Difference between revisions of "Quartz64"

From PINE64
Jump to navigation Jump to search
(→‎Storage: Put eMMC under storage, instead of memory)
(Oops, my bad)
 
(159 intermediate revisions by 27 users not shown)
Line 1: Line 1:
The Quartz64 is the most recent Single Board Computer offering from Pine64, scheduled for release in 2021. It is powered by a Rockchip RK3566 Quad-Core ARM Cortex A55 64-Bit Processor with a MALI G-52 GPU.
[[File:Quartz64modelb.png|400px|thumb|right|The Quartz64 Model B]]


Key features include a PCIe x2 open ended slot (model A) or m.2 (model B), the use of LPDDR4 RAM.
The '''Quartz64''' is the most recent Single Board Computer offering from PINE64, with Model A initially released in June of 2021 and Model B in May of 2022. It is powered by a Rockchip RK3566 Quad-Core ARM Cortex A55 64-Bit Processor with a MALI G-52 GPU.


The Quartz64 is equipped with 2GB, 4GB or 8GB LPDDR4 system memory, and 128Mb SPI boot Flash. There is also an optional eMMC module (up to 128GB) and microSD slot for booting. The board is equipped with 1x USB 3.0 type A Host, 3x USB 2.0 Host, Gigabit Ethernet, GPIO Bus, MiPi DSI interface, eink interface (Model A), eDP interface (model A), touch Panel interface (model A), MiPi CSI interface, as well as many other device interfaces such as UART, SPI, I2C, for makers to integrate with sensors and other peripherals. Many different Operating Systems (OS) are freely available from the open source community, such as Linux (Ubuntu, Debian, Arch), BSD, and Android.
Key features include a PCIe x4 open-ended slot (model A) or M.2 slot (model B) using a single Gen2 lane electrically, and the use of LPDDR4 RAM.


== Software and OS Image Downloads ==
The Quartz64 is available in two LPDDR4 system memory options: 4&nbsp;GB and 8&nbsp;GB. For booting, there is an eMMC module socket (supporting up to 128&nbsp;GB) and microSD slot, as well as a footprint to solder on an SPI flash chip. The board is equipped with HDMI, 1x USB 3.0 Type-A host, 3x USB 2.0 host, Gigabit Ethernet, SATA (model A), GPIO Bus, MiPi DSI interface, e-ink interface (model A), eDP interface (model A), touch panel interface (model A), MiPi CSI interface, as well as many other device interfaces such as UART, SPI, I<sup>2</sup>C, for makers to integrate with sensors and other peripherals. Many different Operating Systems (OS) are freely available from the open source community, such as Linux (Ubuntu, Debian, Arch), BSD, and Android.


* TBD
== Software releases ==
 
Under [[Quartz64 Software Releases]] you will find a complete list of currently supported operating system images, which work with the Quartz64, as well as other related software.
 
== Getting started ==
 
=== Flashing the device ===
 
Natively the board only supports booting the platform firmware from SPI, the eMMC or a microSD card, see [[#Boot order|boot order]]. The platform firmware loaded from there (U-Boot, EDK2, ...) may then allow loading kernels from additional storage mediums or even the network, and they will have their own boot order.
 
The board can be booted by flashing your chosen operating system to a microSD card using another device and inserting the microSD card into the Quartz64, see the article [[Getting started]]. Flashing the eMMC is possible by booting an operating system from the microSD card and overwriting the eMMC from within the booted operating system, or by using [https://pine64.com/product/usb-adapter-for-emmc-module/ the USB eMMC adapter].
 
=== Boot order ===
 
The hardware boot order of the Quartz64 is:
 
# SPI NOR flash
# SPI NAND flash
# eMMC
# microSD card
 
== SoC and Memory Specifications ==
 
[[File:RK3566_icon.png|right]]


== SoC and Memory Specification ==
* Based on [https://www.rock-chips.com/a/en/products/RK35_Series/2021/0113/1274.html Rockchip RK3566]
* Based on [https://www.rock-chips.com/a/en/products/RK35_Series/2021/0113/1274.html Rockchip RK3566]
[[File:RK3566_icon.png|right]]


=== CPU Architecture ===
=== CPU Architecture ===
* [https://developer.arm.com/ip-products/processors/cortex-a/cortex-a55 Quad-core Cortex-A55@1.8GHz]


* Quad-core ARM Cortex-A55 CPU
* [https://developer.arm.com/ip-products/processors/cortex-a/cortex-a55 Quad-core ARM Cortex-A55@1.8GHz]
* AArch32 for full backward compatibility with Armv7
* AArch32 for full backwards compatibility with ARMv7
* ARM Neon Advanced SIMD (single instruction, multiple data) support for accelerated media and signal processing computation
* ARM Neon Advanced SIMD (single instruction, multiple data) support for accelerated media and signal processing computation
* Include VFP hardware to support single and double-precision operations
* Includes VFP hardware to support single and double-precision operations
* ARMv8 Cryptography Extensions
* ARMv8 Cryptography Extensions
* Integrated 32KB L1 instruction cache, 32KB L1 data cache
* Integrated 32KB L1 instruction cache and 32KB L1 data cache per core
* 512KB unified system L3 cache
* 512KB unified system L3 cache
* TrustZone technology support
* [https://developer.arm.com/ip-products/security-ip/trustzone TrustZone] technology support
* [https://www.cnx-software.com/2020/12/01/rockchip-rk3568-processor-to-power-edge-computing-and-nvr-applications 22nm process, believed to be FD-SOI]
 
=== GPU (Graphics Processing Unit) Capabilities ===


=== Graphic Process Unit GPU Capability ===
* [https://developer.arm.com/ip-products/graphics-and-multimedia/mali-gpus/mali-g52-gpu Mali-G52 2EE Bifrost GPU@800MHz]
* [https://developer.arm.com/ip-products/graphics-and-multimedia/mali-gpus/mali-g52-gpu Mali-G52 2EE Bifrost GPU@800MHz]
* 4x Multi-Sampling Anti-Aliasing (MSAA) with minimal performance drop  
* 4x Multi-Sampling Anti-Aliasing (MSAA) with minimal performance drop  
* 128KB L2 Cache configurations
* 128KB L2 Cache configurations
* Support OpenGL ES 1.1, 2.0, and 3.2
* Supports OpenGL ES 1.1, 2.0, and 3.2
* Support Vulkan 1.0 and 1.1
* Supports Vulkan 1.0 and 1.1
* Support OpenCL 2.0 Full Profile
* Supports OpenCL 2.0 Full Profile
* Support 1600Mpix/s fill rate when 800MHz clock frequency
* Supports 1600 Mpix/s fill rate when at 800MHz clock frequency
* Support 38.4GLOPs when 800MHz clock frequency   
* Supports 38.4 GLOP/s when at 800MHz clock frequency   


=== Neural Process Unit NPU Capability ===
=== NPU (Neural Processing Unit) Capabilities ===
* Neural network acceleration engine with processing performance up to 0.8 TOPS
 
* Support integer 8, integer 16 convolution operation
* Neural network acceleration engine with processing performance of up to 0.8 TOPS
* Support deep learning frameworks: TensorFlow, TF-lite, Pytorch, Caffe, ONNX, MXNet, Keras, Darknet
* Supports integer 8 and integer 16 convolution operations
* Supports the following deep learning frameworks: TensorFlow, TF-lite, Pytorch, Caffe, ONNX, MXNet, Keras, Darknet


=== System Memory ===
=== System Memory ===
* RAM Memory Variants: 2GB - 8GB LPDDR4.
 
* Storage Memory: SPI Flash and optional eMMC module from 16GB up to 128GB
* RAM Memory Variants: 2GB (SOQuartz only), 4GB, 8GB LPDDR4.


