Difference between revisions of "PinePhone Thermal Tweaks"

From PINE64
Jump to navigation Jump to search
(→‎Under Linux: Better and more accurate wording)
(added to pinephone category)
 
(8 intermediate revisions by 2 users not shown)
Line 5: Line 5:
{{warning|Setting wrong values for the thermal trip points poses a risk. These instructions are directed towards expert-level users and developers.}}
{{warning|Setting wrong values for the thermal trip points poses a risk. These instructions are directed towards expert-level users and developers.}}


Thermal management of the PinePhone SoC is handled by the thermal framework of the Linux kernel. Depending on the Linux distribution used on a PinePhone, the default settings may differ. It may be advised to lower the settings (i.e. the thermal trip point tmperatures) to prevent the phone components from being damaged by excessive heat.
Thermal management of the PinePhone CPU is handled by the thermal framework of the Linux kernel. Depending on the Linux distribution used on a PinePhone, the default settings may differ. It may be advised to lower the settings (i.e. the thermal trip point temperatures) to prevent the phone components from being damaged by excessive heat.


Current CPU temperature can be displayed using the following command:
Current CPU temperature can be displayed using the following command:
Line 16: Line 16:
  grep . /sys/class/thermal/thermal_zone0/trip_point_*_type
  grep . /sys/class/thermal/thermal_zone0/trip_point_*_type


The possible names and associated meanings for the trip point types are the following:
The default trip point temperatures are also available in the [https://elixir.bootlin.com/linux/v5.12/source/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi#L194 A64 device tree]. The possible names and associated meanings for the trip point types are the following:


* "active" – a trip point to enable active cooling
* "active" – a trip point to enable active cooling
Line 23: Line 23:
* "critical" – hardware not reliable
* "critical" – hardware not reliable


The values for the trip point temperatures can be lowered individually, but make sure the trip points have the correct number for their corresponding trip type, e.g. '''don't''' swap the values for the first and the second trip point. '''Make sure not to set values higher than 110000''' (i.e. 110 degrees Celsius, which is the default value) for the third threshold, as it may cause damage to the phone. Use the following commands:
The values for the trip point temperatures can be lowered individually, but make sure the trip points have the correct value for their corresponding trip type, e.g. '''don't''' simply swap the values for the first and the second trip point. '''Make sure not to set values higher than 110000''' (i.e. 110 degrees Celsius, which is the default value) for the third threshold, as it may cause damage to the phone. Use the following commands:


  echo 55000 > /sys/class/thermal/thermal_zone0/trip_point_0_temp
  echo 55000 > /sys/class/thermal/thermal_zone0/trip_point_0_temp # passive
  echo 75000 > /sys/class/thermal/thermal_zone0/trip_point_1_temp
  echo 75000 > /sys/class/thermal/thermal_zone0/trip_point_1_temp # hot
  echo 90000 > /sys/class/thermal/thermal_zone0/trip_point_2_temp
  echo 100000 > /sys/class/thermal/thermal_zone0/trip_point_2_temp # critical


Further information can be found in these documents from the Linux kenel source:
Further information can be found in these documents from the Linux kenel source:
Line 34: Line 34:
* [https://www.kernel.org/doc/Documentation/hwmon/sysfs-interface Documentation/hwmon/sysfs-interface]
* [https://www.kernel.org/doc/Documentation/hwmon/sysfs-interface Documentation/hwmon/sysfs-interface]
* [https://www.kernel.org/doc/Documentation/devicetree/bindings/thermal/thermal.txt Documentation/devicetree/bindings/thermal/thermal.txt]
* [https://www.kernel.org/doc/Documentation/devicetree/bindings/thermal/thermal.txt Documentation/devicetree/bindings/thermal/thermal.txt]
[[Category:PinePhone]]

Latest revision as of 01:50, 16 August 2022

This page explains how to read the thermal sensor data, and how to read and change the default settings.

Under Linux

Warning: Setting wrong values for the thermal trip points poses a risk. These instructions are directed towards expert-level users and developers.

Thermal management of the PinePhone CPU is handled by the thermal framework of the Linux kernel. Depending on the Linux distribution used on a PinePhone, the default settings may differ. It may be advised to lower the settings (i.e. the thermal trip point temperatures) to prevent the phone components from being damaged by excessive heat.

Current CPU temperature can be displayed using the following command:

cat /sys/class/thermal/thermal_zone0/temp

The unit for all numeric values is millidegree Celsius. To read the thermal trip point types and current trip point temperatures, use the following:

grep . /sys/class/thermal/thermal_zone0/trip_point_*_temp
grep . /sys/class/thermal/thermal_zone0/trip_point_*_type

The default trip point temperatures are also available in the A64 device tree. The possible names and associated meanings for the trip point types are the following:

  • "active" – a trip point to enable active cooling
  • "passive" – a trip point to enable passive cooling
  • "hot" – a trip point to notify emergency
  • "critical" – hardware not reliable

The values for the trip point temperatures can be lowered individually, but make sure the trip points have the correct value for their corresponding trip type, e.g. don't simply swap the values for the first and the second trip point. Make sure not to set values higher than 110000 (i.e. 110 degrees Celsius, which is the default value) for the third threshold, as it may cause damage to the phone. Use the following commands:

echo 55000  > /sys/class/thermal/thermal_zone0/trip_point_0_temp  # passive
echo 75000  > /sys/class/thermal/thermal_zone0/trip_point_1_temp  # hot
echo 100000 > /sys/class/thermal/thermal_zone0/trip_point_2_temp  # critical

Further information can be found in these documents from the Linux kenel source: