Difference between revisions of "PineCube"

From PINE64
Jump to navigation Jump to search
(→‎Buildroot: mention upstream support)
 
(174 intermediate revisions by 20 users not shown)
Line 1: Line 1:
PAGE UNDER CONSTRUCTION, INFO SUBJECT TO CHANGE
[[File:PineCube.jpg|400px|thumb|right|The PineCube]]


The '''PineCube''' is a small, low-powered, open source IP camera. Whether you’re a parent looking for a FOSS baby-camera, a privacy oriented shop keeper, home owner looking for a security camera, or perhaps a tinkerer needing a camera for your drone – the CUBE can be the device for you. It features an 5MPx Omnivision sensor and IR LEDs for night vision, as well as Power Over Ethernet, as well as a microphone.


== Specifications ==


== Specifications ==
* '''Dimensions:''' 55mm x 51mm x 51.5mm
* '''Dimensions:''' 55mm x 51mm x 51.5mm
* '''Weight:''' 55g
* '''Weight:''' 55g
Line 12: Line 13:
* '''CPU:''' Allwinner(Sochip) ARM Cortex-A7 MPCore, 800MHz
* '''CPU:''' Allwinner(Sochip) ARM Cortex-A7 MPCore, 800MHz
* '''RAM:''' 128MB DDR3
* '''RAM:''' 128MB DDR3
* '''I/O:''' 10/100Mbps Ethernet with passive PoE, USB 2.0 A host, 26 pins GPIO port, internal mic
* '''I/O:'''
* '''Network'''
** 10/100Mbps Ethernet with passive PoE (''4-18V!'')
** USB 2.0 A host
** 26 pins GPIO port
*** 2x 3.3V Ouptut
*** 2x 5V Output
*** 1x I2C
*** 2x UART (3.3V)
*** 2x PWM
*** 1x SPI
*** 1x eMMC/SDIO/SD (8-bit)
*** 6x Interrupts
*** '''Note: Interfaces are multiplexed, so they can't be all used at same time'''
** Internal microphone
* '''Network:'''
** WiFi
** WiFi
* '''Screen:''' optional 4.5" RGB LCD screen
* '''Screen:''' optional 4.5" RGB LCD screen ( RB043H40T03A-IPS or DFC-XS4300240 V01 )
* '''Battery:''' optional 1200MAh (1.2Ah)
* '''Misc. features:'''  
* '''Misc. features:'''  
** Volume and home buttons
** Volume and home buttons
** Speakers and Microphone
** Speakers and Microphone
** DC in: 5V 1A from microUSB Port and GPIO port, 8V-24V from Ethernet passive PoE.
** IR LEDs for night vision
** Passive infrared sensor
* '''Power DC in:'''
** 5V 1A from MicroUSB Port or GPIO port
** 4V-18V from Ethernet passive PoE
* '''Battery:''' optional 950-1600mAh model: 903048 Lithium Polymer Ion Battery Pack, can be purchase at [https://www.amazon.com/AKZYTUE-1200mAh-Battery-Rechargeable-Connector/dp/B07TWHHCNK/ Amazon.com]
 
== GPIO pinout ==
 
[[File:PineCube_GPIO_Pinout.png|700px]]


Note: Pin1 is marked on the board by a white dot on the PCB. See the [[:File:PineCube_GPIO.pdf|PDF]] and [https://pine64.gami.ee/pinecube/gpio-pinout.html HTML] for details.


== PineCube board information, schematics and certifications ==
== Projects ==
* PineCube mainboard schematic:
** [http://files.pine64.org/doc/PineCube/PineCube%20MainBoard%20Schematic%20ver%201.0-20200727.pdf PineCube mainboard Released Schematic ver 1.0]
* PineCube faceboard schematic:
** [http://files.pine64.org/doc/PineCube/PineCube%20FaceBoard%20Schematic%20ver%201.0-20200727.pdf PineCube faceboard Released Schematic ver 1.0]
* PineCube certifications:


The following projects are documented here:


* [[PineCube: Streaming the camera to the network]]
* [[PineCube as a security camera with Motion]]
* [[PineCube as a WiFi AP]]
* [[PineCube as a webcam]]
* [[PineCube as a recorder for loud noises]]


== Datasheets for components and peripherals ==
Further projects:
* Allwinner (Sochip) S3 SoC information:
** [http://files.pine64.org/doc/datasheet/pinecube/S3_Datasheet_V1.1-20180123.pdf Sochip S3 SoC Data Sheet V1.1]