=== Network ===
=== Network ===
* 10/100/1000Mbps Ethernet
* 10/100/1000Mbps Ethernet
* WiFi 802.11 b/g/n/ac with Bluetooth 5.0 (optional on model A, build in on model B)
** Easily sustains >910 Mbit/s in a <code>--bidir</code> (i.e. sending and receiving at the same time) iperf3 TCP test.
* Wi-Fi 802.11 b/g/n/ac with Bluetooth 5.0 (optional on model A, built in on model B)


=== Storage ===
=== Storage ===
* microSD - bootable, support SDHC and SDXC, storage up to 256GB
 
* USB - 2 ports on model B, 3 ports on model A USB 2.0 Host port, 1 USB 3.0 Host port
* microSD - bootable, supports SDHC and SDXC, storage up to 2TB
* native SATA 2.0 Port (only on model A, share with USB 3.0 host port)
* USB
* optional eMMC module from 16GB up to 128GB
** Model A: 2 USB 2.0 host ports, 1 USB 2.0 OTG port, 1 USB 3.0 host port
** Model B: 1 USB 2.0 host port, 1 USB 2.0 OTG port, 1 USB 3.0 host port
* one native SATA 3.0 6Gb/s Port (only on model A, shared with USB 3.0 host port) (removed in newer revisions due to electrical signalling issues it caused)
* optional eMMC module from 8GB up to 128GB
* 64 Mbit (8 MByte) SPI flash (Model B only), part number '''25Q64DWZPIG''' in the schematic
 
==== eMMC Speeds ====
 
On a 64 GB eMMC module:
 
  $ sudo hdparm -tT /dev/mmcblk1
 
  /dev/mmcblk1:
  Timing cached reads:  2368 MB in  2.00 seconds = 1184.46 MB/sec
  Timing buffered disk reads: 452 MB in  3.01 seconds = 149.98 MB/sec


=== Expansion Ports ===
=== Expansion Ports ===
* HDMI
* eDP - 4 lanes of 2.7Gbps, up to 2560x1600@60Hz (only on model A)
* eDP - 4 lanes of 2.7Gbps, up to 2560x1600@60Hz (only on model A)
* DSI - Display Serial Interface, 4 lanes MiPi, up to 1440P on model A, 2 lanes MiPi, up to 1080p on model B  
* DSI - Display Serial Interface, 4 lanes MiPi, up to 1440P on model A, 2 lanes MiPi, up to 1080p on model B  
Line 61: Line 101:
* RTC - Real Time Clock Battery Connector
* RTC - Real Time Clock Battery Connector
* VBAT - Lithium Battery Connector with temperature sensor input on model A
* VBAT - Lithium Battery Connector with temperature sensor input on model A
* Wifi/BT Module Header - SDIO 3.0 and UART on model A, build in Wifi/BT Module on model B
* Wi-Fi/BT Module Header - SDIO 3.0 and UART on model A, built-in Wi-Fi/BT Module on model B
* 2x20 pins "Pi2" GPIO Header on model B, 2x10 pins GPO header on model A
* 2x20 pins "Pi2" GPIO Header on model B, 2x10 pins GPO header on model A
* PCIe 2x open ended slot on model A, m.2 slot on model B
* PCIe x4 open ended slot on model A, m.2 slot on model B, one Gen2 lane due to SoC constraints
** On Model A, the slot provides 10W of power for the 3.3V supply and however much power your 12V input power supply provides on the 12V supply
 
The PCIe implementation on the RK3566 is much more compatible with a wide range of devices compared to the one on the RK3399 used on the ROCKPro64. This means a lot more devices should work (excluding dGPUs due to a lack of cache snooping ability).
 
==== Combo PHYs ====
 
[[File:rk3566 phy.png|400px]]
 
Several of the I/O options on the RK3566 used in the Quartz64 are using the same I/O lines, meaning that they cannot be used at the same time. The above diagram illustrates how they are connected.
 
In particular, USB 3.0 and the SATA connector on the board are mutually exclusive, and the PCI-e 2.0 lane can be reconfigured into a second SATA port, though an adapter cable needs to be fashioned for this to be useful.
 
=== GPIO Pins (Quartz64 Model A) ===
 
Attention! GPIOs are 3.3V!
 
{| class="wikitable plainrowheaders" border="1"
! scope="col" style="width:20em;" | Assigned To
! scope="col" | Pin no.
! scope="col" | Pin no.
! scope="col" style="width:20em;" | Assigned To
|-
| style="text-align:right;"| 3.3 V
| style="text-align:center; background-color:black; color:gold; font-weight:bold;"| 1
| style="text-align:center; background-color:black; color:gold; font-weight:bold;"| 2
| style="text-align:left;"| 5 V
|-
| style="text-align:right;"| I2C3_SDA_M0 <sup style="font-style:italic;color:green">a,b</sup>
| style="text-align:center; background-color:black; color:gold; font-weight:bold;"| 3
| style="text-align:center; background-color:black; color:gold; font-weight:bold;"| 4
| style="text-align:left;"| 5 V
|-
| style="text-align:right;"| I2C3_SCL_M0 <sup style="font-style:italic;color:green">a,b</sup>
| style="text-align:center; background-color:black; color:gold; font-weight:bold;"| 5
| style="text-align:center; background-color:black; color:gold; font-weight:bold;"| 6
| style="text-align:left;"| GND
|-
| style="text-align:right;"| CPU_REFCLK_OUT
| style="text-align:center; background-color:black; color:gold; font-weight:bold;"| 7
| style="text-align:center; background-color:black; color:gold; font-weight:bold;"| 8
| style="text-align:left;"| UART2_TX_M0_DEBUG
|-
| style="text-align:right;"| GND
| style="text-align:center; background-color:black; color:gold; font-weight:bold;"| 9
| style="text-align:center; background-color:black; color:gold; font-weight:bold;"| 10
| style="text-align:left;"| UART2_RX_M0_DEBUG
|-
| style="text-align:right;"| SPI1_MOSI_M1
| style="text-align:center; background-color:black; color:gold; font-weight:bold;"| 11
| style="text-align:center; background-color:black; color:gold; font-weight:bold;"| 12
| style="text-align:left;"| UART0_TX <sup style="font-style:italic;color:green">a</sup>
|-
| style="text-align:right;"| SPI1_MISO_M1
| style="text-align:center; background-color:black; color:gold; font-weight:bold;"| 13
| style="text-align:center; background-color:black; color:gold; font-weight:bold;"| 14
| style="text-align:left;"| UART0_RX <sup style="font-style:italic;color:green">a</sup>
|-
| style="text-align:right;"| SPI1_CLK_M1
| style="text-align:center; background-color:black; color:gold; font-weight:bold;"| 15
| style="text-align:center; background-color:black; color:gold; font-weight:bold;"| 16
| style="text-align:left;"| GND
|-
| style="text-align:right;"| SPI1_CS0_M1
| style="text-align:center; background-color:black; color:gold; font-weight:bold;"| 17
| style="text-align:center; background-color:black; color:gold; font-weight:bold;"| 18
| style="text-align:left;"| SPDIF_OUT <sup style="font-style:italic;color:green">c</sup>
|-
| style="text-align:right;"| GND
| style="text-align:center; background-color:black; color:gold; font-weight:bold;"| 19
| style="text-align:center; background-color:black; color:gold; font-weight:bold;"| 20
| style="text-align:left;"| 3.3V
|}
 
==== Notes ====
<ol style="list-style-type:lower-alpha">
  <li>can be a PWM pin</li>
  <li>pulled high to 3.3V through 2.2kOhm resistor</li>
  <li>low-pass filtered with cutoff of 220 MHz</li>
</ol>
 
Source: Page 28 of [[File:Quartz64_model-A_schematic_v1.0_20201215.pdf|the board schematics]].
 
=== GPIO Pins (Quartz64 Model B) ===
 
Attention! GPIOs are 3.3V!
 
Interesting alternate pin configurations are listed in [brackets].
 
