Difference between revisions of "ROCKPro64 Hardware compatibility"
Jump to navigation
Jump to search
JerseyDevil (talk | contribs) m (→PCIe devices) |
(Add two PCIe SATA cards) |
||
| (3 intermediate revisions by one other user not shown) | |||
| Line 26: | Line 26: | ||
|- | |- | ||
| SATA Controller || Ziyituod SATA Card ASM 1062+1093 6-Port || 1b21:0625 || Mainline-4.4 (armbian) || good || tested with 6 disks || | | SATA Controller || Ziyituod SATA Card ASM 1062+1093 6-Port || 1b21:0625 || Mainline-4.4 (armbian) || good || tested with 6 disks || | ||
|- | |||
| SATA Controller || BEYMEI RAID 4-Port, Marvell 88SE9230 chip || 1b4b:9230 || Ayufan-5.6.0-1137 || good || Tested with 3 disks in RAID 5. I added pci=nomsi to /boot/extlinux/extlinux.conf kernel parameters and an udev rule before the disks were recognized: ACTION=="add", SUBSYSTEM=="pci", ATTR{vendor}=="0x1b4b", ATTR{device}=="0x9230", RUN+="/bin/bash -c 'echo %k > /sys/bus/pci/drivers/ahci/bind'" | |||
|- | |||
| SATA Controller || QNINE 4-Port, Marvell 88SE9215 chip || || Ayufan-5.6.0-1137 || very slow || Tested with 3 disks in RAID 5. Top speeds were around 50 MiB/s but quickly dropped to below 2 MiB/s due to SATA CRC errors | |||
|- | |- | ||
| Host Bus Adapter || LSI SAS 9211-4i || 1000:0070 || Ayufan-4.4.197 || good || tested with four disks attached | | Host Bus Adapter || LSI SAS 9211-4i || 1000:0070 || Ayufan-4.4.197 || good || tested with four disks attached | ||
| Line 34: | Line 38: | ||
!Type || Make/Model || Size || Hardware IDs || Kernel || Result || Notes || Power options<br/>Active only || Save<br/>power<br/>setting? | !Type || Make/Model || Size || Hardware IDs || Kernel || Result || Notes || Power options<br/>Active only || Save<br/>power<br/>setting? | ||
|- | |- | ||
| NVMe || Samsung 970 Evo || 500 GB || || Mainline | | NVMe || Samsung 970 Evo || 500 GB || || Mainline 5.6 || good || - || defaults || defaults | ||
|- | |||
| NVMe || Samsung 960 Evo || 500 GB || 144d:a804 || Mainline 5.13-rc4 || doesn't work || Likely due to 64/32 BAR mismatch issue on Linux 5.11+ || defaults || defaults | |||
|} | |} | ||
Revision as of 16:39, 17 June 2021
ROCKPro64 accessories - by type
PCIe devices
| Type | Make/Model | Hardware IDs | Kernel | Result | Notes | |
|---|---|---|---|---|---|---|
| NIC | Intel I350 Dual Port | Mainline-5.4 | good | SR-IOV fails | ||
| NIC | Intel I350 Quad Port | ? | ||||
| NIC | Intel X520 Dual Port | 8086:10fb | Mainline-5.6 | good | SR-IOV fails | |
| NIC | Intel 82571EB Dual Port (HP NC360T) | Mainline-5.6 | crash | kernel crash on boot | ||
| NIC | Intel 82575/82576 | 8086:1521 | OpenWrt 21.02-rc1 ; 5.4.111-1 | good | opkg: kmod-igb ; OpenWrt 21.02-rc1 5.4.111-1 ; ~92.8 KB ; Kernel modules for Intel(R) 82575/82576 PCI-Express Gigabit Ethernet adapters. | |
| GPU | nVidia GTX-645 | Mainline-5.4 | crash | BAR size too small, triggers PCIe error handling bug | ||
| PCIe Switch | PCIE-EUX1-04 Ver.002 | Mainline-5.4 | good | |||
| SATA Controller | ASM1062 4-Port | Mainline-5.6 | good | tested only with one disk attached | ||
| SATA Controller | ASM1062 (rev 02) 4-Port | 1d87:0100 | Ayufan-4.4.190 | good | tested with four disks, 3 in raid 5 | |
| SATA Controller | IOCrest (Same as Syba?) SI-PEX40063 4-port, Marvell 88SE9235 chip | 1b4b:9235 | Debian unstable 5.7, 5.8 | good | Tested with two disks. SATA errors occurred with a WD Red drive in a cheap enclosure; resolved by connecting the same drive directly to the card. | |
| SATA Controller | Ziyituod SATA Card ASM 1062+1093 6-Port | 1b21:0625 | Mainline-4.4 (armbian) | good | tested with 6 disks | |
| SATA Controller | BEYMEI RAID 4-Port, Marvell 88SE9230 chip | 1b4b:9230 | Ayufan-5.6.0-1137 | good | Tested with 3 disks in RAID 5. I added pci=nomsi to /boot/extlinux/extlinux.conf kernel parameters and an udev rule before the disks were recognized: ACTION=="add", SUBSYSTEM=="pci", ATTR{vendor}=="0x1b4b", ATTR{device}=="0x9230", RUN+="/bin/bash -c 'echo %k > /sys/bus/pci/drivers/ahci/bind'" | |
| SATA Controller | QNINE 4-Port, Marvell 88SE9215 chip | Ayufan-5.6.0-1137 | very slow | Tested with 3 disks in RAID 5. Top speeds were around 50 MiB/s but quickly dropped to below 2 MiB/s due to SATA CRC errors | ||
| Host Bus Adapter | LSI SAS 9211-4i | 1000:0070 | Ayufan-4.4.197 | good | tested with four disks attached |
NVMe SSD drives
| Type | Make/Model | Size | Hardware IDs | Kernel | Result | Notes | Power options Active only |
Save power setting? |
|---|---|---|---|---|---|---|---|---|
| NVMe | Samsung 970 Evo | 500 GB | Mainline 5.6 | good | - | defaults | defaults | |
| NVMe | Samsung 960 Evo | 500 GB | 144d:a804 | Mainline 5.13-rc4 | doesn't work | Likely due to 64/32 BAR mismatch issue on Linux 5.11+ | defaults | defaults |
USB hardware
| Type | Make/Model | Hardware IDs | Kernel | Result | Notes |
|---|
USB C alternate mode DP
Note that only USB C alternate mode Display Port will pass video. Any HDMI, DVI or VGA port must be converted internally by the device from Display Port - or the device won't work for video.
| Type | Make/Model | Hardware IDs | Kernel | Result | Notes |
|---|
Other hardware
| Type | Make/Model | Hardware IDs | Kernel | Result | Notes |
|---|