* X-Powers AXP209 PMU (Power Management Unit) information:
* ''OpenWrt'' from ''juansef'' - [https://github.com/juanesf/openwrt GitHub], [https://forum.pine64.org/showthread.php?tid=13158&pid=98379 Pine64 Forum thread]
** [http://files.pine64.org/doc/datasheet/pinecube/AXP209_Datasheet_v1.0en.pdf AXP209 PMIC datasheet]


* CMOS camera module information:
== Case information ==
** [http://files.pine64.org/doc/datasheet/pinephone/OV5640_datasheet.pdf OV5640 5MP CMOS Image Sensor SoC datasheet]


* LCD touch screen panel information:
<gallery>
File:PineCube_Case-1.jpg
File:PineCube_Case-2.jpg
</gallery>


* Lithium battery information:
Model:


* WiFi/BT module information:
* [https://files.pine64.org/doc/PineCube/PineCube%20Case%203D.zip PineCube (proprietary) 3D file]
** [http://files.pine64.org/doc/datasheet/pinecube/rtl8189es.pdf RTL8189ES specification]


User models:


* [https://drive.google.com/file/d/1MDNxnPL2kuYGC4Y4qf9J6YPYZF15KnN7/view?usp=sharing Quick and dirty STL conversion (beta) by doodlebro. Prints and fits at 0.25mm layer height.]
* [https://drive.google.com/drive/folders/1ddisX1V2qibqFuQG74-7w9SgdOE1idTN?usp=sharing New model with removable front cover and mounting plate with hole for strong magnet and adjustable rotation angle.] See README for more details. Available FreeCAD source models, STL, G-code and 3mf data. [https://www.printables.com/cs/model/296091-pinecube-box Also available at printables.com]


== Operating Systems ==
== Operating Systems ==


=== Stock Linux ===
=== Armbian ===
[[File:armbian.png|right|100px]]
 
'''Armbian''' is a Linux distribution designed for ARM boards. They are usually Debian or Ubuntu flavored.
 
Download:
 
* https://www.armbian.com/pinecube/
 
Notes:
 
* See [[PineCube Armbian Notes]]
 
=== NixOS ===
[[File:NixOS.webp|right|100px]]
 
'''NixOS''' is a Linux distribution built on top of the Nix package manager using declarative configuration to allow reliable system upgrades.
 
* [https://github.com/danielfullmer/pinecube-nixos danielfullmer's Github]
 
=== Buildroot ===
 
PineCube is supported in Buildroot since version 2023.11. See the file [https://git.busybox.net/buildroot/tree/board/pine64/pinecube/readme.txt?h=next board/pine64/pinecube/readme.txt] in the Buildroot repository for details how to build it.
 
There is also available Buildroot fork by [https://elimo.io Elimo Engineering], you can find the repository on [https://github.com/elimo-engineering/buildroot Elimo's GitHub account] and build instructions in the [https://github.com/elimo-engineering/buildroot/tree/pine64/pinecube/board/pine64/pinecube board support directory] readme.
 
The most important thing that this provides is support for the S3's DDR3 in u-boot. Unfortunately mainline u-boot does not have that yet, but the u-boot patches from [https://github.com/danielfullmer/pinecube-nixos Daniel Fullmer's NixOS repo] were easy enough to use on buildroot.
 
This should get you a functional system that boots to a console on UART0. It's pretty fast too, getting there in 1.5 seconds from u-boot to login prompt.
 
=== Mainlining Efforts ===
 
Please note:
 
* this list is most likely not complete
* no review of functionality is done here, it only serves as a collection of efforts
 