{| class="wikitable plainrowheaders" border="1"
! scope="col" style="width:20em;" | Assigned To
! scope="col" | Pin no.
! scope="col" | Pin no.
! scope="col" style="width:20em;" | Assigned To
|-
| style="text-align:right;"| 3.3 V
| style="text-align:center; background-color:yellow; color:black; font-weight:bold;"| 1
| style="text-align:center; background-color:red; color:gold; font-weight:bold;"| 2
| style="text-align:left;"| 5 V
|-
| style="text-align:right;"| ''[I2C3_SDA_M0]'' GPIO1_A0_3V3
| style="text-align:center; background-color:green; color:gold; font-weight:bold;"| 3
| style="text-align:center; background-color:red; color:gold; font-weight:bold;"| 4
| style="text-align:left;"| 5 V
|-
| style="text-align:right;"| ''[I2C3_SCL_M0]'' GPIO1_A1_3V3
| style="text-align:center; background-color:green; color:gold; font-weight:bold;"| 5
| style="text-align:center; background-color:black; color:gold; font-weight:bold;"| 6
| style="text-align:left;"| GND
|-
| style="text-align:right;"| GPIO3_C4_3V3
| style="text-align:center; background-color:green; color:gold; font-weight:bold;"| 7
| style="text-align:center; background-color:green; color:gold; font-weight:bold;"| 8
| style="text-align:left;"| UART2_TX
|-
| style="text-align:right;"| GND
| style="text-align:center; background-color:black; color:gold; font-weight:bold;"| 9
| style="text-align:center; background-color:green; color:gold; font-weight:bold;"| 10
| style="text-align:left;"| UART2_RX
|-
| style="text-align:right;"| ''[SPI1_CS0_M1]'' GPIO3_A1_3V3
| style="text-align:center; background-color:green; color:gold; font-weight:bold;"| 11
| style="text-align:center; background-color:green; color:gold; font-weight:bold;"| 12
| style="text-align:left;"| GPIO3_A3_3V3 ''[I2S3_SCLK_M0]''
|-
| style="text-align:right;"| ''[I2S3_MCLK_M0]'' GPIO3_A2_3V3
| style="text-align:center; background-color:green; color:gold; font-weight:bold;"| 13
| style="text-align:center; background-color:black; color:gold; font-weight:bold;"| 14
| style="text-align:left;"| GND
|-
| style="text-align:right;"| GPIO3_B0_3V3
| style="text-align:center; background-color:green; color:gold; font-weight:bold;"| 15
| style="text-align:center; background-color:green; color:gold; font-weight:bold;"| 16
| style="text-align:left;"| GPIO3_B1_3V3
|-
| style="text-align:right;"| 3.3V
| style="text-align:center; background-color:yellow; color:black; font-weight:bold;"| 17
| style="text-align:center; background-color:green; color:gold; font-weight:bold;"| 18
| style="text-align:left;"| GPIO3_B2_3V3
|-
| style="text-align:right;"| GPIO4_C3_3V3
| style="text-align:center; background-color:green; color:gold; font-weight:bold;"| 19
| style="text-align:center; background-color:black; color:gold; font-weight:bold;"| 20
| style="text-align:left;"| GND
|-
| style="text-align:right;"| GPIO4_C5_3V3
| style="text-align:center; background-color:green; color:gold; font-weight:bold;"| 21
| style="text-align:center; background-color:green; color:gold; font-weight:bold;"| 22
| style="text-align:left;"| GPIO3_C1_3V3 ''[SPI1_MOSI_M1]''
|-
| style="text-align:right;"| GPIO4_C2_3V3
| style="text-align:center; background-color:green; color:gold; font-weight:bold;"| 23
| style="text-align:center; background-color:green; color:gold; font-weight:bold;"| 24
| style="text-align:left;"| GPIO4_C6_3V3
|-
| style="text-align:right;"| GND
| style="text-align:center; background-color:black; color:gold; font-weight:bold;"| 25
| style="text-align:center; background-color:green; color:gold; font-weight:bold;"| 26
| style="text-align:left;"| GPIO4_D1_3V3
|-
| style="text-align:right;"| I2C4_SDA_M0
| style="text-align:center; background-color:blue; color:gold; font-weight:bold;"| 27
| style="text-align:center; background-color:blue; color:gold; font-weight:bold;"| 28
| style="text-align:left;"| I2C4_SCL_M0
|-
| style="text-align:right;"| GPIO3_B3_3V3
| style="text-align:center; background-color:green; color:gold; font-weight:bold;"| 29
| style="text-align:center; background-color:black; color:gold; font-weight:bold;"| 30
| style="text-align:left;"| GND
|-
| style="text-align:right;"| GPIO3_B4_3V3
| style="text-align:center; background-color:green; color:gold; font-weight:bold;"| 31
| style="text-align:center; background-color:green; color:gold; font-weight:bold;"| 32
| style="text-align:left;"| GPIO3_C2_3V3 ''[SPI1_MISO_M1]''
|-
| style="text-align:right;"| ''[SPI1_CLK_M1]'' GPIO3_C3_3V3
| style="text-align:center; background-color:green; color:gold; font-weight:bold;"| 33
| style="text-align:center; background-color:black; color:gold; font-weight:bold;"| 34
| style="text-align:left;"| GND
|-
| style="text-align:right;"| ''[I2S3_LRCK_M0]'' GPIO3_A4_3V3
| style="text-align:center; background-color:green; color:gold; font-weight:bold;"| 35
| style="text-align:center; background-color:green; color:gold; font-weight:bold;"| 36
| style="text-align:left;"| GPIO3_A7_3V3
|-
| style="text-align:right;"| ''[SPDIF_TX_M0]'' GPIO1_A4_3V3
| style="text-align:center; background-color:green; color:gold; font-weight:bold;"| 37
| style="text-align:center; background-color:green; color:gold; font-weight:bold;"| 38
| style="text-align:left;"| GPIO3_A6_3V3 ''[I2S3_SDI_M0]''
|-
| style="text-align:right;"| GND
| style="text-align:center; background-color:black; color:gold; font-weight:bold;"| 39
| style="text-align:center; background-color:green; color:gold; font-weight:bold;"| 40
| style="text-align:left;"| GPIO3_A5_3V3 ''[I2S3_SDO_M0]''
|}
 
Source: Page 24 of [https://files.pine64.org/doc/quartz64/Quartz64_model-B_Schematic-V1.3_20220124.pdf the board schematics].
 
== Quartz64 Board Information, Schematics, and Certifications ==


== Quartz64 board Information, Schematics, and Certifications ==
=== Model "A" ===
* Model "A" Baseboard Dimensions: 133mm x 80mm x 19mm
* Input Power: DC 12V @ 3A 5.5mmOD/2.1mmID Barrel DC Jack connector


* Quartz64 Model "A" SBC Schematic and PCB Board Resource:
Model "A" Baseboard Dimensions: 133mm x 80mm x 19mm
** [https://files.pine64.org/doc/quartz64/Quartz64_model-A_schematic_v1.0_20201124.pdf Quartz64 Model "A" SBC Schematic ver 1.0 20201124 PDF file]
** [https://files.pine64.org/doc/quartz64/Quartz64_model-A_V1.0_connector_placement.pdf Quartz64 Model "A" SBC PCB Connector placement PDF file]


* Model "B" Baseboard Dimensions: 85mm x 56mm x 18.8mm
Input Power: DC 12V @ 3A 5.5mmOD/2.1mmID center-positive Barrel DC Jack connector
* Input Power: DC 5V @ 3A 3.5mmOD/1.35mmID Barrel DC Jack connector


* Quartz64 Model "B" SBC Schematic and PCB Board Resource:
Quartz64 Model "A" SBC Schematic and PCB Board Resource:
** Quartz64 Model "B" SBC Schematic not yet available
** [https://files.pine64.org/doc/quartz64/Quartz64%20model-B%20PCB%20placement.pdf Quartz64 Model "B" SBC PCB Connector placement PDF file]


