Difference between revisions of "Pinebook Pro"

From PINE64
Jump to navigation Jump to search
Line 140: Line 140:
''Step 5'': Detach microphone and speakers.
''Step 5'': Detach microphone and speakers.


The speakers and microphone don't have to be detached from the mainboard, but they need to be detached from the keyboard shell.  The microphones are held in place by tape, and the speakers have sticky sides.  The speakers are found obviously, but the microphones (two of) can be found between the battery and the hinge area.
The speakers and microphone don't have to be detached from the mainboard, but they need to be detached from the keyboard shell.  The microphones are held in place by tape, and the speakers have sticky sides.  The speakers are found obviously, but the microphones (two of) can be found between the battery and the hinge area. The microphones can be carefully pulled/wedged out of their position by a small screwdriver or pick.


''Step 6'': Remove mainboard and daughterboard.
''Step 6'': Remove mainboard and daughterboard.

Revision as of 22:31, 11 October 2021

User Guide

Introducing PineBook Pro

Pinebook Pro running Debian with MATE

The Pinebook Pro is a Linux and *BSD ARM laptop from PINE64

It is built to be a compelling alternative to mid-ranged Chromebooks that people convert into Linux laptops. It features an IPS 1080p 14″ LCD panel, a premium magnesium alloy shell, high capacity eMMC storage, a 10,000 mAh capacity battery, and the modularity that only an open source project can deliver.

It's compact and slim dimensions are 329mm x 220mm x 12mm (WxDxH).

Key features include: the RK3399 SOC; USB-C for data, video-out and power-in (3A 5V); privacy switches for the microphone, BT/WiFi module, and camera; and expandable storage via NVMe (PCIe x4) with an optional adapter.

The Pinebook Pro is equipped with 4GB LPDDR4 system memory, high capacity eMMC flash storage, and 128Mb SPI boot Flash. The I/O includes: 1 x micro SD card reader (bootable), 1 x USB 2.0, 1 x USB 3.0, 1 x USB type C Host with DP 1.2 and power-in, PCIe x4 for an NVMe SSD drive (requires an optional adapter), and UART (via the headphone jack by setting an internal switch).

The keyboard and touchpad both use the USB 2.0 protocol. The LCD panel uses eDP MiPi display protocol.

Many different Operating Systems (OS) are freely available from the open source community and partner projects. These include various flavors of Linux (Ubuntu, Debian, Manjaro, etc.) and *BSD.

Software and OS Image Downloads

Default Manjaro KDE Desktop Quick Start

When you first get your Pinebook Pro and boot it up for the first time, it'll come with Manjaro using the KDE desktop. The Pinebook Pro is officially supported by the Manjaro ARM project, and support can be found on the Manjaro ARM forums.

On first boot, it will ask for certain information such as your timezone location, keyboard layout, username, password, and hostname. Most of these should be self-explanatory. Note that the hostname it asks for should be thought of as the "codename" of your machine, and if you don't know what it's about, you can make something up (use a single word, all lower case, no punctuation; e.g. "pbpro").

After you're on the desktop, be sure to update it as soon as possible and reboot after updates are finished installing. If nothing appears when you click on the Networking icon in your system tray to connect to your Wi-Fi, ensure the Wi-Fi privacy switch is not disabled.

Pinebook Pro images

Under Pinebook Pro Software Release you will find a complete list of currently supported Operating System images that work with the Pinebook as well as other related software.

The list includes OS images and descriptions of:

Keyboard

The Pinebook Pro is available in two keyboard configurations: ISO and ANSI. Both the keyboard and touchpad in the Pinebook Pro use the USB 2.0 protocol and show up as such in xinput. The keyboard features function (Fn) keys in the F-key row, which include display brightness controls, sound volume, touchpad lock, and other functionality. There is also a custom PINE64 logo key that functions as Menu/Super key. It has also a secondary functionality for setting the privacy switches.

The keyboard firmware binary can be flashed from userspace using the provided open source utility.

Warning: DO NOT update the keyboard firmware before checking which keyboard IC your Pinebook Pro has. Some Pinebook Pro were delivered with a SH61F83 instead of a SH68F83. The SH61F83 can only be written 8 times, this will render the keyboard and touchpad unusable if this limit is reached when step-1 is flashed, see the Reddit SH61F83 thread. The keyboard IC corresponds to U23 on the top layer silkscreen of the main board. It is located under the keyboard flat flexible cable.

Documentation for the keyboard can be found in Datasheets for Components and Peripherals.

Typing special characters

The UK ISO Layout does not have dedicated keys for characters like the German umlauts (Ä,Ö,Ü, etc). Certain characters can still be generated by means of either key combinations or key sequences.

Character Key combination/sequence
Ä, Ö, Ü, ä, ö, ü [AltGr]+'[' followed by [A], [O], [U], [a], [o] or [u]
µ [AltGr]+[m]
Ø, ø [AltGr]+[O], [AltGr]+[o]
@ [AltGr]+[q] (as on the German layout)
ß [AltGr]+[s]
§ [AltGr]+[S]
° [AltGr]+[)]

Privacy Switches

There are three privacy switches mapped to the F10, F11 and F12 keys on the Pinebook Pro keyboard. They de/activate the following:

Privacy switch function and description
Combination Effect Description Notes
PINE64 logo key+F10 Microphone Privacy switch CAPs lock LED blinks. 2 blinks = enabled, 3 blinks = disabled
PINE64 logo key+F11 WiFi Privacy switch NUM lock LED blinks. 2 blinks = WiFi enabled / privacy switch disabled, 3 blinks = WiFi disabled / privacy switch enabled. Re-enabling requires reboot (or a command line hack to bind/unbind).
PINE64 logo key+F12 Camera privacy switch CAPs lock and NUM lock LEDs blink together. 2 blinks = enabled, 3 blinks = disabled Can use tools like lsusb to detect camera's presence. If not detected, check privacy switch.

(Press the PINE64 logo key plus F10/F11/F12) for 3 seconds)

The keyboard operates on firmware independent of the operating system. It detects if one of the F10, F11 or F12 keys is pressed in combination with the Pine key for 3 seconds. Doing so disables power to the appropriate peripheral, thereby disabling it. This has the same effect as cutting off the power to each peripheral with a physical switch. This implementation is very secure, since the firmware that determines whether a peripheral gets power is not part of the Pinebook Pro’s operating system. So the power state value for each peripheral cannot be overridden or accessed from the operating system. The power state setting for each peripheral is stored across reboots inside the keyboard's firmware flash memory.

Basic summary of replacing keyboard

This guide is very basic and should be fleshed out with pictures. There just isn't a list of steps anywhere else yet.

Step 0: If changing from ISO keyboard to ANSI keyboard, or vice versa, be sure to have a system capable of running the firmware updater that you can access either remotely or with a USB keyboard beyond the internal keyboard, as the firmware for each is very different and keys won't work correctly. See https://forum.pine64.org/showthread.php?tid=8407 (and for NetBSD, https://forum.pine64.org/showthread.php?tid=8716).

Step 1: The remove back back panel.

There are 10 screws on the back that must be removed, and the back panel detached. The speakers may remain attached via glue to the case and should be carefully pried off. When this is done, taking photos of how everything looks now can help put it all back together later.

Step 2: Places to unscrew.

There are 3 items screwed into the keyboard frame that must be removed. There are 2 large screws for daughter board, 3 large screws and 1 small screw for mainboard, and 4 screws for battery. Be sure to not lose them.