{| class="wikitable"
!colspan="3"|Linux kernel
|-
| Type
| Link
| Available in version
|-
| Devicetree Entry Pinecube
| https://lkml.org/lkml/2020/9/22/1241
| 5.10
|-
| Correction for AXP209 driver
| https://lkml.org/lkml/2020/9/22/1243
| 5.9
|-
| Additional Fixes for AXP209 driver
| https://lore.kernel.org/lkml/20201031182137.1879521-8-contact@paulk.fr/
| 5.12
|-
| Device Tree Fixes
| https://lore.kernel.org/lkml/20201003234842.1121077-1-icenowy@aosc.io/
| 5.10
|-
| Audio Device and IR LED Fix
| https://github.com/danielfullmer/pinecube-nixos/blob/master/kernel/Pine64-PineCube-support.patch
| [https://github.com/danielfullmer/pinecube-nixos/issues/2 TBD]
|-
!colspan="3"|U-boot
|-
| Type
| Link
| Available in version
|-
| PineCube Board Support
| https://patchwork.ozlabs.org/project/uboot/list/?series=210044
| v2021.04
|-
!colspan="3"|Buildroot
|-
| Type
| Link
| Available in version
|-
| PineCube Board Support
| https://patchwork.ozlabs.org/project/buildroot/list/?series=314653
| 2023.11
|}
 
== Debugging ==
 
Camera issues can be debugged with the gstreamer pipeline. If the camera does not appear to work, it is possible to change the <code>v4l2src</code> to <code>videotestsrc</code> and the gstreamer pipeline will produce a synthetic test image without using the camera hardware.
 
If the camera is only sensor noise lines over a black or white image, the camera may be in a broken state. When in that state, the following kernel messages were observed:
 
[ 1703.577304] alloc_contig_range: [46100, 464f5) PFNs busy
[ 1703.578570] alloc_contig_range: [46200, 465f5) PFNs busy
[ 1703.596924] alloc_contig_range: [46300, 466f5) PFNs busy
[ 1703.598060] alloc_contig_range: [46400, 467f5) PFNs busy
[ 1703.600480] alloc_contig_range: [46400, 468f5) PFNs busy
[ 1703.601654] alloc_contig_range: [46600, 469f5) PFNs busy
[ 1703.619165] alloc_contig_range: [46100, 464f5) PFNs busy
[ 1703.619528] alloc_contig_range: [46200, 465f5) PFNs busy
[ 1703.619857] alloc_contig_range: [46300, 466f5) PFNs busy
[ 1703.641156] alloc_contig_range: [46100, 464f5) PFNs busy
 
== Camera Adjustments ==
 
=== Focus ===
 
The focus of the lens can be manually adjusted through rotation. Note that initially, the lens could be tight.
 
=== Low light mode ===
 
To get imagery in low-light conditions you can turn on the infrared LED's to light up the dark area and also enable the IR cut filter using the commands below. Note that these were performed on Armbian using the instructions from here [https://github.com/danielfullmer/pinecube-nixos#enablingdisabling-ir-cut-filter].
 
<pre>
# Run these as root
 
# Turn on the IR LED lights (note that you can see a faint red glow from them when it's low light)
# Turn them off with echo 1 instead (this may be inverted depending on the version of the kernel you have)
# echo 0 > /sys/class/leds/pine64\:ir\:led1/brightness
# echo 0 > /sys/class/leds/pine64\:ir\:led2/brightness
 
# Export gpio, set direction
# echo 45 > /sys/class/gpio/export
# echo out > /sys/class/gpio/gpio45/direction
 
# Enable IR cut filter (note that you can hear the switching noise)
# Disable with echo 0 instead
# echo 1 > /sys/class/gpio/gpio45/value
</pre>
 
=== Camera controls ===
 
It is possible to adjust the camera using certain internal camera controls, such as contrast, brightness, saturation and more. These controls can be accessed using the v4l2-ctl tool that is part of the v4l-utils package.
 
<pre>
# List the current values of the controls
v4l2-ctl -d /dev/v4l-subdev* --list-ctrls
 
User Controls
 
                      contrast 0x00980901 (int)    : min=0 max=255 step=1 default=0 value=0 flags=slider
                    saturation 0x00980902 (int)    : min=0 max=255 step=1 default=64 value=64 flags=slider
                            hue 0x00980903 (int)    : min=0 max=359 step=1 default=0 value=0 flags=slider
        white_balance_automatic 0x0098090c (bool)  : default=1 value=1 flags=update
                    red_balance 0x0098090e (int)    : min=0 max=4095 step=1 default=0 value=0 flags=inactive, slider
                  blue_balance 0x0098090f (int)    : min=0 max=4095 step=1 default=0 value=0 flags=inactive, slider
                      exposure 0x00980911 (int)    : min=0 max=65535 step=1 default=0 value=4 flags=inactive, volatile
                gain_automatic 0x00980912 (bool)  : default=1 value=1 flags=update
                          gain 0x00980913 (int)    : min=0 max=1023 step=1 default=0 value=20 flags=inactive, volatile
                horizontal_flip 0x00980914 (bool)  : default=0 value=0
                  vertical_flip 0x00980915 (bool)  : default=0 value=0
          power_line_frequency 0x00980918 (menu)  : min=0 max=3 default=1 value=1
 