* Certification:
* [https://files.pine64.org/doc/quartz64/Quartz64_model-A_schematic_v2.0_20210427.pdf Quartz64 Model "A" SBC Schematic ver 2.0 20210427 PDF file]
** Not yet available
* [https://files.pine64.org/doc/quartz64/Quartz64_model-A_V2.0_connector_placement.pdf Quartz64 Model "A" SBC PCB Connector placement PDF file]


Certifications:
* Disclaimer: Please note that PINE64 SBC is not a "final" product and in general certification is not necessary. However, PINE64 still submit the SBC for FCC and CE certification and obtain the certificates to proof that SBC board is capable on passing the testing. Please note a final commercial product needs to performs its owns testing and obtains its owns certificates.
* [https://files.pine64.org/doc/cert/Quartz64%20Model-A%20CE%20certification-S21051101701001.pdf Quartz64 model-A CE Certificate]
* [https://files.pine64.org/doc/cert/Quartz64%20Model-A%20FCC%20certification-S21051101702001.pdf Quartz64 model-A FCC Certificate]
=== Model "B" ===
Model "B" Baseboard Dimensions: 85mm x 56mm x 18.8mm
Input Power: DC 5V @ 3A 3.5mmOD/1.35mmID center-positive Barrel DC Jack connector
Quartz64 Model "B" SBC Schematic and PCB Board Resource:
* [https://files.pine64.org/doc/quartz64/Quartz64_model-B_Schematic-V1.3_20220124.pdf Quartz64 Model "B" SBC Schematic ver 1.3 20220124 PDF file]
* [https://files.pine64.org/doc/quartz64/Quartz64_model-B_PCB_Components_Placement-V1.2_20211014.pdf Quartz64 Model "B" SBC PCB Connector placement PDF file]
* Please note that v1.2 and V1.3 schematic and component placement are identical, just some component value changed.
* Note: Model B uses a Molex PicoBlade compatible connector for the RTC battery. The Pine64 Backup Battery Holders come with a JST PH type connector. To use the Pine64 RTC Backup Battery Holder, the connector on the battery holder will need to be modified with a PicoBlade type connector.


== Datasheets for Components and Peripherals ==
== Datasheets for Components and Peripherals ==
* Rockchip RK3566 SoC information:
** [https://files.pine64.org/doc/quartz64/Rockchip%20RK3566%20Datasheet%20V1.0-20201210.pdf Rockchip RK3566 ver 1.0 datasheet, already got release permission from Rockchip]
* LPDDR4 (200 Balls) SDRAM:
** [https://files.pine64.org/doc/datasheet/rockpro64/SM512M32Z01MD2BNP(200BALL).pdf Micron LPDDR4 Mobile LPDDR4 Datasheet]
* eMMC information:
** [https://files.pine64.org/doc/rock64/PINE64_eMMC_Module_20170719.pdf PINE64 eMMC module schematic]
** [https://files.pine64.org/doc/rock64/usb%20emmc%20module%20adapter%20v2.pdf PINE64 USB adapter for eMMC module V2 schematic]
** [https://files.pine64.org/doc/rock64/USB%20adapter%20for%20eMMC%20module%20PCB.tar PINE64 USB adapter for eMMC module PCB in JPEG]
** [https://files.pine64.org/doc/datasheet/pine64/E-00517%20FORESEE_eMMC_NCEMAM8B-16G%20SPEC.pdf 16GB Foresee eMMC Datasheet]
** [https://files.pine64.org/doc/datasheet/pine64/SDINADF4-16-128GB-H%20data%20sheet%20v1.13.pdf 32GB/64GB/128GB SanDisk eMMC Datasheet]
* SPI NOR Flash information:
** [https://files.pine64.org/doc/datasheet/pine64/w25q128jv%20spi%20revc%2011162016.pdf WinBond 128Mb SPI Flash Datasheet]
** [https://files.pine64.org/doc/datasheet/pine64/GD25Q128C-Rev2.5.pdf GigaDevice 128Mb SPI Flash Datasheet]
* E-ink Panel information:
** [https://files.pine64.org/doc/quartz64/Eink%20P-511-754-V3_ES103TC1%20Specification%20V3.0(Signed)-20190702.pdf Eink 10.3" 1872x1404 ES103TC1 Flex Panel Specification]
** [https://files.pine64.org/doc/quartz64/Eink%20P-511-828-V1_ED103TC2%20Formal%20Spec%20V1.0_20190514.pdf Eink 10.3" 1872x1404 ES103TC1 Glass Panel Specification]
* LCD Touch Screen Panel information:
** [https://files.pine64.org/doc/datasheet/pine64/FY07024DI26A30-D_feiyang_LCD_panel.pdf 7.0" 1200x600 TFT-LCD Panel Specification]
** [https://files.pine64.org/doc/datasheet/pine64/HK70DR2459-PG-V01.pdf Touch Panel Specification]
** [https://files.pine64.org/doc/datasheet/pine64/GT911%20Capacitive%20Touch%20Controller%20Datasheet.pdf GOODiX GT911 5-Point Capacitive Touch Controller Datasheet]
* Ethernet PHY information:
** [https://files.pine64.org/doc/datasheet/pine64/rtl8211e(g)-vb(vl)-cg_datasheet_1.6.pdf Realtek RTL8211 10/100/1000M Ethernet Transceiver]
* WiFi/BT module info:
** [https://files.pine64.org/doc/datasheet/rockpro64/AP6256%20datasheet_V1.3_12202017.pdf AMPAK AP6256 11AC WiFi + Bluetooth5.0 Datasheet]]
* Enclosure information:
** [https://files.pine64.org/doc/datasheet/case/playbox_enclosure_20160426.stp Playbox Enclosure 3D file]
** [https://files.pine64.org/doc/datasheet/case/ABS_enclosure_20160426.stp ABS Enclosure 3D file]
** [https://files.pine64.org/doc/datasheet/case/pine64%20Die%20Cast%20casing-final.jpg Outdoor Aluminum Cast Dust-proof IP67 Enclosure Drawing]
* Connector information:
** [https://files.pine64.org/doc/datasheet/pine64/ePH.pdf 2.0mm PH Type connector specification use in Lithium Battery (VBAT) port and RTC Battery port]
** [https://files.pine64.org/doc/datasheet/pine64/0.5FPC%20Front%20Open%20Connector%20H=1.5.pdf 0.5mm Pitch cover type FPC connector specification use in DSI port, TP port and CSI port]


== Android SDK ==
Rockchip RK3566 SoC information:
* [https://files.pine64.org/doc/quartz64/Rockchip%20RK3566%20Datasheet%20V1.0-20201210.pdf Rockchip RK3566 ver 1.0 datasheet, already got release permission from Rockchip]
* [https://opensource.rock-chips.com/images/2/26/Rockchip_RK3568_TRM_Part1_V1.3-20220930P.PDF Rockchip RK3566 and RK3568 TRM (Technical Reference Manual)]
 
Rockchip PMU (Power Management Unit) Information:
* [https://www.rockchip.fr/RK817%20datasheet%20V1.01.pdf Rockchip RK817 ver 1.01 datasheet for Quartz64 model A]
* [https://www.rockchip.fr/RK809%20datasheet%20V1.01.pdf Rockchip RK809 ver 1.01 datasheet for Quartz64 model B and SOQuartz]
 
LPDDR4 (200 Balls) SDRAM:
* [https://files.pine64.org/doc/datasheet/rockpro64/SM512M32Z01MD2BNP(200BALL).pdf Micron LPDDR4 Mobile LPDDR4 Datasheet]
 
eMMC information:
* [https://files.pine64.org/doc/rock64/PINE64_eMMC_Module_20170719.pdf PINE64 eMMC module schematic]
* [https://files.pine64.org/doc/rock64/usb%20emmc%20module%20adapter%20v2.pdf PINE64 USB adapter for eMMC module V2 schematic]
* [https://files.pine64.org/doc/rock64/USB%20adapter%20for%20eMMC%20module%20PCB.tar PINE64 USB adapter for eMMC module PCB in JPEG]
* [https://files.pine64.org/doc/datasheet/pine64/E-00517%20FORESEE_eMMC_NCEMAM8B-16G%20SPEC.pdf 16GB Foresee eMMC Datasheet]
* [https://files.pine64.org/doc/datasheet/pine64/SDINADF4-16-128GB-H%20data%20sheet%20v1.13.pdf 32GB/64GB/128GB SanDisk eMMC Datasheet]
 
