Quartz64 Model A Using a battery

The Quartz64 Model A allows for it to be powered from a single-cell 3.7V lithium-polymer battery. Because of unfortunate incidents, batteries are not easy to ship internationally, so PINE Store does not sell a matching battery for the board.

Pin-out

The pins on the board are a JST PH-3 compatible header labelled +VBAT-. As one might guess, the positive wire should be towards the +, and the ground wire towards -. The center pin of the connector is for a temperature probe.

Ways to get a battery

We will now go into various ways one might go about getting a working battery.

Crimping one yourself

You will need:

• an Engineer PA-20 (Amazon Search, eBay Search) or Hozan P-707 (Amazon Search, eBay Search) or similar crimp tool (<$80, good to have around anyway)
  • The Hozan P-707 is also comparatively good at crimping "Dupont"-style terminals, in case you find yourself doing that a lot, because it provides round crimping holes in addition to rectangular ones.
• JST PHR-3 receptacles (~$0.05 on digikey)
• 3× JST SPH-002T-P0.5L crimp terminals (~$0.03 on digikey per terminal)
  • When ordering from digikey, try to hit the minimum order cost to qualify for free shipping; you'll get free fast courier shipping with all customs and duties pre-paid.
• a single-cell 3.7V lithium-polymer battery, ideally with a temperature probe
  • 2800 mAh Renata ICP606168PRT on Conrad Germany, Conrad Switzerland
  • 2000 mAh Adafruit on Adafruit US (no temperature probe, pre-crimped with JST PHR-2; just lift up the plastic tabs and pull out the terminals and shove them back into a PHR-3 connector)
  • Aliexpress: try keywords "3.7v lithium battery temperature probe"

Crimp the terminals onto the wires, crimp the strain relief onto the insulation, slide them into the connector until they firmly click in place.

PINE64 18650 battery case

You will need:

• PINE64 Lithium Battery Casing
• an 18650 sized lithium battery (not LiFePo4!)

TODO: Get one of these and document how to use them

Using the battery

Hardware

1. Ensure the wires in the connector are in the right order.
2. Turn off your Quartz64 Model A.
3. Remove the BAT ON/OFF jumper.
4. Plug in your battery.
5. It is now ready to use if your device tree has been set up correctly.

Caveats

Not all parts of the board can be supplied from the battery. When you use battery as backup power for the board keep in mind that following parts of Quartz64-A will lose power when DCIN loses power:

• 12V Fan connector
• EDP LCD backlight
• 5V power rails on the 20 pin GPIO header
• PCIe socket (both 12V and 3.3V supplies)
• All USB ports except for the black one
• Black USB port's VBUS (the one above the USB 3.0 port) will go through a 22ms brownout to approximately VCC_SYS - 0.6V voltage, before the RK817 BOOST regulator kicks in. This will likely cause the connected USB device to reset or have its internal state corrupted.

Software

Device-Tree Additions

For the battery to be correctly detected, you will need to edit the device tree to add the charger and battery nodes, like this:

	// add this to root node (you may need to modify the values to fit your chosen battery)
	battery: battery {
		compatible = "simple-battery";
		charge-full-design-microamp-hours = <6400000>;
		charge-term-current-microamp = <200000>;
		constant-charge-current-max-microamp = <2000000>;
		constant-charge-voltage-max-microvolt = <4200000>;
		factory-internal-resistance-micro-ohms = <117000>;
		voltage-max-design-microvolt = <4200000>;
		voltage-min-design-microvolt = <3200000>;

		ocv-capacity-celsius = <20>;
		ocv-capacity-table-0 =  <4200000 100>, <4054000 95>, <3984000 90>, <3926000 85>,
					<3874000 80>, <3826000 75>, <3783000 70>, <3746000 65>,
					<3714000 60>, <3683000 55>, <3650000 50>, <3628000 45>,
					<3612000 40>, <3600000 35>, <3587000 30>, <3571000 25>,
					<3552000 20>, <3525000 15>, <3492000 10>, <3446000 5>,
					<3400000 0>;
	};

	// add this to &rk817 node
	rk817_charger: charger {
		monitored-battery = <&battery>;
		rockchip,resistor-sense-micro-ohms = <10000>;
		rockchip,sleep-enter-current-microamp = <300000>;
		rockchip,sleep-filter-current-microamp = <100000>;
	};

You will also need to make sure that CONFIG_CHARGER_RK817 is enabled in your kernel.

Device-Tree Overlay

On some Linux distributions it may be possible to add the device-tree additions via an overlay, example given for the Renata 2800 mAh battery mentioned above:

/dts-v1/;
/plugin/;

/ {
    compatible = "pine64,quartz64-a", "rockchip,rk3566";

    // add this to root node (you may need to modify the values to fit your chosen battery)
    // Values for Renata 2800 mAh ICP606168PRT
    fragment@0 {
        target-path = "/";
        __overlay__ {
            battery: battery {
                compatible = "simple-battery";
                charge-full-design-microamp-hours = <2800000>;
                charge-term-current-microamp = <150000>;
                constant-charge-current-max-microamp = <1400000>;
                constant-charge-voltage-max-microvolt = <4200000>;
                factory-internal-resistance-micro-ohms = <200000>;
                voltage-max-design-microvolt = <4200000>;
                voltage-min-design-microvolt = <3200000>;
            
                ocv-capacity-celsius = <20>;
                ocv-capacity-table-0 =  <4200000 100>, <4054000 95>, <3984000 90>, <3926000 85>,
                    <3874000 80>, <3826000 75>, <3783000 70>, <3746000 65>,
                    <3714000 60>, <3683000 55>, <3650000 50>, <3628000 45>,
                    <3612000 40>, <3600000 35>, <3587000 30>, <3571000 25>,
                    <3552000 20>, <3525000 15>, <3492000 10>, <3446000 5>,
                    <3400000 0>;
            };
        };
    };