Camera Controls
 
                  auto_exposure 0x009a0901 (menu)  : min=0 max=1 default=0 value=0 flags=update
 
Image Processing Controls
 
                    pixel_rate 0x009f0902 (int64)  : min=0 max=2147483647 step=1 default=61430400 value=21001200 flags=read-only
                  test_pattern 0x009f0903 (menu)  : min=0 max=4 default=0 value=0
 
# Set the contrast controls to the maximum value
v4l2-ctl -d /dev/v4l-subdev* --set-ctrl contrast=255
</pre>


You can see which flags can be changed and which ones cannot by looking at the flags. The inactive flag indicates that it is currently disabled. Some of these flags are disabled when other flags are turned on. For example, the gain flag above is inactive because gain_automatic is enabled with a value of "1." Note that at the current time '''the auto_exposure flag is inverted, so a value of "0" means on, while "1" means off.''' Maybe the auto_exposure flag will get changed someday. You'll need to turn off auto_exposure (value=1) if you want to manually set the exposure flag.


== Sound Controls ==


Note that sound is only currently available with special patches on top of a 5.13.13 or higher kernel with Armbian or NixOS. Once you have a kernel that supports sound you can install alsa-utils to get the alsamixer tool. The following mixer settings have been found to work with both playback and record. Note that you'll need to press F5 to get the capture controls and space bar to turn on/off capture for a device. The speaker dangles on a wire from the device. The microphone is located about 1cm below the lens on the front facing circuit board.
[[File:Pinecube_sound_mixer.png|800px]]


== SDK ==
== SDK ==


==== Stock Linux ====
Stock Linux:
* [http://files.pine64.org/SDK/PineCube/PineCube%20Stock%20BSP-SDK%20ver1.0.7z Direct Download from pine64.org]
 
** MD5 (7zip file): efac108dc98efa0a1f5e77660ba375f8
* [https://files.pine64.org/SDK/PineCube/PineCube%20Stock%20BSP-SDK%20ver1.0.7z Direct Download from pine64.org] (MD5 (7zip file): efac108dc98efa0a1f5e77660ba375f8, file size: 3.50GB)
** File Size: 3.50GB
 
Compilation:
 
You can either setup a machine for the build environment, or use a Vagrant virtual machine provided by [https://elimo.io Elimo Engineering]
 
=== Compile on a dedicated machine ===
 
Recommended system requirements:
 
* OS: (L)Ubuntu 16.04
* CPU: 64-bit based
* Memory: 8 GB or higher
* Disk: 15 GB free hard disk space
 
Install required packages:
 
sudo apt-get install p7zip-full git make u-boot-tools libxml2-utils bison build-essential gcc-arm-linux-gnueabi g++-arm-linux-gnueabi zlib1g-dev gcc-multilib g++-multilib libc6-dev-i386 lib32z1-dev
 
Install older Make 3.82 and Java JDK 6:
 
pushd /tmp
wget https://ftp.gnu.org/gnu/make/make-3.82.tar.gz
tar xfv make-3.82.tar.gz
cd make-3.82
./configure
make
sudo apt purge -y make
sudo ./make install
cd ..
# Please, download jdk-6u45-linux-x64.bin from https://www.oracle.com/java/technologies/javase-java-archive-javase6-downloads.html (requires free login)
chmod +x jdk-6u45-linux-x64.bin
./jdk-6u45-linux-x64.bin
sudo mkdir /opt/java/
sudo mv jdk1.6.0_45/ /opt/java/
sudo update-alternatives --install /usr/bin/javac javac /opt/java/jdk1.6.0_45/bin/javac 1
sudo update-alternatives --install /usr/bin/java java /opt/java/jdk1.6.0_45/bin/java 1
sudo update-alternatives --install /usr/bin/javaws javaws /opt/java/jdk1.6.0_45/bin/javaws 1
sudo update-alternatives --config javac
sudo update-alternatives --config java
sudo update-alternatives --config javaws
popd
 
PineCubes SPI Flash support patch:
 