SPI NOR Flash information:
* [https://files.pine64.org/doc/datasheet/pine64/w25q128jv%20spi%20revc%2011162016.pdf WinBond 128Mb SPI Flash Datasheet]
* [https://files.pine64.org/doc/datasheet/pine64/GD25Q128C-Rev2.5.pdf GigaDevice 128Mb SPI Flash Datasheet]
 
E-ink Panel information:
* [https://files.pine64.org/doc/quartz64/Eink%20P-511-754-V3_ES103TC1%20Specification%20V3.0(Signed)-20190702.pdf Eink 10.3" 1872x1404 ES103TC1 Flex Panel Specification]
* [https://files.pine64.org/doc/quartz64/Eink%20P-511-828-V1_ED103TC2%20Formal%20Spec%20V1.0_20190514.pdf Eink 10.3" 1872x1404 ES103TC1 Glass Panel Specification]
* [https://files.pine64.org/doc/datasheet/PineNote/TI%20PMU-TPS651851.pdf TPS65185x PMIC for E-Ink Enabled Electronic Paper Display Datasheet]
 
LCD Touch Screen Panel information:
* [https://files.pine64.org/doc/datasheet/pine64/FY07024DI26A30-D_feiyang_LCD_panel.pdf 7.0" 1024x600 TFT-LCD Panel Specification]
* [https://files.pine64.org/doc/datasheet/pine64/HK70DR2459-PG-V01.pdf Touch Panel Specification]
* [https://files.pine64.org/doc/datasheet/pine64/GT911%20Capacitive%20Touch%20Controller%20Datasheet.pdf GOODiX GT911 5-Point Capacitive Touch Controller Datasheet]
 
Ethernet PHY information:
* [https://files.pine64.org/doc/datasheet/pine64/rtl8211e(g)-vb(vl)-cg_datasheet_1.6.pdf Realtek RTL8211 10/100/1000M Ethernet Transceiver]
 
Wi-Fi/BT module info:
* [https://files.pine64.org/doc/datasheet/rockpro64/AW-CM256SM_DS_DF_V1.9_STD.pdf Azurewave CM256SM 11AC Wi-Fi + Bluetooth5.0 Datasheet]
 
IR LED:
* [https://media.digikey.com/pdf/Data%20Sheets/Everlight%20PDFs/IRM-36xx_Series.pdf IRM-3638 Datasheet]
 
Enclosure information:
* [https://files.pine64.org/doc/datasheet/case/playbox_enclosure_20160426.stp Playbox Enclosure 3D file]
* [https://files.pine64.org/doc/datasheet/case/ABS_enclosure_20160426.stp ABS Enclosure 3D file]
* [https://files.pine64.org/doc/datasheet/case/pine64%20Die%20Cast%20casing-final.jpg Outdoor Aluminum Cast Dust-proof IP67 Enclosure Drawing]
* [https://www.printables.com/model/269572-pine-quartz-64-a-full-case 3D Printable Enclosure for Model A]
* [https://www.printables.com/model/269575-pine-quartz-64-a-open-frame Open Frame for Model A]
 
Connector information:
* [https://files.pine64.org/doc/datasheet/pine64/ePH.pdf 2.0mm PH Type connector specification use in Lithium Battery (VBAT) port (Model A)]
* [https://www.molex.com/pdm_docs/sd/533980271_sd.pdf 1.25mm Picoblade Type connector specification used in RTC Battery port (Model B)]
* [https://files.pine64.org/doc/datasheet/pine64/0.5FPC%20Front%20Open%20Connector%20H=1.5.pdf 0.5mm Pitch cover type FPC connector specification use in DSI port, TP port and CSI port]
 
== Development efforts ==
 
{{SeeMainArticle|Quartz64 Development}}
 
Information and resources of the ongoing development effort for the Quartz64 can be found on the [[Quartz64 Development]] page, where the current status of various board functions can be found, and whether they have landed in upstream.
 
* [https://gitlab.com/pine64-org/quartz-bsp Quartz64 BSP Gitlab Page]
 
== Enclosures ==
 
Note: Please expand this section with more cases known to work.
 
=== Model "A" ===
 
All enclosures that fit the ROCKPro64 should fit the Quartz64 Model "A", as the I/O has been laid out the same on purpose.
 
* [[Model A Acrylic Open Enclosure]] - but see the troubleshooting section below.
* [[Quartz64 Premium Aluminium Case|RockPro64 Premium Aluminium Case]]
* [[ROCKPro64#3D printable ITX mounting brackets]] (Not an enclosure but allows to mount the board in an ATX/ITX case)
 
=== Model "B" ===
 
* [[Model B Acrylic Open Enclosure]]
* the ROCK64 aluminium enclosure '''does not''' work, as the DC input jack is placed differently
 
== Troubleshooting ==
 
=== Stability/Boot Issues With Missing Battery Shunt ===
 
If there is no battery plugged into the board, the jumper labelled "ON/OFF_BATT" must be in place. If this is set wrong, stability issues such as failures to boot will occur. '''This affects model A only'''
 
=== No Ethernet Connectivity ===
 
Make sure the kernel is built with <code>CONFIG_MOTORCOMM_PHY</code> set to <code>y</code>. Building it as a module (<code>m</code>) and then relying on module auto-loading is unlikely to work, because if the generic PHY driver is built in it will bind to the PHY first, unless you include the motorcomm module in your initramfs.
 
Note: Starting with [https://salsa.debian.org/kernel-team/linux/-/merge_requests/551 Debian's <code>6.1~rc3-1~exp1</code> kernel] the module is included, but set to <code>m</code> and I (Diederik) have verified that it gets included in the initramfs and '''works''' on Model-A and Model-B with the [[Quartz64#Plebian]] images.
 
=== "Model A" Acrylic Case Doesn't Fit ===
 
The Quartz64 does not really fit onto the bottom plate of the [[Model A Acrylic Open Enclosure]]. This is because the "Mic" connector at the bottom of the board interferes with one of the posts. A workaround is to find out which post that is (you have a 50% chance of guessing it right, accounting for rotating the board) and then filing away the corner of the post pointing inwards by a few millimeters.
 
[[File:Quartz64-audio-jack-spacer-issue.jpg|400px]]
 
An alternate solution may be to place plastic spacers with a smaller outer diameter in between the acrylic bottom plate posts and the SBC board.
 
=== No GPU Acceleration with Debian "Bullseye" Userland ===
 
Debian Bullseye ships a Mesa version that is too old to contain the required patches for the RK356x SoC's GPU. Upgrade to Bookworm.
 
=== Wireless Connectivity Doesn't Work ===
 
ROCKPro64 wireless module may have CYW43455 or CYW43456 chips on board (not sure if this is the same for Quartz64 model B). Both chips are supported by <code>brcmfmac</code> Wi-Fi driver and <code>btbcm</code> Bluetooth driver.
 
For CYW43455 drivers attempt to load <code>/lib/firmware/brcm/brcmfmac43455-sdio.bin</code> for Wi-Fi and <code>/lib/firmware/brcm/BCM4345C0.hcd</code> for Bluetooth. Corresponding firmware files for CYW43456 are <code>/lib/firmware/brcm/brcmfmac43456-sdio.bin</code> and <code>/lib/firmware/brcm/BCM4345C5.hcd</code>.
 
On Manjaro firmware files for both Bluetooth and Wi-Fi on CYW43456 on are provided by <code>ap6256-firmware</code> package (<code>pacman -S ap6256-firmware</code>).
 
