Difference between revisions of "Pinecil"

From PINE64
Jump to navigation Jump to search
Line 48: Line 48:


* [https://files.pine64.org/os/Pinecil/Pinecil_firmware_20201115.zip Pinecil production firmware 20201115, thanks to Ralimtek]
* [https://files.pine64.org/os/Pinecil/Pinecil_firmware_20201115.zip Pinecil production firmware 20201115, thanks to Ralimtek]


== Pinecil tips ==
== Pinecil tips ==

Revision as of 07:35, 10 December 2020

PAGE UNDER CONSTRUCTION, INFO SUBJECT TO CHANGE

  • Pinecil Renders:

Pinecil Exploded Diagram ver 0.9.png


Pinecil-bb2-01.jpg

  • Pinecil Prototype:

PinecilPrototype.jpg

Specifications

  • Dimensions: 170mm with solder tip or 98mm without solder tip x 12.8mm x 16.2mm
  • Weight: 30g with solder tip, 20g without solder tip
  • CPU: GD32VF103TB 32-bit RV32IMAC RISC-V “Bumblebee Core” @ 108 MHz
  • Memory:
    • 128KB Flash
    • 32KB SRAM
  • DC in (only one of the following at a time):
    • 12V- 24V DC5525 Barrel Jack
    • USB-C 12-20V PD
    • QC3.0
    • Recommend operating voltage 12-21V, maximum rating at 24V

Pinecil board information, schematics and certifications

  • Pinecil breakout board: Pinecil-breakout-board-02.jpg


Firmware Image Releases


Pinecil tips

  • Default tip model TS-B2 accompany with Pinecil
  • Tip set 1 (left) & 2 (right): PinecilTipSets.jpg
  • Uses TS-100 compatible tips

Datasheets for components and peripherals


Development efforts

Project Homepage Project Source Implementations
Ralimtek https://ralimtek.com https://www.gitmemory.com/Ralim

How to update a firmware

(Method tested on Linux, should work on any OS where dfu-util works, instructions assumes you have dfu-util 0.9)

Warning: This potentially can brick your device. Do on your own risk!
Warning: Author of these instructions successfully dumped a firmware, bricked the device with a custom firmware and flashed stock dump back.


  1. Enter an update mode. For that plug USB cable while holding *-* button (button, that's closest to USB-C port)
  2. Make a firmware backup: dfu-util -d 28e9:0189 -a 0 -U ~/pinecil/internal.flash.stock -s 0x08000000
    1. 28e9:0189 -- USB Device ID (can be obtained from `lsusb` or `dfu-util -l` but in dfu-util output it might be hard to identify the Pinecil device)
    2. -a 0 -- selects what to flash. List of possible options can be obtained via `dfu-util -l`.
    3. `-U` -- specifies a mode. U is upload, which means that firmware will be downloaded and saved to file (yes, that's confusing, but it is what it is, feel free to verify that in a manual of your version of dfu-util). Command must be followed by a path to file where you want to save your firmware. dfu-util will refuse to dump firmware if you already have a file with that name.
    4. -s 0x08000000 -- specify the address in a flash from which dump will start. This can be obtained from `dfu-util -l`.
  3. Flash a new firmware: dfu-util -d 28e9:0189 -a 0 -D ~/pinecil/internal.flash.stock -s 0x08000000:mass-erase:force
    1. -D -- is a mode to Download firmware to the device (yes, that's confusing, but you indeed Upload from device and Download to device with dfu-util). That should follow the file with the firmware Same stock one from (1) used here on purpose.
    2. -s 0x08000000:mass-erase:force -- specified the address where to flash the file. `:mass-erase:force` is required to force-erase flash before updating firmware, otherwise you might have unpredictable results.