From 9316112c37ee86645fd691c6d3352183b95177d8 Mon Sep 17 00:00:00 2001
From: Marek Kraus <gamelaster@outlook.com>
Date: Fri, 8 Jul 2022 21:01:47 +0200
Subject: [PATCH] Add support for xt25f128 SPI Flash
---
drivers/mtd/devices/m25p80.c | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/mtd/devices/m25p80.c b/drivers/mtd/devices/m25p80.c
index 31e5795..0f46a4c 100755
--- a/drivers/mtd/devices/m25p80.c
+++ b/drivers/mtd/devices/m25p80.c
@@ -803,6 +803,7 @@ static const struct spi_device_id m25p_ids[] = {
  { "w25x64", INFO(0xef3017, 0, 64 * 1024, 128, SECT_4K) },
  { "w25q64", INFO(0xef4017, 0, 64 * 1024, 128, SECT_4K) },
  { "W25q128", INFO(0xef4018, 0, 64 * 1024, 256, 0) },
+ { "xt25f128", INFO(0x0b4018, 0, 64 * 1024, 256, SECT_4K) },
 
 
  /* Catalyst / On Semiconductor -- non-JEDEC */
--
2.7.4
 
Unpack SDK and then compile and pack the image:
 
7z x 'PineCube Stock BSP-SDK ver1.0.7z'
mv 'PineCube Stock BSP-SDK ver1.0' pinecube-sdk
cd pinecube-sdk/camdroid
# apply SPI Flash patch above or edit m25p80.c file
source build/envsetup.sh
lunch # select [1] here
mklichee
extract-bsp
make -j3
pack
 
=== Compile using Vagrant ===
 
You can avoid setting up your machine and just use Vagrant to spin up a development environment in a VM.
 
Just clone the [https://github.com/elimo-engineering/pinecube-sdk-vagrant Elimo Engineering repo] and follow the instructions in the [https://github.com/elimo-engineering/pinecube-sdk-vagrant/blob/main/README.md readme file]
 
After spinning up the VM, you just need to run the build:
 
cd pinecube-sdk/camdroid
# apply SPI Flash patch above or edit m25p80.c file
source build/envsetup.sh
lunch # select [1] here
mklichee
extract-bsp
make -j3
pack
 
=== Flashing the image ===
 
See [[PhoenixCard]] for a manual on how to flash Allwinners BSP images.
 
== Board information, schematics and certifications ==
 
PineCube mainboard schematic:
 
* [https://files.pine64.org/doc/PineCube/PineCube%20MainBoard%20Schematic%20ver%201.0-20200727.pdf PineCube mainboard Released Schematic ver 1.0]
 
PineCube faceboard schematic:
 
* [https://files.pine64.org/doc/PineCube/PineCube%20FaceBoard%20Schematic%20ver%201.0-20200727.pdf PineCube faceboard Released Schematic ver 1.0]
 
PineCube certifications:
 
* [https://files.pine64.org/doc/cert/PineCube-FCC-SDOC%20certification%20S20072502302001.pdf PineCube FCC Certificate]
* [https://files.pine64.org/doc/cert/PineCube-CE-EMC%20certification%20S20072502301001.pdf PineCube CE RED Certificate]
* [https://files.pine64.org/doc/cert/PineCube-ROHS%20Test%20Report.pdf PineCube ROHS Test Report]
 
== Datasheets for components and peripherals ==
 
Allwinner (Sochip) S3 SoC information:
 
* [https://files.pine64.org/doc/datasheet/pinecube/S3_Datasheet_V1.1-20180123.pdf Sochip S3 SoC Data Sheet V1.1]
 
X-Powers AXP209 PMU (Power Management Unit) information:
 
* [https://files.pine64.org/doc/datasheet/pinecube/AXP209_Datasheet_v1.0en.pdf AXP209 PMIC datasheet]
 
CMOS camera module information:
 
* [https://files.pine64.org/doc/datasheet/pinecube/CH-5A-DV-V2.0%20Specification.pdf PineCube Camera Module Specification]
* [https://files.pine64.org/doc/datasheet/pinephone/OV5640_datasheet.pdf OV5640 5MP CMOS Image Sensor SoC datasheet]
 
LCD touch screen panel information:
 
Lithium battery information:
 
WiFi/BT module information:
 
* [https://files.pine64.org/doc/datasheet/pinecube/rtl8189es.pdf RTL8189ES specification]
 
 
[[Category:PineCube]] [[Category:Allwinner(Sochip) S3]]

Latest revision as of 15:48, 3 September 2023

The PineCube

The PineCube is a small, low-powered, open source IP camera. Whether you’re a parent looking for a FOSS baby-camera, a privacy oriented shop keeper, home owner looking for a security camera, or perhaps a tinkerer needing a camera for your drone – the CUBE can be the device for you. It features an 5MPx Omnivision sensor and IR LEDs for night vision, as well as Power Over Ethernet, as well as a microphone.