Step 3: Remove the battery.

Once the battery screws are removed, it should be unplugged from the mainboard and removed. Note that there are two unconnected cables lying around, that should remain unconnected. They are used when the battery is disconnected entirely.

Step 4: Unplug the ribbon cables.

There are several ribbon cables. To remove, flip up the tab and gentle pull the ribbon out.

  • One cable runs from the mainboard to the daughterboard underneath the battery. Detach from both ends. With the battery removed, detach from keyboard shell, and set aside for the new keyboard shell.
  • One cable runs between the touchpad and the mainboard. Detach from both ends, and also set aside.
  • One cable runs between the keyboard and the mainboard. This one remains attached to the keyboard and only needs to be detached from the mainboard.
  • One cable from the LCD attaches near the lid hinge. It should be just unplugged.

Step 5: Detach microphone and speakers.

The speakers and microphone don't have to be detached from the mainboard, but they need to be detached from the keyboard shell. The microphones are held in place by tape, and the speakers have sticky sides. The speakers are found obviously, but the microphones (two of) can be found between the battery and the hinge area. The microphones can be carefully pulled/wedged out of their position by a small screwdriver or pick.

Step 6: Remove mainboard and daughterboard.

At this point, the mainboard and daughterboards should be removed. When unscrewed (see Step 2) they should pull out fairly easily. Put them aside (including microphones and speakers if left attached.)

Step 7: Detach the LCD panel.

Step 2 didn't tell you, there are 6 more screws to remove here, 3 for each of the hinges. Unscrew these and the LCD panel will be able to be removed. You may have to jiggle or move the hinges for this. When detached, be sure to place the LCD panel such that the display is protected.

Step 8: Try Not To Break Your Touchpad, or, How I Learned To Love Things That Bend

NOTE This section really feels like you're going to break something.

The touchpad is glued to the keyboard shell and it's glued well. There are two places it is glued to. If you can, only the middle must be force-detached. You will think you're going to break it. Gently apply increasing force until the glue begins to detach (you will hear a crackle as it comes off), and continue very slowly until the whole thing is detached. This may take minutes due to that feeling you're going to break it.

Step 9: Over the hill, touchpad goes into new shell.

In the new keyboard shell put the touchpad back where it was, hopefully the glue will remain sufficiently attached. If there is a glue issue, this guide unfortunately has no advice currently.

Step 10: Reattach the LCD panel.

The LCD panel should slot back into the keyboard frame, the same way it came out. If the hinges were moved, they should be *very* *gently* closed such that the LCD panel and keyboard closed like normal for the remaining steps.

Step 11: Tape it out.

Move any tape from the old keyboard shell to the new one. These items protect the mainboard and daughterboard, and keep various wires in their right place. Some are grey and some are black. For tape that holds the speakers, microhones, or their cables in place, do not reattach yet.

Step 12: Board install.

Install the mainboard, the daughtboard, and their connecting ribbon cable. Be sure to put the boards in place, 2 large flat screws for the daughterboard, 3 large flat screws and one small screw for the mainboard, before attempting to place the ribbon.

Step 13: Microphone and speaker install.

Reattached the microphones and speakers to their respective areas, making sure that both are properly oriented - the speaker "out" faces up, and the microphone cables as connected must face up (these are opposite directions.)

Step 14: Reattach other ribbon cables.

The LCD panel, keyboard and touchpad ribbon cables should be reattached. Make sure the flap is open, insert the ribbon into the slot (a portion of the cable will disappear), and push the flap down. The cable should not be easy to pull out.

Step 15: Reattach the battery, and final re-tape.

The battery should be installed with the 4 screws holding it in place, and the connector attached to the mainboard. Be sure to keep the two other cables remain unconnected. Ensure all wires and other tapes are held in place.

Step 16: Reattach the back panel.

Put the back panel back on, and reattach the 10 screws.

Step 17: If you changed from ISO to ANSI or from ANSI to ISO, you'll need to update your firmware now. See the links in Step 0 above.

Touchpad (trackpad)

Documentation for the touchpad can be found in Datasheets for Components and Peripherals. It is the only component of the Pinebook Pro held in place with strong adhesive tape. Here are some of its features:

  • 2 actuating buttons.
  • multi-touch functionality.
  • A matte finish that your finger can slide along easily.
  • A reasonable size (96mm × 64mm; diagonal: 115.378mm or 4.542”).

Troubleshooting

If you are having trouble using 2 fingers to scroll or emulate the click of a mouse's right-button, then try these solutions:

  • Update the firmware.
  • Keep your 2 fingers spread apart rather than close together.
  • Individual programs might need to be configured specially.
  • For smooth scrolling and gestures under X-Windows, Firefox should be launched with with the following environment variable assignment:
MOZ_USE_XINPUT2=1
  • Experiment with other settings, via X-Windows Configuration or some other system preferences; for example, you could disable double-finger scrolling, and instead enable scrolling by sliding one finger along the edge of the touchpad.

Firmware

The touchpad controller is connected to the keyboard controller. All touchpad events go through the keyboard controller and it's software, then to the keyboard controller's USB port. Note that the touchpad does have separate firmware, (which has to be written through the keyboard controller). The touchpad vendor’s firmware binary can be flashed from userspace using the following open source command-line utility:

Naturally, forks have begun to appear:

  • Jack Humbert’s fork
  • Dragan Simic’s fork. This one has recently delivered a much improved firmware from the vendor, which greatly improves the control of the cursor (see this thread for discussion); before installing this update, consider resetting to the defaults any configuration of your touchpad.

Every Pinebook Pro produced before September 2021 should have its keyboard and touchpad firmware updated.

Warning: DO NOT update the touchpad firmware before checking which keyboard IC your Pinebook Pro has. Some Pinebook Pro were delivered with a SH61F83 instead of a SH68F83. The SH61F83 can only be written 8 times, this will render the keyboard and touchpad unusable if this limit is reached when step-1 is flashed. See Reddit SH61F83 thread. The keyboard IC corresponds to U23 on the top layer silkscreen of the main board. It is located under the keyboard flat flexible cable.

Before updating any firmware, your Pinebook Pro should be either fully charged or, preferably, running from mains. This utility will be writing data to chips on the keyboard and touchpad, so a loss of power during any stage of the update can result in irrecoverable damage to your touchpad or keyboard.

The scripts ought to work on all OSs available for the Pinebook Pro. Some OSs may, however, require installation of relevant dependencies. The instructions below assume a Debian desktop. To install these dependencies, newer Pinebook Pro models that come with Manjaro will require a different command.

There are two keyboard versions of the Pinebook Pro: ISO and ANSI. You need to know which model you have prior to running the updater. Firmware update steps for both models are listed below.

What you will need:

  • Connection to WiFi (for getting dependencies).
  • Your Pinebook Pro fully charged or running from mains power.
  • An external USB keyboard & mouse (or access to the Pinebook Pro via SSH. Please note that for some configurations, the SSH service might not be available without first having logged in once; in this case, you will definitely want at least an external keyboard).

ISO Model

From the terminal command line:

git clone https://github.com/ayufan-rock64/pinebook-pro-keyboard-updater
cd pinebook-pro-keyboard-updater
sudo apt-get install build-essential libusb-1.0-0-dev xxd
make

Step 1

cd pinebook-pro-keyboard-updater
sudo ./updater step-1 iso
sudo poweroff # do not use 'reboot'

Step 2 (after booting)

cd pinebook-pro-keyboard-updater
sudo ./updater step-2 iso
sudo poweroff # do not use 'reboot'

ANSI Model

Note: Running step 1 on the ANSI keyboard model will make the keyboard and touchpad inaccessible until step 2 is ran, so an external keyboard must be connected to complete the update on this model!

