PinePhone

The PinePhone is a smartphone created by Pine64, capable of running mainline Linux and supported by many partner projects. A "braveheart" edition is currently available for purchase from the PINE64 store, though it should be noted that this version comes without a preinstalled OS, and is geared specifically towards tinkerers and hackers. People looking for a stable consumer-grade phone should wait for the final release, which is expected to occur in March 2020 and will be available for at least five years.

Specifications

Dimensions: 160.5 x 76.6 x 9.2mm
Weight: Between 180-200 grams
Build: Plastic
SIM Card: Micro-SIM
Display:

Size: 5.95 inches (151mm) diagonal

Type: HD IPS capacitive touchscreen, 16M colors

Resolution: 1440x720, 18:9 ratio

System on Chip: Allwinner A64
RAM: 2GB LPDDR3 SDRAM
Internal Storage: 16GB eMMC, extendable up to 2TB via microSD, supports SDHC and SDXC
Back Camera: Single 5MP, 1/4", LED Flash
Selfie Camera: Single 2MP, f/2.8, 1/5"
Sound: Loudspeaker, 3.5mm jack & mic (jack doubles as hardware UART if killswitch 6 is deactivated)
Communication: EG25-G

LTE: B1, B2, B3, B4, B5, B7, B8, B12, B13, B18, B19, B20, B25, B26, B28, B38, B39, B40, B41

WCDMA: B1, B2, B4, B5, B6, B8, B19

GSM: 850, 900, 1800, 1900 (MHz)

WLAN: Wi-Fi 802.11 b/g/n, single-band, hotspot

Bluetooth: 4.0, A2DP

GNSS: GPS/GLONASS/BeiDou/Galileo/QZSS, with A-GPS

Sensors: Accelerometer, gyro, proximity, ambient light, compass
Killswitches: Modem, Wifi & Bluetooth, Microphone, Cameras
Battery: 2750-3000 mAh Lithium ion (replaceable with any Samsung J7 form-factor battery)
I/O: USB Type-C (SlimPort), USB Host, DisplayPort Alternate Mode output, 15W 5V 3A Quick Charge, follows USB PD specification

History

The PinePhone was announced at FOSDEM 2019, February 2-4, 2019. The first Project Don't be evil devkit was on display at the Pine64 booth during the weekend.

Hardware revisions

The PinePhone platform went through two "developer kit" phases that partner projects used to prove their software on the upcoming platform.

1. Project Anakin
2. Project Don't be evil

Additionally, two "early adopter" revisions of the platform were created:

1. PinePhone 1.0 "Developer"
2. PinePhone 1.1 "Brave Heart"

The first generally available PinePhone batch was PinePhone 1.1 "Brave Heart". Pre-orders for this batch started on November 15, 2019. It is expected to ship sometime in December 2019 to January 2020.

A "full release" Pinephone, which will likely have board revision 1.2, will be released in 2020.

Killswitch configuration

The PinePhone features six switches that can be used to configure its hardware. They are numbered 1-6, with switch 1 located nearest to the modem. Their on position is toward the top of the phone.

Photo of Developer mainboard courtesy of Martijn Braam, postmarketOS

1. Modem: On enables 2G/3G/4G communication and GNSS hardware, off disables.
2. WiFi/BT: On enables Wi-Fi and Bluetooth communication hardware, off disables.
3. Microphone: On enables audio input from on-board microphones (not 3.5mm jack), off disables.
4. Rear camera: On enables the rear camera, off disables.
5. Front camera: On enables the front camera, off disables.
6. Headphone: On enables audio input and output via the 3.5mm audio jack, off switches the jack to hardware UART mode.

Modem and Carrier Support

To check if the PinePhone is supported on your carrier:

Search for your carrier on frequencycheck.com and compare the carrier's LTE/GSM/WCDMA frequencies to the PinePhone's supported frequencies (listed under the specifications section).

It is likely that there will be a few frequencies that your carrier uses which are not supported by the PinePhone. Not all of the carrier's frequencies need to be supported by the PinePhone for it to work - as long as most of them are supported, you will still get good coverage.

Software Support

Please see the PinePhoneOS page for details of images available for the PinePhone and how to install them.