Specifications

  • Dimensions: 55mm x 51mm x 51.5mm
  • Weight: 55g
  • Storage:
    • MicroSD slot, bootable
    • 128Mb SPI Nor Flash, bootable
  • Cameras: OV5640, 5Mpx
  • CPU: Allwinner(Sochip) ARM Cortex-A7 MPCore, 800MHz
  • RAM: 128MB DDR3
  • I/O:
    • 10/100Mbps Ethernet with passive PoE (4-18V!)
    • USB 2.0 A host
    • 26 pins GPIO port
      • 2x 3.3V Ouptut
      • 2x 5V Output
      • 1x I2C
      • 2x UART (3.3V)
      • 2x PWM
      • 1x SPI
      • 1x eMMC/SDIO/SD (8-bit)
      • 6x Interrupts
      • Note: Interfaces are multiplexed, so they can't be all used at same time
    • Internal microphone
  • Network:
    • WiFi
  • Screen: optional 4.5" RGB LCD screen ( RB043H40T03A-IPS or DFC-XS4300240 V01 )
  • Misc. features:
    • Volume and home buttons
    • Speakers and Microphone
    • IR LEDs for night vision
    • Passive infrared sensor
  • Power DC in:
    • 5V 1A from MicroUSB Port or GPIO port
    • 4V-18V from Ethernet passive PoE
  • Battery: optional 950-1600mAh model: 903048 Lithium Polymer Ion Battery Pack, can be purchase at Amazon.com

GPIO pinout

PineCube GPIO Pinout.png

Note: Pin1 is marked on the board by a white dot on the PCB. See the PDF and HTML for details.

Projects

The following projects are documented here:

Further projects:

Case information

Model:

User models:

Operating Systems

Armbian

Armbian.png

Armbian is a Linux distribution designed for ARM boards. They are usually Debian or Ubuntu flavored.

Download:

Notes:

NixOS

Error creating thumbnail: File missing

NixOS is a Linux distribution built on top of the Nix package manager using declarative configuration to allow reliable system upgrades.

Buildroot

PineCube is supported in Buildroot since version 2023.11. See the file board/pine64/pinecube/readme.txt in the Buildroot repository for details how to build it.

There is also available Buildroot fork by Elimo Engineering, you can find the repository on Elimo's GitHub account and build instructions in the board support directory readme.

The most important thing that this provides is support for the S3's DDR3 in u-boot. Unfortunately mainline u-boot does not have that yet, but the u-boot patches from Daniel Fullmer's NixOS repo were easy enough to use on buildroot.

This should get you a functional system that boots to a console on UART0. It's pretty fast too, getting there in 1.5 seconds from u-boot to login prompt.

Mainlining Efforts

Please note:

  • this list is most likely not complete
  • no review of functionality is done here, it only serves as a collection of efforts
Linux kernel
Type Link Available in version
Devicetree Entry Pinecube https://lkml.org/lkml/2020/9/22/1241 5.10
Correction for AXP209 driver https://lkml.org/lkml/2020/9/22/1243 5.9
Additional Fixes for AXP209 driver https://lore.kernel.org/lkml/20201031182137.1879521-8-contact@paulk.fr/ 5.12
Device Tree Fixes https://lore.kernel.org/lkml/20201003234842.1121077-1-icenowy@aosc.io/ 5.10
Audio Device and IR LED Fix https://github.com/danielfullmer/pinecube-nixos/blob/master/kernel/Pine64-PineCube-support.patch TBD
U-boot
Type Link Available in version
PineCube Board Support https://patchwork.ozlabs.org/project/uboot/list/?series=210044 v2021.04
Buildroot
Type Link Available in version
PineCube Board Support https://patchwork.ozlabs.org/project/buildroot/list/?series=314653 2023.11

Debugging

Camera issues can be debugged with the gstreamer pipeline. If the camera does not appear to work, it is possible to change the v4l2src to videotestsrc and the gstreamer pipeline will produce a synthetic test image without using the camera hardware.