From the terminal command line:

git clone https://github.com/ayufan-rock64/pinebook-pro-keyboard-updater
cd pinebook-pro-keyboard-updater
sudo apt-get install build-essential libusb-1.0-0-dev xxd
make

Step 1

cd pinebook-pro-keyboard-updater
sudo ./updater step-1 ansi
sudo poweroff # do not use 'reboot'

Step 2 (after booting)

cd pinebook-pro-keyboard-updater
sudo ./updater step-2 ansi
sudo poweroff # do not use 'reboot'

When done, if some of the keys produce incorrect characters, please check your OS’s language settings. For ANSI users, the default OS may have shipped with English UK as the default language; you can change it to English US if desired.

Revised Firmware

In addition, you might consider using revised firmware data; this is one final step that should not require a reboot:

Step 3: ISO (after booting)

sudo ./updater flash-kb firmware/default_iso.hex

Step 3: ANSI (after booting)

sudo ./updater flash-kb firmware/default_ansi.hex

X-Windows Configuration

Before making adjustments, consider updating the firmware; reset your adjustments before updating the firmware, so that your adjustments do not interfere with new functionality.

Some forum members have found that an adjustment to X-Windows will allow finer motion in the touchpad. If you use the Synaptic mouse/touchpad driver, use this command to make the change live:

synclient MinSpeed=0.25

You may experiment with different settings, but 0.25 was tested as helping noticeably.

To make the change persist across reboots, change the file /etc/X11/xorg.conf similar to below:

    Section "InputClass"
        Identifier "touchpad catchall"
        Driver "synaptics"
        MatchIsTouchpad "on"
        MatchDevicePath "/dev/input/event*"
        Option "MinSpeed" "0.25"
    EndSection

The line Option "MinSpeed" "0.25" is the change.

Another forum user built on the above settings a little, and have found these to be very good:

synclient MinSpeed=0.25
synclient TapButton1=1
synclient TapButton2=3
synclient TapButton3=2
synclient FingerLow=30
synclient PalmDetect=1
synclient VertScrollDelta=64
synclient HorizScrollDelta=64

FingerLow has the same value as 'FingerHigh' in one config (30). It is believed to help reduce mouse movement as you lift your finger, but it's unknown whether synaptic works like this. You may find this config to be comfortable for daily use.

TabButton allows to just tab the touchpad instead of physically pressing it down (to get this click noise).

The right mouse click is emulated by tapping with two fingers on the touchpad. If you feel that this is not very responsive you can try this value:

 synclient MaxTapTime=250 

Some users may encounter an issue with the mouse jumping when typing when using libinput driver (has not been test with synaptic) due to their hand hitting the touchpad which can be fixed by updating the xorg settings to disable it while typing. One can disable the touchpad while typing by setting the below option in the xorg config simliar to the previou example.

        Option "DisableWhileTyping" "on" 

The setting can be verified by using the xinput command to first list the devices and then listing the properties for the Touchpad device. Exact commands to check this have been omitted for save of brevity. If DisableWhileTyping is shown enabled but does not appear to be working the issue may be due to the fact that the keyboard is connected to a USB bus which causes it to be seen as a external keyboard. To resolve this one can add the config below which sets the keyboard to internal to ensure the DisableWhileTyping works properly.

You will need to edit /etc/libinput/local-overrides.quirks and add the following lines:

[Serial Keyboards]
MatchUdevType=keyboard
MatchBus=usb
AttrKeyboardIntegration=internal

Once X11 is restarted the new setting should now take effect and you will no longer be able to use the touchpad while typing which will mostly eliminate the mouse jumping issue.

Power Supply

  • Input Power: 5V DC @ 3A
  • Mechanical: 3.5mm OD / 1.35mm ID, Barrel jack
  • USB-C 5V, 15W PD quickcharge
  • Only use one power input at a time, barrel jack OR USB-C

LEDs

In total, there are four LEDs on the Pinebook Pro, three of which are placed in the top-left side of the keyboard, and one near the barrel port:

  1. The red LED next to the barrel port indicates charging, in three ways. First, it will illuminate steadily when either the factory power supply or a USB Type-C charger is connected to the Pinebook Pro, and the battery is getting charged. Second, if the battery is at 100%, the LED will remain turned off regardless of the connected power input; however, this is rather rarely achieved. Third, this LED will flash at 0.5 Hz if there are any problems that prevent charging, such as the battery becoming too hot.
  2. The power indicator LED, above the keyboard, supports three different colors: green, amber and red. It is also capable of flashing to indicate eMMC activity. In the default Debian with MATE build, green LED means power and red means suspend (amber is unused).
  3. The green NumLock LED, above the keyboard.
  4. The green CapsLock LED, above the keyboard.

The NumLock and CapsLock LEDs serve their usual purposes on a keyboard, but they also have a secondary function. When the privacy switches get activated they blink to confirm that the switch has been activated.

Webcam

You can use Cheese to test the Camera functionality
  • Streaming video resolutions supported, (uncompressed):
    • 320 x 240
    • 640 x 480
    • 800 x 600
    • 1280 x 720
    • 1600 x 1200
  • Still frame resolutions supported:
    • 160 x 120
    • 176 x 144
    • 320 x 240
    • 352 x 288
    • 640 x 480
    • 800 x 600
    • 1280 x 720
    • 1600 x 1200

Microphones

While it has been said that some Pinebook Pro units contain only one microphone despite having two labeled microphone holes on the outer casing, other units do indeed contain two microphones. It is presently unclear which batches have either configuration; units from the initial community batch of 1000 units (following the initial 100) are believed to contain two, populating both labeled holes.

The wires leading to both microphones connect to the mainboard with a small white plastic connector, located directly adjacent to the ribbon cable attachment point for the keyboard interface.

Microphones not working?

If pavucontrol input doesn't show microphone activity try changing the privacy switches. If the switches are in the correct place and microphone input isn't working you can run alsamixer from the command line, hit F6 and select the es8316, hit F4 to get to the capture screen, select the bar labeled ADC, increase the gain to 0dB, change the audio profile in pavucontrol to another one with input. Additionally you may want to modify ADC PGA to get the levels to where you want them. If that still hasn't fixed it you may want to check that the microphone connector is plugged in (see the section Technical Reference).

Bluetooth and WiFi

The Pinebook Pro's AP6256 wireless module

Hardware Overview

The Pinebook Pro contains an AMPAK AP6256 wireless module to provide Wi-Fi (compliant to IEEE 802.11ac) and Bluetooth (compliant to Bluetooth SIG revision 5.0). The module contains a Broadcom transceiver IC, believed to be the BCM43456, as well as the support electronics needed to allow the Wi-Fi and Bluetooth modes to share a single antenna.

The wireless module interfaces with the Pinebook Pro’s system-on-chip using a combination of three interfaces: Bluetooth functionality is operated by serial UART and PCM, while the Wi-Fi component uses SDIO. It is unknown if the module’s Bluetooth capabilities are usable under operating systems that do not support SDIO.