However for CYW43455 wi-fi firmware is in the <code>linux-firmware</code> package and bluetooth is in the <code>firmware-raspberrypi</code> (<code>pacman -S linux-firmware firmware-raspberrypi</code>). <code>linux-firmware</code> package is missing device specific symlinks for quartz64-a. To create them execute:
 
# ln -s brcmfmac43455-sdio.bin /lib/firmware/brcm/brcmfmac43455-sdio.pine64,quartz64-a.bin
# ln -s brcmfmac43455-sdio.AW-CM256SM.txt /lib/firmware/brcm/brcmfmac43455-sdio.pine64,quartz64-a.txt
 
As of 2022-10-19 device tree in mainline kernel for Quartz64 model A has wrong configuration for the Bluetooth driver. [https://patchwork.kernel.org/project/linux-rockchip/patch/20220926125350.64783-1-leo@nabam.net/ Patch] is submitted to the LKML and accepted and included upstream in 6.1-rc7. It's possible to modify dtb file provided by the current kernel using device tree compiler to enable Bluetooth or perform <code>make dtbs</code> in the patched kernel tree to get updated dtb file (<code>arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.dtb</code>). Issue manifests itself with following errors in `dmesg`:
 
  command 0x0c03 tx timeout
  Bluetooth: hci0: BCM: Reset failed (-110)
 
== How-To ==
 
=== Connect Debug UART ===
 
The easiest way to get debug output is to connect a 3.3V 1.5mbaud capable UART adapter to the board.
 
To connect it, connect the ground lead to pin 6, and the RX/TX leads to pins 8 and 10 (consider swapping them if you get no output, things are often mislabeled). These pins are "UART2" in the above GPIO table.
 
Open a serial terminal at 1500000 bauds, e.g.
 
$ picocom -b 1500000 /dev/ttyUSB0
 
=== Disable Heartbeat LED (Linux) ===
 
The flashing LED is called the "heartbeat LED", it blinks in a heart rhythm like fashion once the kernel is running. To disable it, you can run
 
# echo none > /sys/class/leds/user-led/trigger
 
On model A LED device is called "diy-led", not "user-led".
 
On a system with systemd, you can do this as soon as the system is ready to be logged in with a systemd unit like this:
 
[Unit]
Description=Turn off heartbeat LED
Wants=multi-user.target
After=multi-user.target
[Install]
WantedBy=multi-user.target
[Service]
Type=simple
ExecStart=sh -c 'echo none > /sys/class/leds/user-led/trigger'
 
Place it in ''/etc/systemd/system/user-led.service'', and run
 
# systemctl daemon-reload
# systemctl enable user-led.service
 
Upon rebooting, you will now notice that the heartbeat LED will blink during boot-up, but stops blinking as soon as the multi-user target is reached (i.e. the user can log in).
 
=== SATA on model A ===
 
On model A USB 3.0 and SATA ports are using the same I/O line and can't be used simultaneously. By default USB 3.0 is enabled in Linux device tree and SATA is disabled. FDT modifications are required to turn SATA on.
 
Following script is tested on Manjaro but should work on the other distributions with minimal changes. Device tree compiler package usually provides fdtput command (on Manjaro run: <code>pacman -S dtc</code>)
 
# cp /boot/dtbs/rockchip/rk3566-quartz64-a.dtb /boot/dtbs/rockchip/rk3566-quartz64-a-sata.dtb
# fdtput -t s -v /boot/dtbs/rockchip/rk3566-quartz64-a-sata.dtb /usb@fd000000 status disabled
# fdtput -t s -v /boot/dtbs/rockchip/rk3566-quartz64-a-sata.dtb /sata@fc400000 status okay
# sed -i 's#^FDT /dtbs/rockchip/rk3566-quartz64-a.dtb$#FDT /dtbs/rockchip/rk3566-quartz64-a-sata.dtb#' /boot/extlinux/extlinux.conf
# systemctl reboot
 
=== Using a PCF8574 on Model A ===
 
See [[Quartz64 Model A using a PCF8574]].
 
=== Using a battery on Model A ===
 
See [[Quartz64 Model A Using a battery]].
 
=== Connecting a MIPI-DSI display ===
 
See [[Quartz64 connecting a MIPI-DSI display]].
 
=== Building Mainline U-Boot ===
 
See [[Quartz64 Building U-Boot]].
 
== Frequently Asked Questions ==
 
=== Do I Need A Fan/What Heatsink Do I Need? ===
 
You don't need a fan. The [https://pine64.com/product/rockpro64-20mm-mid-profile-heatsink/ 20mm medium heatsink for Model A is plenty enough]. For Model B, the [https://pine64.com/product/small-fan-type-heatsink/ fan type heatsink] will do fine.
 
=== Can This Run A Minecraft Server? ===


=== Android 11 SDK  ===
Yes! Sort of. Testing on an 8GB Model A with PaperMC, [[User:CounterPillow]] was able to out-row world generation in a boat with just one player online, but aside from the slow world gen (which can be pre-generated) the server handled things like TNT explosions and mobs fine. It'll probably do okay with 1-3 players.
* [http://files.pine64.org/SDK/Quartz64/QUARTZ64_SDK_android11.tar.gz Direct Download from pine64.org]
** MD5 (TAR-GZip file): 77c2ff57ea3372fb04da7fb49e17d12b
** File Size: 79.00GB


=== Do I Need The 5A Power Supply For Model A? ===


== Other Resources ==
You only need the 5A power supply for Model A if you plan on connecting hard disk drives to the 12V header on the board.


=== How Much Power Does It Consume? ===


For Model B, it's <2W in idle (powertop tunables not set), and <5W under full CPU load (<code>stress-ng -c4</code>). Model A will be similar as it's the same SoC.


[[Category:Quartz64]]
[[Category:Quartz64]] [[Category:Rockchip RK3566]]

Latest revision as of 07:56, 14 November 2023

The Quartz64 Model B

The Quartz64 is the most recent Single Board Computer offering from PINE64, with Model A initially released in June of 2021 and Model B in May of 2022. It is powered by a Rockchip RK3566 Quad-Core ARM Cortex A55 64-Bit Processor with a MALI G-52 GPU.

Key features include a PCIe x4 open-ended slot (model A) or M.2 slot (model B) using a single Gen2 lane electrically, and the use of LPDDR4 RAM.

The Quartz64 is available in two LPDDR4 system memory options: 4 GB and 8 GB. For booting, there is an eMMC module socket (supporting up to 128 GB) and microSD slot, as well as a footprint to solder on an SPI flash chip. The board is equipped with HDMI, 1x USB 3.0 Type-A host, 3x USB 2.0 host, Gigabit Ethernet, SATA (model A), GPIO Bus, MiPi DSI interface, e-ink interface (model A), eDP interface (model A), touch panel interface (model A), MiPi CSI interface, as well as many other device interfaces such as UART, SPI, I2C, for makers to integrate with sensors and other peripherals. Many different Operating Systems (OS) are freely available from the open source community, such as Linux (Ubuntu, Debian, Arch), BSD, and Android.

Software releases

Under Quartz64 Software Releases you will find a complete list of currently supported operating system images, which work with the Quartz64, as well as other related software.

Getting started

Flashing the device

Natively the board only supports booting the platform firmware from SPI, the eMMC or a microSD card, see boot order. The platform firmware loaded from there (U-Boot, EDK2, ...) may then allow loading kernels from additional storage mediums or even the network, and they will have their own boot order.

The board can be booted by flashing your chosen operating system to a microSD card using another device and inserting the microSD card into the Quartz64, see the article Getting started. Flashing the eMMC is possible by booting an operating system from the microSD card and overwriting the eMMC from within the booted operating system, or by using the USB eMMC adapter.