    // add this to &rk817 node
    fragment@1 {
        target = <&rk817>;
        __overlay__ {
            rk817_charger: charger {
                monitored-battery = <&battery>;
                rockchip,resistor-sense-micro-ohms = <10000>;
                rockchip,sleep-enter-current-microamp = <300000>;
                rockchip,sleep-filter-current-microamp = <100000>;
            };
        };
    };
};

Battery Parameter Limitations

• the hardware limits the possible max. charge current to the discrete values 0.5A, 1.0A, 1.5A, 2.0A, 2.5A, 2.75A, 3.0A or 3.5A. The kernel driver will therefore use the largest value smaller or equal the configured value.

Device Driver Limitations

• up to kernel version 6.11.2 the value of the temperature sensor is not exposed by the device driver

Recovering the PCIe-Slot after Power Cycling

As mentioned above the PCIe-slot is no longer powered when running on battery. The question is then: how to recover the PCIe-controller after power cycling such that a plugged in extension card (e.g. a SATA controller of whatever) is operational again. One use case is kind of a low-power mode, a NAS system with a decent number of hard-disks may consume about 40W-50W even when idle, while the Quartz64 running from battery consumes less than 2W (when idle).

Soft Reset and Rescan (not working)

Unfortunately, the following does not work:

echo 1 > /sys/bus/pci/devices/0000:00:00.0/remove
# turn power off, wait, turn power on
sleep 5 # or whatever periode
echo 1 > /sys/bus/pci/rescan

The PCIe-slot is then "back again" but not quite. The attached extension card is not reinitialized, and also an additional

echo 1 > /sys/bus/pci/devices/0000:00:00.0/rescan

does not change improve the situation. Without power cycle the above mentioned lines actually do work.

Basic Idea

However, some device drivers in Linux can be compiled as loadable modules which can be removed and reloaded again. The hope was that the device driver for the DW PCIe-controller does some reinitialization during the boot sequence which it does not when a mere "rescan" request is issued. If the device driver existed as loadable module then removing the driver and reloading it should in some sense simulate the boot initialization.

Kernel Patch

Unfortunately, the device driver drivers/pci/controller/dwc/pcie-dw-rockchip.c has not been designed as loadable module (as of Linux 6.11.3), but the necessary changes are only few. The following source-code patch will add the loadable module feature:

Media:Kernel-rockchip64-pcie-dwc-module.tar

(sorry for wrapping it into a tar archive, but .patch files are not allowed)

Of course, in order to use that you have to know how to apply patches to source code and how to recompile the kernel. It is beyond the scope of this Wiki page to elaborate on this.

Using the pachted Device Driver

After applying the patch, reconfiguring the kernel to use the PCIe driver as a module and recompiling and installing the kernel one is almost done.

Disengaging the PCIe slot prior to power cycling:

# turn off anything using the PCIe extension card, unmount drives etc. then:
echo 1 > /sys/bus/pci/devices/0000:00:00.0/remove
rmmod pcie_dw_rockchip

Then switch off the 12V main power supply. The PCIe slot will then remain unpowered as mentioned above. In order to recover the PCIe slot and an attached extension card one has -- of course -- to switch on the main power supply and can then proceed as follows:

# wait some seconds after reattaching the main power supply
modprobe pcie_dw_rockchip

Afterwards there chances that the PCIe bus has been reinitialized and works as before.

Specific Linux Distributions

Armbian

Device Tree Additions

Save the DTB-overlay snippet above to a file, e.g. "battery.dts" and then use

sudo /usr/sbin/armbian-add-overlay battery.dts

in order to compile and add the overlay to "/boot/armbianEnv.txt".

Patching the Kernel

When using the Armbian build system, see https://github.com/armbian/build, it is possible to apply custom "user" patches by placing the patch file in userpatches/kernel/archive/KERNEL_NAME_AND_VERSION/PATCHFILE. For the example of using Ubunut "Noble" and trying to apply above mentioned patch to turn the PCIe driver into a loadable module this would be

userpatches/kernel/archive/rockchip64-6.6/kernel-rockchip64-pcie-dwc-module.patch

Afterwards, it is possible to reconfigure and recompile the kernel using the commands:

# after a while, the following will show the configuration menu
# go to "Device Drivers" -> "PCI Support" -> "PCI Controller Drivers" -> "DesignWare-based PCIe controllers"
# and configure "Rockchip DesignWare PCIe controller" to be built as module
./compile.sh  BOARD=quartz64a BRANCH=current kernel-config
# recompile the kernel
./compile.sh  BOARD=quartz64a BRANCH=current kernel
# recompile uboot (needed?)
./compile.sh  BOARD=quartz64a BRANCH=current uboot

The resulting .deb packages can be found in output/debs/, copy them to your running Quartz64 system and install them and reboot. On reboot the pcie_dw_rockchip module should be loaded automatically