The module’s RF antenna pin is exposed on the mainboard via a standard Hirose U.FL connector, where a coaxial feedline links it to a flexible adhesive antenna situated near the upper right corner of the Pinebook Pro’s battery. As the RF connector is fragile and easily damaged, it should be handled carefully during connection and disconnection, and should not be reconnected frequently.

Issues

Problems have been reported with the Wi-Fi transceiver’s reliability during extended periods of high throughput, especially on the 2.4 GHz band. While the cause of this has yet to be determined, switching to the 5 GHz band may improve stability.

Since the Bluetooth transceiver shares both its spectrum and antenna with 2.4 GHz Wi-Fi, simultaneous use of these modes may cause interference, especially when listening to audio over Bluetooth. If Bluetooth audio cuts out frequently, switching to the 5 GHz band – or deactivating Wi-Fi – may help.

Wi-Fi Capabilities

Wi-Fi on the Pinebook Pro is capable of reaching a maximum data transfer rate of approximately 433 megabits per second, using one spatial stream. The transceiver does not support multiple spatial streams or 160-MHz channel bandwidths.

The Wi-Fi transceiver supports the lower thirteen standard channels on the 2.4 GHz band, using a bandwidth of 20 MHz. At least twenty-four channels are supported on the 5 GHz band, spanning frequencies from 5180 to 5320 MHz, 5500 to 5720 MHz, and 5745 to 5825 MHz, with bandwidths of 20, 40, or 80 MHz.

Maximum reception sensitivity for both bands is approximately -92 dBm. The receiver can tolerate input intensities of no more than -20 dBm on the 2.4 GHz band, and no more than -30 dBm on the 5 GHz band. Maximum transmission power is approximately +15 dBm for either band, falling further to approximately +10 dBm at higher data transfer rates on the 5 GHz band.

With current available drivers and firmware, the Wi-Fi interface supports infrastructure, ad-hoc, and access-point modes with satisfactory reliability. Monitor mode is not presently supported. Wi-Fi Direct features may be available, but it is unclear how to make use of them under Linux.

Be aware that Linux userspace utilities, such as iw, may report inaccurate information about the capabilities of wireless devices. Parameter values derived from vendor datasheets, or direct testing, should be preferred to the outputs of hardware-querying tools.

Bluetooth Capabilities

Bluetooth data transfer speeds have an indicated maximum of 3 megabits per second, but it is unclear what practical data rates can be expected. Audio streaming over Bluetooth is functioning normally, as is networking. Bluetooth Low-Energy functions, such as interacting with Bluetooth beacons, have not yet been tested conclusively.

The Bluetooth transceiver supports all 79 channel allocations, spanning frequencies from 2402 MHz to 2480 MHz. Reception sensitivity is approximately -85 dBm, with a maximum tolerable reception intensity of -20 dBm. Bluetooth transmission power is limited to +10 dBm.

Disabling Bluetooth

To disable Bluetooth under Linux once:

sudo rfkill block bluetooth

To confirm if Bluetooth under Linux is disabled:

rfkill

To disable Bluetooth on boot (note: for distributions such as Manjaro XFCE see the step below):

sudo systemctl enable rfkill-block@bluetooth

To disable Bluetooth on certain distributions, such as Manjaro XFCE, right click on the Bluetooth panel icon, select plugins, then PowerManager, then configuration and then deselect the auto power on option

LCD Panel

  • Model: BOE NV140FHM-N49
  • 14.0" (35.56 cm) diagonal size
  • 1920x1080 resolution
  • 60 Hz refresh rate
  • IPS technology
  • 1000:1 contrast
  • 250 nit brightness
  • 63% sRGB coverage
  • 6-bit color
  • 30-pin eDP connection

Some people have tested hardware video decode using the following;

ffmpeg -benchmark -c:v h264_rkmpp -i file.mp4 -f null -

External ports list

Here are a list of the external ports. See Technical Reference - Expansion Ports for port specifications.

  • Left side
    • Barrel jack for power, (with LED)
    • USB 3, Type A
    • USB 3, Type C
  • Right side
    • USB 2, Type A
    • Standard headset jack
    • MicroSD card slot

Using the UART

Pinout of the serial adapter. Swapping the tx and rx around from this also works and is more traditional. See the official Pine64 document.

UART output is enabled by flipping the UART switch to the ON position (item 9). To do so you need to remove the Pinebook Pro's bottom cover - please follow proper disassembly and reassembly protocol. The OFF position is towards the touchpad, the ON position is towards the display hinges.

With the UART switch in the ON position, console is relayed via the audiojack and the laptop's sound is turned OFF. Please ensure that you are using a 3.3 V interface (such as the CH340, FTDI-232R, or PL2303, which are sold in both 3.3 V and 5 V variants) to avoid damage to the CPU. Older version of the serial console cable sold by Pine64 uses wrong voltage level and should not be used; see this forum thread for further information. Recent version of the same cable uses the right voltage level.

Insert the USB plug of the cable into an open USB port on the machine which will monitor, ensuring that the audio jack of the serial cable is be fully inserted into the Pinebook Pro audio port. Run the following in a terminal:

$ lsusb

you should find a line similar to this:

Bus 001 Device 058: ID 1a86:7523 QinHeng Electronics HL-340 USB-Serial adapter

Serial output should now be accessible using screen, picocom or minicom (and others). Examples:

screen /dev/ttyUSB0 1500000

picocom /dev/ttyUSB0 -b 1500000

minicom -D /dev/ttyUSB0 -b 1500000

Old versions of U-Boot do not use the UART for console output. The console function is activated by the Linux kernel. Thus, if you use a non-Pinebook Pro Linux distro and want the UART as a console, you have to manually enable it.

Using the optional NVMe adapter

The optional NVMe adapter allows the use of M.2 cards that support the NVMe standard, (but not SATA standard). The optional NVMe M.2 adapter supports M & M+B keyed devices, in both 2242 & 2280 physical sizes, the most common ones available. In addition, 2230 & 2260 are also supported, though NVMe devices that use those sizes are rare.

Once you have fitted and tested your NVMe drive, please add a note to this page Pinebook Pro Hardware Accessory Compatibility to help build a list of tried and tested devices.

Please see a separate section that describes reported issues with the NVMe drives in PineBook Pro.

Installing the adapter

The V2.1-2019-0809 SSD adapter that shipped with the initial Pinebook Pro batches had significant issues. A repair kit will be shipped to address those issues. (If necessary, it can be modified to work. There is an unofficial tutorial on the forums describing these modifications.)

The updated SSD adapter, labeled V2-2019-1107, takes into account the prior problems with touchpad interference. New orders as of Feb. 22nd, 2020 will be the updated adapter.

This is the link to the Pinebook Pro accessories in the store: [[1]]

Actual installation instructions are a work in progress. Unofficial instructions for installing V2-2019-1107 can be found here.