Boot order

The hardware boot order of the Quartz64 is:

  1. SPI NOR flash
  2. SPI NAND flash
  3. eMMC
  4. microSD card

SoC and Memory Specifications

RK3566 icon.png

CPU Architecture

  • Quad-core ARM Cortex-A55@1.8GHz
  • AArch32 for full backwards compatibility with ARMv7
  • ARM Neon Advanced SIMD (single instruction, multiple data) support for accelerated media and signal processing computation
  • Includes VFP hardware to support single and double-precision operations
  • ARMv8 Cryptography Extensions
  • Integrated 32KB L1 instruction cache and 32KB L1 data cache per core
  • 512KB unified system L3 cache
  • TrustZone technology support
  • 22nm process, believed to be FD-SOI

GPU (Graphics Processing Unit) Capabilities

  • Mali-G52 2EE Bifrost GPU@800MHz
  • 4x Multi-Sampling Anti-Aliasing (MSAA) with minimal performance drop
  • 128KB L2 Cache configurations
  • Supports OpenGL ES 1.1, 2.0, and 3.2
  • Supports Vulkan 1.0 and 1.1
  • Supports OpenCL 2.0 Full Profile
  • Supports 1600 Mpix/s fill rate when at 800MHz clock frequency
  • Supports 38.4 GLOP/s when at 800MHz clock frequency

NPU (Neural Processing Unit) Capabilities

  • Neural network acceleration engine with processing performance of up to 0.8 TOPS
  • Supports integer 8 and integer 16 convolution operations
  • Supports the following deep learning frameworks: TensorFlow, TF-lite, Pytorch, Caffe, ONNX, MXNet, Keras, Darknet

System Memory

  • RAM Memory Variants: 2GB (SOQuartz only), 4GB, 8GB LPDDR4.

Network

  • 10/100/1000Mbps Ethernet
    • Easily sustains >910 Mbit/s in a --bidir (i.e. sending and receiving at the same time) iperf3 TCP test.
  • Wi-Fi 802.11 b/g/n/ac with Bluetooth 5.0 (optional on model A, built in on model B)

Storage

  • microSD - bootable, supports SDHC and SDXC, storage up to 2TB
  • USB
    • Model A: 2 USB 2.0 host ports, 1 USB 2.0 OTG port, 1 USB 3.0 host port
    • Model B: 1 USB 2.0 host port, 1 USB 2.0 OTG port, 1 USB 3.0 host port
  • one native SATA 3.0 6Gb/s Port (only on model A, shared with USB 3.0 host port) (removed in newer revisions due to electrical signalling issues it caused)
  • optional eMMC module from 8GB up to 128GB
  • 64 Mbit (8 MByte) SPI flash (Model B only), part number 25Q64DWZPIG in the schematic

eMMC Speeds

On a 64 GB eMMC module:

 $ sudo hdparm -tT /dev/mmcblk1 
 
 /dev/mmcblk1:
  Timing cached reads:   2368 MB in  2.00 seconds = 1184.46 MB/sec
  Timing buffered disk reads: 452 MB in  3.01 seconds = 149.98 MB/sec

Expansion Ports

  • HDMI
  • eDP - 4 lanes of 2.7Gbps, up to 2560x1600@60Hz (only on model A)
  • DSI - Display Serial Interface, 4 lanes MiPi, up to 1440P on model A, 2 lanes MiPi, up to 1080p on model B
  • CSI - CMOS Camera Interface, 4 lanes MiPi up to 8 mega pixel on model A, 2 lanes MiPi up to 5 mega pixel on model B
  • TP - Touch Panel Port, SPI with interrupt on model A
  • RTC - Real Time Clock Battery Connector
  • VBAT - Lithium Battery Connector with temperature sensor input on model A
  • Wi-Fi/BT Module Header - SDIO 3.0 and UART on model A, built-in Wi-Fi/BT Module on model B
  • 2x20 pins "Pi2" GPIO Header on model B, 2x10 pins GPO header on model A
  • PCIe x4 open ended slot on model A, m.2 slot on model B, one Gen2 lane due to SoC constraints
    • On Model A, the slot provides 10W of power for the 3.3V supply and however much power your 12V input power supply provides on the 12V supply

The PCIe implementation on the RK3566 is much more compatible with a wide range of devices compared to the one on the RK3399 used on the ROCKPro64. This means a lot more devices should work (excluding dGPUs due to a lack of cache snooping ability).

Combo PHYs

Rk3566 phy.png

Several of the I/O options on the RK3566 used in the Quartz64 are using the same I/O lines, meaning that they cannot be used at the same time. The above diagram illustrates how they are connected.

In particular, USB 3.0 and the SATA connector on the board are mutually exclusive, and the PCI-e 2.0 lane can be reconfigured into a second SATA port, though an adapter cable needs to be fashioned for this to be useful.

GPIO Pins (Quartz64 Model A)

Attention! GPIOs are 3.3V!

Assigned To Pin no. Pin no. Assigned To
3.3 V 1 2 5 V
I2C3_SDA_M0 a,b 3 4 5 V
I2C3_SCL_M0 a,b 5 6 GND
CPU_REFCLK_OUT 7 8 UART2_TX_M0_DEBUG
GND 9 10 UART2_RX_M0_DEBUG
SPI1_MOSI_M1 11 12 UART0_TX a
SPI1_MISO_M1 13 14 UART0_RX a
SPI1_CLK_M1 15 16 GND
SPI1_CS0_M1 17 18 SPDIF_OUT c
GND 19 20 3.3V

Notes

  1. can be a PWM pin
  2. pulled high to 3.3V through 2.2kOhm resistor
  3. low-pass filtered with cutoff of 220 MHz

Source: Page 28 of File:Quartz64 model-A schematic v1.0 20201215.pdf.

GPIO Pins (Quartz64 Model B)

Attention! GPIOs are 3.3V!

Interesting alternate pin configurations are listed in [brackets].

Assigned To Pin no. Pin no. Assigned To
3.3 V 1 2 5 V
[I2C3_SDA_M0] GPIO1_A0_3V3 3 4 5 V
[I2C3_SCL_M0] GPIO1_A1_3V3 5 6 GND
GPIO3_C4_3V3 7 8 UART2_TX
GND 9 10 UART2_RX
[SPI1_CS0_M1] GPIO3_A1_3V3 11 12 GPIO3_A3_3V3 [I2S3_SCLK_M0]
[I2S3_MCLK_M0] GPIO3_A2_3V3 13 14 GND
GPIO3_B0_3V3 15 16 GPIO3_B1_3V3
3.3V 17 18 GPIO3_B2_3V3
GPIO4_C3_3V3 19 20 GND
GPIO4_C5_3V3 21 22 GPIO3_C1_3V3 [SPI1_MOSI_M1]
GPIO4_C2_3V3 23 24 GPIO4_C6_3V3
GND 25 26 GPIO4_D1_3V3
I2C4_SDA_M0 27 28 I2C4_SCL_M0
GPIO3_B3_3V3 29 30 GND
GPIO3_B4_3V3 31 32 GPIO3_C2_3V3 [SPI1_MISO_M1]
[SPI1_CLK_M1] GPIO3_C3_3V3 33 34 GND
[I2S3_LRCK_M0] GPIO3_A4_3V3 35 36 GPIO3_A7_3V3
[SPDIF_TX_M0] GPIO1_A4_3V3 37 38 GPIO3_A6_3V3 [I2S3_SDI_M0]
GND 39 40 GPIO3_A5_3V3 [I2S3_SDO_M0]

Source: Page 24 of the board schematics.

Quartz64 Board Information, Schematics, and Certifications

Model "A"

Model "A" Baseboard Dimensions: 133mm x 80mm x 19mm

Input Power: DC 12V @ 3A 5.5mmOD/2.1mmID center-positive Barrel DC Jack connector

Quartz64 Model "A" SBC Schematic and PCB Board Resource:

Certifications:

  • Disclaimer: Please note that PINE64 SBC is not a "final" product and in general certification is not necessary. However, PINE64 still submit the SBC for FCC and CE certification and obtain the certificates to proof that SBC board is capable on passing the testing. Please note a final commercial product needs to performs its owns testing and obtains its owns certificates.
  • Quartz64 model-A CE Certificate
  • Quartz64 model-A FCC Certificate

Model "B"

Model "B" Baseboard Dimensions: 85mm x 56mm x 18.8mm

Input Power: DC 5V @ 3A 3.5mmOD/1.35mmID center-positive Barrel DC Jack connector

Quartz64 Model "B" SBC Schematic and PCB Board Resource:

Datasheets for Components and Peripherals

Rockchip RK3566 SoC information:

Rockchip PMU (Power Management Unit) Information:

LPDDR4 (200 Balls) SDRAM:

eMMC information:

SPI NOR Flash information:

E-ink Panel information:

LCD Touch Screen Panel information:

Ethernet PHY information:

Wi-Fi/BT module info:

IR LED:

Enclosure information:

Connector information:

Development efforts

Main Article: Quartz64 Development

Information and resources of the ongoing development effort for the Quartz64 can be found on the Quartz64 Development page, where the current status of various board functions can be found, and whether they have landed in upstream.

