a couple more times.

    git clone https://github.com/Jannik2099/gentoo-pinebookpro

    ./gentoo-pinebookpro/prepare.sh

    Don't follow any of Janikk's other instructions. They appear to be out of date (no offense bro). Let me be clear: DO NOT INSTALL U-BOOT. I don't know what will happen, but it won't be an improvement over the existing boot-loader so don't worry about it.

    Finish installing your system until you come to the kernel.

    Custom Kernel

    Use sys-kernel/gentoo-kernel-bin as your kernel. You will need to manually edit the kernel configuration. First, select it as your kernel.

    eselect kernel list

    This should list only one option. Otherwise, select the number matching linux-5.<whatever is latest>-gentoo-dist, and cd into the kernel source directory.

    eselect kernel set <number>

    cd /usr/src/linux

    Begin the kernel configuration

    make menuconfig

    At this point, you're almost on your own. I don't know a strict cause-and-effect relationship between my kernel config and the behavior of my system. For starters, just go into platform selection and deselect everything except rockchip platforms. Once you're done save your configuration and exit. Make sure boot is mounted, and your fstab is set up with your swap mounted. Make sure dracut is installed.

    make

    make modules

    make dtbs

    make install

    make modules install

    make dtbs_install

    ls /lib/modules

    dracut -f --kver <name of directory in /lib/modules matching your kernel, *not* the kernel name from eselect>

    emerge the package extlinux and run u-boot-update. Open the extlinux configuration file.

    nano /boot/extlinux/extlinux.conf

    And configure it as follows:

    LABEL <label of your choice, for example GENTOO ARM>

    KERNEL /<name of your vmlinuz kernel image. Include the slash, but be relative to boot, not root.>

    FDT /dtbs/<kernel-version>/rockchip/rk3399-pinebook-pro.dtb

    APPEND initrd=/<name of initramfs image> root=PARTUUID-<nboot partition's PARTUUID, no quotes> rw rootwait

    You can use the blkid command to find the PARTUUID of every partition on the machine. None of this configuration is guaranteed to work, but it worked for me, and given enough fiddling you can get it to work as well.

    Now you should reboot the machine and see if it boots into gentoo. If it does: congratulations! If not, too bad. Try again.

    Kali Linux

    Kali.jpeg

    There is a script to create official Kali Linux OS images for the Pinebook Pro. The script carries out the build process in entirety and is Pinebook Pro specific.

    Installation

    K1ss OS

    K1ss.png

    There is a repository containing an unofficial port of KISS Linux to AARCH64. The tarball is built for generic aarch64, currently being tested on the Pinebook Pro. You can follow the ongoing discussion about K1ss Linux on the PINE64 forum.

    Installation

    NixOS

    Nixos.png

    You can follow the ongoing discussion about NixOS on the PINE64 forum. There is a good chance we will see Tier 1 support for aarch64, including the Pinebook Pro, in 2021 (see https://github.com/NixOS/rfcs/pull/87).

    Installation

    SkiffOS

    SkiffOS-Icon-1.png

    Installation

    • Instructions to build/install on the Pinebook Pro: https://github.com/skiffos/SkiffOS/tree/master/configs/pine64/book
    • Please pull the latest version from the project's GitHub.
    • Compiling the boot image takes approximately 30 minutes.
    • Easily configure the kernel, compiler, etc with Buildroot.
    • Pre-built ISOs will be available with the upcoming 2021.02 release.

    Slackware

    Slackware.jpg

    Slackware is the world's oldest actively developed Linux distribution, providing a modern user land (applications) and Linux Kernel, within a more classic Unix Operating System environment.

    More information can be found about Slackware in this 20 minute video.

    Installation instructions.

    Installation guide video