If the camera is only sensor noise lines over a black or white image, the camera may be in a broken state. When in that state, the following kernel messages were observed:

[ 1703.577304] alloc_contig_range: [46100, 464f5) PFNs busy
[ 1703.578570] alloc_contig_range: [46200, 465f5) PFNs busy
[ 1703.596924] alloc_contig_range: [46300, 466f5) PFNs busy
[ 1703.598060] alloc_contig_range: [46400, 467f5) PFNs busy
[ 1703.600480] alloc_contig_range: [46400, 468f5) PFNs busy
[ 1703.601654] alloc_contig_range: [46600, 469f5) PFNs busy
[ 1703.619165] alloc_contig_range: [46100, 464f5) PFNs busy
[ 1703.619528] alloc_contig_range: [46200, 465f5) PFNs busy
[ 1703.619857] alloc_contig_range: [46300, 466f5) PFNs busy
[ 1703.641156] alloc_contig_range: [46100, 464f5) PFNs busy

Camera Adjustments

Focus

The focus of the lens can be manually adjusted through rotation. Note that initially, the lens could be tight.

Low light mode

To get imagery in low-light conditions you can turn on the infrared LED's to light up the dark area and also enable the IR cut filter using the commands below. Note that these were performed on Armbian using the instructions from here [1].

# Run these as root

# Turn on the IR LED lights (note that you can see a faint red glow from them when it's low light)
# Turn them off with echo 1 instead (this may be inverted depending on the version of the kernel you have)
# echo 0 > /sys/class/leds/pine64\:ir\:led1/brightness
# echo 0 > /sys/class/leds/pine64\:ir\:led2/brightness

# Export gpio, set direction
# echo 45 > /sys/class/gpio/export
# echo out > /sys/class/gpio/gpio45/direction

# Enable IR cut filter (note that you can hear the switching noise)
# Disable with echo 0 instead
# echo 1 > /sys/class/gpio/gpio45/value

Camera controls

It is possible to adjust the camera using certain internal camera controls, such as contrast, brightness, saturation and more. These controls can be accessed using the v4l2-ctl tool that is part of the v4l-utils package.

# List the current values of the controls
v4l2-ctl -d /dev/v4l-subdev* --list-ctrls

User Controls

                       contrast 0x00980901 (int)    : min=0 max=255 step=1 default=0 value=0 flags=slider
                     saturation 0x00980902 (int)    : min=0 max=255 step=1 default=64 value=64 flags=slider
                            hue 0x00980903 (int)    : min=0 max=359 step=1 default=0 value=0 flags=slider
        white_balance_automatic 0x0098090c (bool)   : default=1 value=1 flags=update
                    red_balance 0x0098090e (int)    : min=0 max=4095 step=1 default=0 value=0 flags=inactive, slider
                   blue_balance 0x0098090f (int)    : min=0 max=4095 step=1 default=0 value=0 flags=inactive, slider
                       exposure 0x00980911 (int)    : min=0 max=65535 step=1 default=0 value=4 flags=inactive, volatile
                 gain_automatic 0x00980912 (bool)   : default=1 value=1 flags=update
                           gain 0x00980913 (int)    : min=0 max=1023 step=1 default=0 value=20 flags=inactive, volatile
                horizontal_flip 0x00980914 (bool)   : default=0 value=0
                  vertical_flip 0x00980915 (bool)   : default=0 value=0
           power_line_frequency 0x00980918 (menu)   : min=0 max=3 default=1 value=1

Camera Controls

                  auto_exposure 0x009a0901 (menu)   : min=0 max=1 default=0 value=0 flags=update

Image Processing Controls

                     pixel_rate 0x009f0902 (int64)  : min=0 max=2147483647 step=1 default=61430400 value=21001200 flags=read-only
                   test_pattern 0x009f0903 (menu)   : min=0 max=4 default=0 value=0

# Set the contrast controls to the maximum value
v4l2-ctl -d /dev/v4l-subdev* --set-ctrl contrast=255

You can see which flags can be changed and which ones cannot by looking at the flags. The inactive flag indicates that it is currently disabled. Some of these flags are disabled when other flags are turned on. For example, the gain flag above is inactive because gain_automatic is enabled with a value of "1." Note that at the current time the auto_exposure flag is inverted, so a value of "0" means on, while "1" means off. Maybe the auto_exposure flag will get changed someday. You'll need to turn off auto_exposure (value=1) if you want to manually set the exposure flag.