Enclosures

Note: Please expand this section with more cases known to work.

Model "A"

All enclosures that fit the ROCKPro64 should fit the Quartz64 Model "A", as the I/O has been laid out the same on purpose.

Model "B"

Troubleshooting

Stability/Boot Issues With Missing Battery Shunt

If there is no battery plugged into the board, the jumper labelled "ON/OFF_BATT" must be in place. If this is set wrong, stability issues such as failures to boot will occur. This affects model A only

No Ethernet Connectivity

Make sure the kernel is built with CONFIG_MOTORCOMM_PHY set to y. Building it as a module (m) and then relying on module auto-loading is unlikely to work, because if the generic PHY driver is built in it will bind to the PHY first, unless you include the motorcomm module in your initramfs.

Note: Starting with Debian's 6.1~rc3-1~exp1 kernel the module is included, but set to m and I (Diederik) have verified that it gets included in the initramfs and works on Model-A and Model-B with the Quartz64#Plebian images.

"Model A" Acrylic Case Doesn't Fit

The Quartz64 does not really fit onto the bottom plate of the Model A Acrylic Open Enclosure. This is because the "Mic" connector at the bottom of the board interferes with one of the posts. A workaround is to find out which post that is (you have a 50% chance of guessing it right, accounting for rotating the board) and then filing away the corner of the post pointing inwards by a few millimeters.

Quartz64-audio-jack-spacer-issue.jpg

An alternate solution may be to place plastic spacers with a smaller outer diameter in between the acrylic bottom plate posts and the SBC board.

No GPU Acceleration with Debian "Bullseye" Userland

Debian Bullseye ships a Mesa version that is too old to contain the required patches for the RK356x SoC's GPU. Upgrade to Bookworm.

Wireless Connectivity Doesn't Work

ROCKPro64 wireless module may have CYW43455 or CYW43456 chips on board (not sure if this is the same for Quartz64 model B). Both chips are supported by brcmfmac Wi-Fi driver and btbcm Bluetooth driver.

For CYW43455 drivers attempt to load /lib/firmware/brcm/brcmfmac43455-sdio.bin for Wi-Fi and /lib/firmware/brcm/BCM4345C0.hcd for Bluetooth. Corresponding firmware files for CYW43456 are /lib/firmware/brcm/brcmfmac43456-sdio.bin and /lib/firmware/brcm/BCM4345C5.hcd.

On Manjaro firmware files for both Bluetooth and Wi-Fi on CYW43456 on are provided by ap6256-firmware package (pacman -S ap6256-firmware).

However for CYW43455 wi-fi firmware is in the linux-firmware package and bluetooth is in the firmware-raspberrypi (pacman -S linux-firmware firmware-raspberrypi). linux-firmware package is missing device specific symlinks for quartz64-a. To create them execute:

# ln -s brcmfmac43455-sdio.bin /lib/firmware/brcm/brcmfmac43455-sdio.pine64,quartz64-a.bin
# ln -s brcmfmac43455-sdio.AW-CM256SM.txt /lib/firmware/brcm/brcmfmac43455-sdio.pine64,quartz64-a.txt 

As of 2022-10-19 device tree in mainline kernel for Quartz64 model A has wrong configuration for the Bluetooth driver. Patch is submitted to the LKML and accepted and included upstream in 6.1-rc7. It's possible to modify dtb file provided by the current kernel using device tree compiler to enable Bluetooth or perform make dtbs in the patched kernel tree to get updated dtb file (arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.dtb). Issue manifests itself with following errors in `dmesg`:

 command 0x0c03 tx timeout
 Bluetooth: hci0: BCM: Reset failed (-110)

How-To

Connect Debug UART

The easiest way to get debug output is to connect a 3.3V 1.5mbaud capable UART adapter to the board.

To connect it, connect the ground lead to pin 6, and the RX/TX leads to pins 8 and 10 (consider swapping them if you get no output, things are often mislabeled). These pins are "UART2" in the above GPIO table.

Open a serial terminal at 1500000 bauds, e.g.

$ picocom -b 1500000 /dev/ttyUSB0

Disable Heartbeat LED (Linux)

The flashing LED is called the "heartbeat LED", it blinks in a heart rhythm like fashion once the kernel is running. To disable it, you can run

# echo none > /sys/class/leds/user-led/trigger

On model A LED device is called "diy-led", not "user-led".

On a system with systemd, you can do this as soon as the system is ready to be logged in with a systemd unit like this:

[Unit]
Description=Turn off heartbeat LED
Wants=multi-user.target
After=multi-user.target

[Install]
WantedBy=multi-user.target

[Service]
Type=simple
ExecStart=sh -c 'echo none > /sys/class/leds/user-led/trigger'

Place it in /etc/systemd/system/user-led.service, and run

# systemctl daemon-reload
# systemctl enable user-led.service

Upon rebooting, you will now notice that the heartbeat LED will blink during boot-up, but stops blinking as soon as the multi-user target is reached (i.e. the user can log in).

SATA on model A

On model A USB 3.0 and SATA ports are using the same I/O line and can't be used simultaneously. By default USB 3.0 is enabled in Linux device tree and SATA is disabled. FDT modifications are required to turn SATA on.

Following script is tested on Manjaro but should work on the other distributions with minimal changes. Device tree compiler package usually provides fdtput command (on Manjaro run: pacman -S dtc)

# cp /boot/dtbs/rockchip/rk3566-quartz64-a.dtb /boot/dtbs/rockchip/rk3566-quartz64-a-sata.dtb
# fdtput -t s -v /boot/dtbs/rockchip/rk3566-quartz64-a-sata.dtb /usb@fd000000 status disabled
# fdtput -t s -v /boot/dtbs/rockchip/rk3566-quartz64-a-sata.dtb /sata@fc400000 status okay
# sed -i 's#^FDT /dtbs/rockchip/rk3566-quartz64-a.dtb$#FDT /dtbs/rockchip/rk3566-quartz64-a-sata.dtb#' /boot/extlinux/extlinux.conf
# systemctl reboot

Using a PCF8574 on Model A

See Quartz64 Model A using a PCF8574.

Using a battery on Model A

See Quartz64 Model A Using a battery.

Connecting a MIPI-DSI display

See Quartz64 connecting a MIPI-DSI display.

Building Mainline U-Boot

See Quartz64 Building U-Boot.

Frequently Asked Questions

Do I Need A Fan/What Heatsink Do I Need?

You don't need a fan. The 20mm medium heatsink for Model A is plenty enough. For Model B, the fan type heatsink will do fine.

Can This Run A Minecraft Server?

Yes! Sort of. Testing on an 8GB Model A with PaperMC, User:CounterPillow was able to out-row world generation in a boat with just one player online, but aside from the slow world gen (which can be pre-generated) the server handled things like TNT explosions and mobs fine. It'll probably do okay with 1-3 players.

Do I Need The 5A Power Supply For Model A?

You only need the 5A power supply for Model A if you plan on connecting hard disk drives to the 12V header on the board.

How Much Power Does It Consume?

For Model B, it's <2W in idle (powertop tunables not set), and <5W under full CPU load (stress-ng -c4). Model A will be similar as it's the same SoC.