Post NVMe install power limiting

Some NVMe SSDs allow reducing the maximum amount of power. Doing so may reduce the speed, but it may be needed in the Pinebook Pro to both improve reliability at lower battery levels. And to reduce power used, to maintain battery life. Here are the commands to obtain and change the power settings. The package 'nvme-cli' is required to run these commands. The example shows how to find the available power states, and then sets it to the lowest, non-standby setting, (which is 3.8 watts for the device shown);

$ sudo nvme id-ctrl /dev/nvme0
NVME Identify Controller:
...
ps    0 : mp:9.00W operational enlat:0 exlat:0 rrt:0 rrl:0
         rwt:0 rwl:0 idle_power:- active_power:-
ps    1 : mp:4.60W operational enlat:0 exlat:0 rrt:1 rrl:1
         rwt:1 rwl:1 idle_power:- active_power:-
ps    2 : mp:3.80W operational enlat:0 exlat:0 rrt:2 rrl:2
         rwt:2 rwl:2 idle_power:- active_power:-
ps    3 : mp:0.0450W non-operational enlat:2000 exlat:2000 rrt:3 rrl:3
         rwt:3 rwl:3 idle_power:- active_power:-
ps    4 : mp:0.0040W non-operational enlat:6000 exlat:8000 rrt:4 rrl:4
         rwt:4 rwl:4 idle_power:- active_power:-

$ sudo nvme get-feature /dev/nvme0 -f 2
get-feature:0x2 (Power Management), Current value:00000000
$ sudo nvme set-feature /dev/nvme0 -f 2 -v 2 -s
set-feature:02 (Power Management), value:0x000002

Some NVMe SSDs don't appear to allow saving the setting with "-s" option. In those cases, leave off the "-s" and use a startup script to set the non-default power state at boot.
If you want to test performance without saving the new power setting semi-permanantly, then leave off the "-s" option.

There is another power saving feature for NVMes, APST, (Autonomous Power State Transitions). This performs the power saving & transitions based on usage. To check if you have a NVMe SSD with this feature;

$ sudo nvme get-feature -f 0x0c -H /dev/nvme0

Information for this feature, (on a Pinebook Pro), is a work in progress.

Using as data drive

As long as the kernel in use has both the PCIe and NVMe drivers, you should be able to use a NVMe drive as a data drive. It can automatically mount when booting from either the eMMC or an SD card. This applies to Linux, FreeBSD, and Chromium, using the normal partitioning and file system creation tools. Android requires testing.

Using as OS root drive

The SoC does not include the NVMe boot code, so the NVMe is not in the SoC's boot order. However, using the U-Boot update script from the mrfixit2001 Debian or Arglebargle's modified script, and the modified u-boot images provided by forum user pcm720, you can now add support to boot from an NVMe drive. Binary images are useable with SD, eMMC, and SPI flash. For OS images using the mainline kernel, there are a few variants of U-Boot available that also support NVMe as the OS drive. Though these may require writing the U-Boot to the SPI flash for proper use of the NVMe as the OS drive.

The current boot order, per last testing, for this modified U-Boot is:

  • MicroSD
  • eMMC
  • NVMe

For more information, please refer to the forum post.

It is also possible to initially boot off an eMMC or SD card, then transfer to a root file system on the NVMe. Currently, it is necessary to have the U-Boot code on an eMMC or SD card. (A forum member posted here about using a modified version of U-Boot with NVMe drivers, that uses /boot and / off the NVMe drive. So this may change in the future.)

Please see Bootable Storage.

Caring for the PineBook Pro

Bypass Cables

The mainboard features two (disconnected by default) bypass cables that are only to be used with the battery disconnected. The female (10) male (6) ends of the bypass cables can be connected to provide power to the mainboard if you need to run the laptop without a battery. Please refer to this engineering notice.

Note that despite the bypass cable being a two conductor cable, it is only used as one. Both wires being soldered together on either side is normal!

Warning: Do not connect the bypass cables with the battery connected. Using the bypass cables with the battery connected can permanently damage the computer.

Pinebook Service Step-by-Step Guides

Under Service Guides for Pinebook you can find instructions guides concerning disassembly of:

  • The installation process on Pinebook Pro similar to 14" Pinebook
  • The installation process is the reverse order of removal guide:
    • 14″ Pinebook Lithium Battery Pack Removal Guide
    • 14″ Pinebook LCD Panel Screen Removal Guide
    • 14″ Pinebook eMMC Module Removal Guide

Using the SPI flash device

See Pinebook Pro SPI for details.

The Pinebook Pro comes with a 128Mbit, (16MByte), flash device suitable for initial boot target, to store the bootloader. The SoC used on the Pinebook Pro boots from this SPI flash device first, before eMMC or SD card. At present, April 19, 2020, the Pinebook Pros ship without anything programmed in the SPI flash device. So the SoC moves on to the next potential boot device, the eMMC. ARM/ARM64 computers do not have a standardized BIOS, yet.

Here is some information on using the SPI flash device:

  • You need the kernel built with SPI flash device support, which will supply a device similar to: code>/dev/mtd0
  • The Linux package below, will need to be available: mtd-utils
  • You can then use this program from the package to write the SPI device: flashcp <filename> /dev/mtd0

Even if you need to recover from a defective bootloader written to the SPI flash, you can simply short pin 6 of the SPI flash to GND and boot. This will render the SoC bootrom unable to read from the SPI flash and have it fall back to reading the bootloader from other boot media like the eMMC or Micro SD card.

The procedures described above are a lot less risky than attaching an external SPI flasher and do not require any additional hardware. At present, April 19th, 2020, there is no good bootloader image to flash into the SPI flash device. This is expected to change, as there are people working on issue.

Software tuning guide

Details on how to get the most out of a Pinebook Pro & its RK3399 SoC.

Customizing the Pinebook Pro's default Manjaro KDE system

Watching DRM content (Netflix, etc.)

Most paid online streaming services use Widevine DRM to make their content more difficult to pirate. Widevine is not directly supported on Manjaro KDE, however it is still possible to watch DRM content via the "chromium-docker" package which downloads a 32-bit ARM container and installs Chromium with Widevine inside of that. While not space-efficient, or efficient in general, it's the recommended solution for watching this content on your Pinebook Pro. You can install this package with:

sudo pacman -Sy chromium-docker

Checking GPU capabilities

To see what versions of OpenGL and OpenGL ES are supported by the Pinebook Pro, what driver is in use, and what version of the driver is loaded, install the "mesa-demos" package with:

sudo pacman -Sy mesa-demos

And then run:

glxinfo | grep OpenGL

This will give detailed information about your graphics card and driver, useful for debugging.

Better GPU compatibility and performance

For better graphics performance, you may install the "mesa-git" package, built and supplied in the Manjaro ARM repos. This lets you bring in the latest features, optimizations, and bugfixes for the graphics driver used by the Pinebook Pro. Installation is as simple as:

pacman -Sy mesa-git

Then you may reboot to load the newer driver.

With Mesa 20.2 there is no longer much reason to use this over the standard mesa package, and applications may occasionally break with mesa-git.

Reporting bugs to the Mesa project will help make sure any problems are quickly fixed.

OpenGL 3.3 support

By default, with the current state of the Panfrost GPU driver, the Pinebook Pro supports OpenGL 2.1 and OpenGL ES 3.0. If you want to use OpenGL 3.3, you need to set the system-wide environment variable, open the /etc/environment file with:

kate /etc/environment

And then at the bottom of the file, on a new line, add:

PAN_MESA_DEBUG="gl3"

Then save the file, entering your password when prompted, and reboot the system. When you check your GPU capabilities, it should report OpenGL 3.3 and applications that rely on it should function properly. Note that GL 3.3 support is incomplete and some rendering features do not work yet, notably geometry shaders.

Install Anbox on Pinebook Pro Manjaro 20.10

Youtube video on installing Anbox on Pienbook Pro Manjaro Build 20.10 by LivingLinux

Customizing the Pinebook Pro's previously-default Debian system

Here are some hints on what you can do to customize the Pinebook Pro's previous factory image (aka mrfixit2001 debian build)

Initial user changes, password, name, etc

When you first get your Pinebook Pro, you should consider setting strong passwords and making the default account your own.

  • Reboot (this is just to ensure all background processes belong to the user are not running... there are other ways to achieve this but this way is easy)
  • Once the machine reboots press Alt-Ctrl-F1 to bring up a text terminal
  • Login as root (login: root, password: root)
  • Set a strong password for the root user using the following command and it's prompts:
# passwd (and follow prompts)
  • Rename the rock user to your prefered username (replace myself with whatever you like):
# usermod -l myself -d /home/myself -m rock
  • Rename the rock group to match your preferred username:
# groupmod -n myself rock
  • Put your name in the account, (replace "John A Doe" with your name):
# chfn -f "John A Doe" myself
  • Set a strong password for the normal user:
# passwd myself
  • Log out of the text terminal:
# logout
  • Press Alt-Ctrl-F7 to go back to the login screen and then login as the normal user
  • Open text terminal to fix login error: "Configured directory for incoming files does not exist";
$ blueman-services

Select "Transfer" tab and set "Incoming Folder" to myself OR If adduser is in distro, this is MUCH easier sudo adduser $USER ,, fill out requested data Then,, sudo adduser $USER $GROUP,,, 1 group at a time To see which groups to add,,, id $USER, id rock

Changing the default hostname

Debian 9 has a command to allow you to change the hostname. You can see the current settings using;

$ sudo hostnamectl
   Static hostname: Debian-Desktop
         Icon name: computer
        Machine ID: dccbddccbdccbdccbdccbdccbdccbccb
           Boot ID: ea99ea99ea99ea99ea99ea99ea99ea99
  Operating System: Debian GNU/Linux 9 (stretch)
            Kernel: Linux 4.4.210
      Architecture: arm64

To change, use this, (with "My_Hostname" used as the example);

$ sudo hostnamectl set-hostname My_Hostname

Whence done, you can re-verify using the first example.

Then you should backup and edit your /etc/hosts entry's name;

$ sudo cp -p /etc/hosts /etc/hosts.`date +%Y%m%d`
$ sudo vi /etc/hosts
127.0.0.1	localhost
127.0.0.1	My_Hostname
::1		localhost ip6-localhost ip6-loopback
fe00::0		ip6-localnet
ff00::0		ip6-mcastprefix
ff02::1		ip6-allnodes
ff02::2		ip6-allrouters
127.0.1.1       linaro-alip

Disable Chromium browser's prompt for passphrase & password storage

Perform the following steps:

  • On the tool bar, hover over the Chromium icon
  • Using the right mouse button, select Properties
  • In the Command: line section, add --password-store=basic before the %U
  • Use the x Close button to save the change

This will of course, use basic password storage, meaning any saved passwords are not encrypted. Perfectly fine if you never use password storage.

Changing the boot splash picture

The default boot splash picture can be replaced using the following instructions:

  • Install ImageMagick which will do the conversion
$ sudo apt-get install imagemagick
  • Create a 1920 x 1080 picture. For the best results, use a PNG image (It supports lossless compression).
  • From the directory in which your new image is stored run the following commands
  • Convert your image to the bootsplash raw format using imagemagick convert.
$ convert yoursplashimage.png -separate +channel -swap 0,2 -combine -colorspace sRGB RGBO:splash.fb
  • Create a backup copy of your current splash screen
$ sudo cp /usr/share/backgrounds/splash.fb /usr/share/backgrounds/splash_original.fb
  • Copy your new splash screen into place
$ sudo cp splash.fb /usr/share/backgrounds/splash.fb
  • Set the correct permissions on the splash.fb file
$ sudo chmod 644 /usr/share/backgrounds/splash.fb
  • If you do not want to see kernel console text messages, make sure you don't have Plymouth installed

Watching Amazon Prime videos with Chromium

When you create a new user, it will be necessary to launch the Chromium browswer with a specific user agent like below;

chromium-browser --user-agent="Mozilla/5.0 (X11; CrOS armv7l 6946.63.0) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/72.0.3626.121 Safari/537.36"

There may be more tweaks needed.

Enabling text boot time messages

By default, most Linux distros have a boot screen with a picture. To see all the boot time messages, use one of the following;

Debian

  • Backup and edit the U-Boot configuration file:
cp -p /etc/default/u-boot /etc/default/u-boot.`date +%Y%m%d`
chmod a-w /etc/default/u-boot.`date +%Y%m%d`
vi /etc/default/u-boot

Remove the quiet and splash parameters. Leave everything else alone.

  • Update the U-Boot configuration:
u-boot-update
  • Test and verify you get what you think you should be seeing.

Manjaro

  • Backup and edit the U-Boot configuration file:
cp -p /boot/extlinux/extlinux.conf /boot/extlinux/extlinux.conf.`date +%Y%m%d`
chmod a-w /boot/extlinux/extlinux.conf.`date +%Y%m%d`
vi /boot/extlinux/extlinux.conf
  • Change console=ttyS2,1500000 to console=tty1
  • Remove the bootsplash.bootfile option and it's parameter.
  • You can add verbose logging by appending ignore_loglevel to the line where boot splash was.
  • Leave everything else alone.
  • Test and verify you get what you think you should be seeing.

Improving readability

Some people find that a 14" LCD screen with 1080p, (1920 x 1080), has text and icons a bit too small. There are things you can do to make the screen easier to use and read.

  • Increase the font size
  • Use a font with more pronounced features
  • Increase the various window manager sizes (e.g. increase the height of the tool bar)
  • Change the color scheme to be easier on the eyes. Higher contrast can help usability.
  • Change the window manager's decorations (e.g. use larger icons)
  • Use a workspace manager, with one application per workspace
  • When at home or office, use an external monitor
  • Change the X-Windows DPI. One such method that someone used successfully, is:

    echo "Xft.dpi: 150" >> ~/.Xresources

    Change the 150 as desired to get the size adjustment you want.


However, do not change the resolution of the LCD screen, otherwise you may end up with a blank / black screen. If that happens, see this troubleshooting section for the fix:
Blank screen after changing builtin LCD resolution

Chromium tweaks

Flags

From the official Debian image:

--disable-low-res-tiling \
--num-raster-threads=6 \
--profiler-timing=0 \
--disable-composited-antialiasing \
--test-type \
--show-component-extension-options \
--ignore-gpu-blacklist \
--use-gl=egl \
--ppapi-flash-path=/usr/lib/chromium-browser/pepper/libpepflashplayer.so \
--ppapi-flash-version=32.0.0.255 \
--enable-pinch \
--flag-switches-begin \
--enable-gpu-rasterization \
--enable-oop-rasterization \
--flag-switches-end

Note that in some cases, this may also decrease performance substantially, as observed when using these flags on the Manjaro KDE desktop. Feel free to experiment to find what is smoothest for you personally.

gVim has performance issue

It appears that using GTK3 can cause very slow scrolling, while Vim in a terminal window works fine.
Simply revert back to using GTK2, (how to do so is somewhat Linux distro-specific).

Another solution may be to run gVim with

GDK_RENDERING=image

environment variable set. It seems that this improves the performance by reverting back to software-only rendering.

Kernel options

Here are some Pinebook Pro & its RK3399 SoC Linux specific options. If kernel version, (or version range specific), it should list that information in the description.

