Search results
Jump to navigation
Jump to search
- ...a lot of experience and thought put into the system already, and it would be good to leverage that for other projects as well, once they are ready to lo As I think it would be sad to leave such valuable info in the backlog of the chat, I would like to9 KB (1,488 words) - 18:34, 4 April 2023
- ...will also need libncurses.so.5. The easiest way to install this appears to be using an Arch AUR package. For QUARTZ64-model-A_eink.android11_SDK the following files will need to be updated:-2 KB (340 words) - 16:45, 20 February 2023
- # Requires confirmation: [[Project Don't be evil|"Project Don't Be Evil" devkit]] ...-marked" and "managed active cables"); they contain a chip, which needs to be powered. This is done by having one of the cable end connect its CC pins to5 KB (747 words) - 07:39, 17 March 2023
- The GitHub page can be found here: [https://github.com/dreemurrs-embedded/Pine64-Arch/ dreemurrs-e ...er and the desired desktop environment. The ARM64 version of Gentoo has to be selected. The PinePhone Pro will not boot with P-Boot but will boot with U-11 KB (1,617 words) - 09:57, 9 December 2023
- ...isplay, portraying the output voltage and amps. The display back light can be turned on and off by capacitive touch button, located on the top left side ...at can be disconnected from the main PCB. The wireless charging PCB has to be de-soldered, or forcefully removed from the inner casing, as it is glued to6 KB (910 words) - 21:33, 26 July 2023
- # Ordering 2-3 might be a good idea in case the first one is damaged during install (if all goes we ...dymium magnets], just two 8x2.7mm at 8:00PM and 12:00PM on the stand could be enough. Experimentation is needed. Start with just one small magnet and inc5 KB (801 words) - 22:13, 18 June 2023
- Flashing can be done with any of All the zips you need can be found from the [https://wasp-os.readthedocs.io/en/latest/install.html#binar4 KB (654 words) - 14:42, 15 November 2022
- ...sensor coordinate systems into body coordinates, 'mount matrices' have to be defined. accel_x: (input, index: 0, format: be:S16/16>>0)8 KB (861 words) - 16:41, 20 February 2023
- The installation instructions can be found under [[PineTab2#Installation instructions]]. The PineTab2 ships with ''Danctnix Arch Linux ARM''. The factory image can be found here:8 KB (1,162 words) - 10:26, 3 September 2023
- ...Pro64]] single-board computer from an ATX power supply allows the board to be powered with more than just two disks, and is a reliable and safe way to po ...ts have been made to write reliable, safe instructions, the authors cannot be held liable for the quality of procured components or the assembly job of t3 KB (449 words) - 16:42, 20 February 2023
- ...ale) cable to plug it into your computer. Note that the Micro-USB port can be used only for power because the data lines are not connected. ...hen connected to a computer via USB-A port. You can set up the computer to be in the same network as PineCube and connect to PineCube via SSH and/or Stre10 KB (1,452 words) - 10:30, 30 March 2023
- ...d]] and print yourself. Recommended material is PLA, excellent results can be obtained using a 0.25mm nozzle, though slightly larger sizes should work fi To use the pegs, open your case and remove the ROCK64 from within. Be sure to pull out the light guide and rubber plug to remove it, or else it w4 KB (747 words) - 13:17, 5 February 2023
- * USB/UART Programming/Console Adapter (PMPROG01) driver can be [https://www.silabs.com/products/mcu/Pages/USBtoUARTBridgeVCPDrivers.aspx D * Termite can be downloaded at [http://www.compuphase.com/software_termite.htm CompuPhase We8 KB (1,349 words) - 16:54, 20 February 2023
- The Quartz64 model A can be made to fit this case, however some filing of one of the holes is necessary1,013 bytes (174 words) - 19:00, 20 February 2023
- The PineTime Dev Kit comes with the back not glued down to allow it to be easily reprogrammed, however the kit does not include an hardware programme ...') port ''4444'' using telnet and invoke OpenOCD commands. GDB should also be available on port ''3333''.8 KB (1,222 words) - 03:02, 16 March 2023
- ...EU and Asia in particular, require the entirety of the modem's firmware to be licensed. Therefore, the PinePhone cannot ship with an unlicensed firmware, | Some settings are stored here, along with commands that need to be picked by LK on next boot (to reboot to fastboot or recovery mode)9 KB (1,443 words) - 13:35, 16 March 2023
- | https://youtu.be/4aFDjymXjOw | https://youtu.be/gUVEz-pxhgg7 KB (1,024 words) - 05:08, 21 April 2023
- # '''On the PinePhone Pro''': The eMMC might have to be overruled to boot from the microSD card, see [[PinePhone Pro#Boot order]] {{Info|At this the image file does not have to be extracted from the archive format. Balena Etcher handles the extracting aut12 KB (1,957 words) - 14:50, 12 August 2023
- ...inux running on the board, not some vendor provided kernel that will never be receiving updates. A mainline-first approach allows for the boards to conti ...Before NetBSD 10 is released, the latest version of NetBSD-current should be used.9 KB (1,424 words) - 15:00, 26 September 2023
- ...plan on using it. Don't bend the wires too much as they're thin, you won't be able to reconnect it. Keep in mind that keeping it connected during develop The Pogo Pins are meant to be connected temporarily to PineTime's SWD port for firmware flashing and simp4 KB (737 words) - 06:26, 18 May 2022