To see if a specific feature is enabled in the current kernel, you can use something like this;

$ zgrep -i rockchip_pcie /proc/config.gz
# CONFIG_ROCKCHIP_PCIE_DMA_OBJ is not set
CONFIG_PHY_ROCKCHIP_PCIE=m

If it's listed as =m, then it's a module. You can see if the module is loaded with;

$ lsmod | grep -i rockchip_pcie
phy_rockchip_pcie      16384  0

Note modules are not loaded until needed. Thus, we sometimes check the kernel configuration instead to see if a feature is configured first, then see if it's a module.

Hardware video decoding

Here is a method to check for hardware video decoding by the VPU. There are special Linux kernel modules that perform this function.
Older systems, such as the previously-default Debian desktop, use the Rockchip-supplied kernel module rk-vcodec. To check, something like this can be used:

$ lsmod | grep rk-vcodec
    or
$ zgrep RK_VCODEC /proc/config.gz
CONFIG_RK_VCODEC=y

Note that in the above example, the Rockchip video CODEC is not built as a module, but included into the kernel. Thus, it does not show up in the list modules check.

Newer systems may use a different option as in the configuration below:

$ zgrep HANTRO /proc/config.gz
CONFIG_VIDEO_HANTRO=m
CONFIG_VIDEO_HANTRO_ROCKCHIP=y

Troubleshooting guide

Do not to panic if something goes wrong or in an unexpected way. Instead, stop and consider carefully how to undo something, or how to redo it. This particularly applies when flashing a new operating system, or flashing new firmware to the keyboard or touchpad. If everything fails, consider reporting the issue on the forums, with as many relevant details as available.

Please, have a look at the Pinebook Pro Troubleshooting Guide, which details a number of issues you may encounter.

Hardware/Accessory Compatibility

Please contribute to the hardware/accessory compatibility page, which lists the status of hardware tested with the Pinebook Pro. Available hardware categories include the following:

Technical Reference

Disassembly and Reassembly

Pinebook Screw stand-offs correct placement and location

There are a few mandatory precautions to be taken:

  • Do not open the laptop by lifting the lid while the Pinebook Pro bottom cover is removed - this can cause structural damage to the hinges and/or other plastic components of the chassis such as the IO port cut-outs.
  • When removing the back cover plate, *do not, under any circumstances, slide your fingertips between the metal shell and the plastic frame!* The back cover plate edges are sharp, and when combined with the pressure and movement generated from, specifically, attempting to slide the tips of your fingers along the bottom edge of the plate along the lid-hinge, they *will* slice open the tips of your fingers like a knife.
  • When removing the back cover plate, use care to avoid damaging the speakers. They can be stuck to the back cover with double-sided tape, and the thin wires are very delicate. Newer Pinebook Pro laptops (as of the May 2021 batch, and perhaps earlier) seem to lack the double-sided tape to the rear cover, instead opting for tape or glue that makes them stick to the front cover. Nevertheless, be gentle when removing the back cover.
Pinebook Pro external screws (this particular unit has suffered damage on screw (4)L)

When disassembling the laptop make sure that it is powered off and folded closed. To remove the bottom cover of the Pinebook Pro, first remove the ten (10) Phillips head screws that hold the bottom section of the laptop in place. There are four (4) short screws along the front edge, and six (6) long screws along the 3 remaining sides. Remove the cover from the back where the hinges are situated by lifting it up and away from the rest of the chassis. The aluminum case is held on only by screws. There are no plastic snaps, and the shell should pull away without any effort. If you experience any resistance at all stop and ensure all ten (10) screws are accounted for.

During reassembly, make sure that the back-screw standoffs are in place and seated correctly. Before replacing the aluminum back-plate, ensure that the speakers are properly seated by pressing gently on the hard plastic edge of the speaker module. Slide the bottom section into place so it meets the front lip of the keyboard section. Secure the front section (where the touchpad is located) in place using the short screws in the front left and right corners. Then proceed to pop in the bottom panel into place. Secure the bottom section (where hinges are located) by screwing in the left and right corners. Then screw in the remaining screws and run your finger though the rim on the chassis to make sure its fitted correctly. Note that the front uses the remaining 4 short screws.

The screws are small and should only be finger tight. Too much force will strip the threads. If after installing screws the back cover plate has not seated properly on one side (which may be caused by the aforementioned misseating of the speakers), open the display and hold the base on either side of the keyboard and gently flex the base with both hands in opposing directions. Once the side pops further in, then recheck the screws on that side. If it does not pop back in, re-open the machine and check for misseated components.

A basic 3D model to print replacement standoffs for the back cover screws is available on Thingiverse, until the official drawings or 3D models are made available.

Internal Layout

Main chips

  • RK3399 system-on-chip (1)
  • LPDDR4 SDRAM (21)
  • SPI NOR flash memory (29)
  • eMMC flash memory (26)
  • WiFi/BT module (27)

Mainboard Switches and Buttons

There are two switches on the main board: disabling the eMMC (24), and enabling UART (9) via headphone jack.

The Reset and Recovery buttons (28): the reset button performs an immediate reset of the laptop. The Recovery button is used to place the device in maskrom mode; this mode allows flashing eMMC using Rockchip tools (e.g. rkflashtools).

PBPL S.jpg

Key Internal Parts

Numbered parts classification and description
Number Type Descriptor
1 Component RK3399 System-On-Chip
2 Socket PCIe x4 slot for optional NVMe adapter
3 Socket Speakers socket
4 Socket Touchpad socket
5 Component Left speaker
6 Connector Power bridge connector
7 Socket Keyboard Socket
8 Component Optional NVMe SSD adapter
9 Switch UART/Audio switch - outputs UART via headphone jack
10 Socket Power bridge socket
11 Socket Battery socket
12 Component Touchpad
13 Component Battery
14 Component Right speaker
15 Socket MicroSD card slot
16 Socket Headphone / UART jack
17 Socket USB 2.0 Type A
18 Socket Daughterboard-to-mainboard ribbon cable socket
19 Cable Daughterboard-to-mainboard ribbon cable
20 Component microphone
21 Component LPDDR4 RAM
22 Socket Mainboard-to-daughterboard ribbon cable socket
23 Socket Microphone socket
24 Switch Switch to hardware disable eMMC
25 Antenna BT/WiFI antenna
26 Component eMMC flash memory module
27 Component BT/WiFi module chip
28 Buttons Reset and recovery buttons
29 Component SPI flash storage
30 Socket eDP LCD socket
31 Socket Power in barrel socket
32 Socket USB 3.0 Type A
33 Socket USB 3.0 Type C

Smallboard detailed picture

Pinebook pro smallboard.jpg

Bootable Storage

Boot sequence details

The RK3399's mask 32KB ROM boot code looks for the next stage of code at byte off-set 32768, (sector 64 if using 512 byte sectors). This is where U-Boot code would reside on any media that is bootable.
RK3399 boot sequence

Boot devices

The Pinebook Pro is capable of booting from eMMC, USB 2.0, USB 3.0, or an SD card. It cannot boot from USB-C. The boot order of the hard-coded ROM of its RK3399 SoC is: SPI NOR, eMMC, SD, USB OTG.

At this time, the Pinebook Pro ships with a Manjaro + KDE build with u-boot on the eMMC. Its boot order is: SD, USB, then eMMC.

(An update has been pushed for the older Debian + MATE build that improves compatibility with booting other OSes from an SD card. In order to update, fully charge the battery, establish an internet connection, click the update icon in the toolbar, and then reboot your Pinebook Pro. Please see this log for details.)

Please note that PCIe, the interface used for NVMe SSD on the Pinebook Pro, is not bootable on the RK3399 and therefore is not a part of the boot hierarchy. It is possible to run the desired OS from NVMe by pointing extlinux on the eMMC to rootfs on the SSD. This requires uboot, the Kernel image, DTB, and extlinux.conf in a /boot partition on the eMMC.

eMMC information

The eMMC appears to be hot-pluggable. This can be useful if trying to recover data or a broken install. Best practice is probably to turn the eMMC switch to off position before changing modules.

The eMMC storage will show up as multiple block devices:

  • mmcblk1boot0 - eMMC standard boot0 partition, may be 4MB
  • mmcblk1boot1 - eMMC standard boot1 partition, may be 4MB
  • mmcblk1rpmb - eMMC standard secure data partition, may be 16MB
  • mmcblk1 - This block contains the user areas

Only the last is usable as regular storage device in the Pinebook Pro. The device number of "1" shown above may vary, depending on kernel.

If the eMMC module is enabled after boot from an SD card, you can detect this change with the following commands as user "root";

echo fe330000.sdhci >/sys/bus/platform/drivers/sdhci-arasan/unbind
echo fe330000.sdhci >/sys/bus/platform/drivers/sdhci-arasan/bind

Case Dimensions and Data

  • Dimensions: 329mm x 220mm x 12mm (WxDxH)
  • Weight: 1.26Kg
  • Screws
    • Philips head type screws
    • M2 flat head machine screws (measurements in mm)
    • 4 x Small screws (used along the front edge): Head - 3.44, Thread Diameter - 1.97, Thread Length - 2.1, Overall length - 3.05
    • 6 x Large screws: Head - 3.44, Thread Diameter - 1.97, Thread Length - 4.41, Overall Length - 5.85
  • Rubber Feet
    • 18mm diameter
    • 3mm height
    • Dome shaped

SoC and Memory Specification

Rockchip RK3399.png
  • Based on Rockchip RK3399

CPU Architecture

  • big.LITTLE architecture: Dual Cortex-A72 + Quad Cortex-A53, 64-bit CPU
    • Full implementation of the ARM architecture v8-A instruction set (both AArch64 and AArch32)
    • ARM Neon Advanced SIMD (single instruction, multiple data) support for accelerated media and signal processing computation
    • ARMv8 Cryptography Extensions
    • VFPv4 floating point unit supporting single and double-precision operations
    • Hardware virtualization support
    • TrustZone technology support
    • Full CoreSight debug solution
    • One isolated voltage domain to support DVFS
  • Cortex-A72 (big cluster):
  • Cortex-A53 (little cluster):
    • Quad-core Cortex-A53 up to 1.5GHz CPU
    • In-order pipeline with symmetric dual-issue of most instructions
    • L1 cache 32KB Icache and 32KB Dcache for each A53
    • L2 cache 512KB for little cluster
  • Cortex-M0 (control processors):
    • Cortex-M0 CPU
    • Two Cortex-M0 cooperate with the central processors
    • Architecture: Armv6-M
    • Thumb/Thumb2 instruction set
    • 32 bit only

GPU Architecture

  • ARM Mali-T860MP4 Quad-core GPU
  • The highest performance GPUs built on Arm Mali’s famous Midgard architecture, the Mali-T860 GPU is designed for complex graphics use cases and provide stunning visuals for UHD content.
  • Frequency 650MHz
  • Throughput 1300Mtri/s, 10.4Gpix/s
  • Graphic interface standards:
    • OpenGL® ES 1.1, 1.2, 2.0, 3.0, 3.1, 3.2. (Panfrost has initial support of 3.0 beginning 2020/02/27)
    • Vulkan 1.0, using the Mali binary blob. (Panfrost does not support Vulkan as of 2020/06/24)
    • OpenCL™ 1.1, 1.2
    • DirectX® 11 FL11_1
    • RenderScript™

System Memory

  • RAM Memory:
    • LPDDR4
    • 800MHz, (limited by RK3399)
    • Dual memory channels on the CPU, each 32 bits wide
    • Quad memory channels on the RAM chip, each 16 bits wide, 2 bonded together for each CPU channel
    • 4GB as a single 366 pin mobile RAM chip
  • Storage Memory:
    • 64GB eMMC module, can be upgraded to an 128GB eMMC module. (The initial PINE64 community build version shipped with a 128GB eMMC.)
    • eMMC version 5.1, HS400, 8 bit on RK3399 side
    • Bootable
  • SPI flash:
    • Pinebook Pro SPI
    • 128Mbit / 16MByte
    • 1 bit interface
    • Bootable, (first boot device, ahead of eMMC & SD card)
    • U-Boot images can be made to work, but as of 2020/06/24 there is no standardized image available.

Video out

  • USB-C Alt mode DP
  • Up to 3840x2160 p60, dependant on adapter, (2 lanes verses 4 lanes)

Expansion Ports

  • MicroSD card:
    • Bootable
    • Supports SD, SDHC and SDXC cards, up to 512GB tested. SDXC standard says 2TB is the maximum.
    • Version SD3.0, (MMC 4.5), up to 50MB/s
    • SD card Application Performance Class 1 (A1), (or better), recommended by some users, for better IOPS
  • USB ports:
    • 1 x USB 2.0 Type-A Host Port, bootable
    • 1 x USB 3.0 Type-A Host Port, 5Gbps, is not bootable
    • 1 x USB 3.0 Type-C OTG Port, 5Gbps, (includes laptop charging function), is not bootable
    • Note that high power USB devices may not work reliably on a PBP. Or they may draw enough power to drain the battery even when the PBP is plugged into A.C. One alternative is externally powered USB devices.
  • Headphone jack switchable to UART console mux circuit

Additional hardware

Hardware that is not part of the SoC.

Battery

  • Lithium Polymer Battery (10,000 mAH)

Display

  • 14.0" 1920x1080 IPS LCD panel

Lid closed magnet

There is a magnet to detect when the laptop lid is closed, so action can be taken like sleep. This meets up with the Hall sensor on the daughter / small board to detect lid closed.

  • The magnet is located on the LCD panel right side, around 1.5 inches up measure from bottom edge.

Webcam

  • Internal USB attached Webcam

Audio

  • 3.5mm stereo earphone/microphone plug
  • Built-in microphone
  • Built-in stereo speakers:
    • Oval in design
    • 3 mm high x 20 mm x 30 mm

Network

  • WiFi:
    • 802.11 b/g/n/ac
    • Dual band: 2.4Ghz & 5Ghz
    • Single antenna
  • Bluetooth 5.0

Optional NVMe adapter

  • PCIe 2.0, 5 GT/s per lane
  • Four PCIe lanes, which can not be bifurcated, but can be used with one- or two-lane NVMe cards
  • M keyed, though M+B keyed devices will work too
  • Maximum length for M.2 card is 80mm (M.2 2280). The following sizes will also work: 2230, 2242, 2260
  • Power: 2.5 W continuous, 8.25 W peak momentary
  • Does not support SATA M.2 cards
  • Does not support USB M.2 cards

Pinebook Pro Schematics and Certifications

Datasheets for Components and Peripherals

Versions

Pinebook Pro v1 and v2 were prototype models that did not make it to the public. The "first batch" (First 100 forum preorders) onward are v2.1. [2]

Skinning and Case Customization

Other Resources