Sound Controls

Note that sound is only currently available with special patches on top of a 5.13.13 or higher kernel with Armbian or NixOS. Once you have a kernel that supports sound you can install alsa-utils to get the alsamixer tool. The following mixer settings have been found to work with both playback and record. Note that you'll need to press F5 to get the capture controls and space bar to turn on/off capture for a device. The speaker dangles on a wire from the device. The microphone is located about 1cm below the lens on the front facing circuit board.

Pinecube sound mixer.png

SDK

Stock Linux:

Compilation:

You can either setup a machine for the build environment, or use a Vagrant virtual machine provided by Elimo Engineering

Compile on a dedicated machine

Recommended system requirements:

  • OS: (L)Ubuntu 16.04
  • CPU: 64-bit based
  • Memory: 8 GB or higher
  • Disk: 15 GB free hard disk space

Install required packages:

sudo apt-get install p7zip-full git make u-boot-tools libxml2-utils bison build-essential gcc-arm-linux-gnueabi g++-arm-linux-gnueabi zlib1g-dev gcc-multilib g++-multilib libc6-dev-i386 lib32z1-dev

Install older Make 3.82 and Java JDK 6:

pushd /tmp
wget https://ftp.gnu.org/gnu/make/make-3.82.tar.gz
tar xfv make-3.82.tar.gz
cd make-3.82
./configure
make
sudo apt purge -y make
sudo ./make install
cd ..
# Please, download jdk-6u45-linux-x64.bin from https://www.oracle.com/java/technologies/javase-java-archive-javase6-downloads.html (requires free login)
chmod +x jdk-6u45-linux-x64.bin 
./jdk-6u45-linux-x64.bin 
sudo mkdir /opt/java/
sudo mv jdk1.6.0_45/ /opt/java/
sudo update-alternatives --install /usr/bin/javac javac /opt/java/jdk1.6.0_45/bin/javac 1
sudo update-alternatives --install /usr/bin/java java /opt/java/jdk1.6.0_45/bin/java 1
sudo update-alternatives --install /usr/bin/javaws javaws /opt/java/jdk1.6.0_45/bin/javaws 1
sudo update-alternatives --config javac
sudo update-alternatives --config java
sudo update-alternatives --config javaws
popd

PineCubes SPI Flash support patch:

From 9316112c37ee86645fd691c6d3352183b95177d8 Mon Sep 17 00:00:00 2001
From: Marek Kraus <gamelaster@outlook.com>
Date: Fri, 8 Jul 2022 21:01:47 +0200
Subject: [PATCH] Add support for xt25f128 SPI Flash

---
drivers/mtd/devices/m25p80.c | 1 +
1 file changed, 1 insertion(+)

diff --git a/drivers/mtd/devices/m25p80.c b/drivers/mtd/devices/m25p80.c
index 31e5795..0f46a4c 100755
--- a/drivers/mtd/devices/m25p80.c
+++ b/drivers/mtd/devices/m25p80.c
@@ -803,6 +803,7 @@ static const struct spi_device_id m25p_ids[] = {
 	{ "w25x64", INFO(0xef3017, 0, 64 * 1024, 128, SECT_4K) },
 	{ "w25q64", INFO(0xef4017, 0, 64 * 1024, 128, SECT_4K) },
 	{ "W25q128", INFO(0xef4018, 0, 64 * 1024, 256, 0) },
+	{ "xt25f128", INFO(0x0b4018, 0, 64 * 1024, 256, SECT_4K) },
 	
 
 	/* Catalyst / On Semiconductor -- non-JEDEC */
-- 
2.7.4

Unpack SDK and then compile and pack the image:

7z x 'PineCube Stock BSP-SDK ver1.0.7z'
mv 'PineCube Stock BSP-SDK ver1.0' pinecube-sdk
cd pinecube-sdk/camdroid
# apply SPI Flash patch above or edit m25p80.c file
source build/envsetup.sh
lunch # select [1] here
mklichee
extract-bsp
make -j3
pack

Compile using Vagrant

You can avoid setting up your machine and just use Vagrant to spin up a development environment in a VM.

Just clone the Elimo Engineering repo and follow the instructions in the readme file

After spinning up the VM, you just need to run the build:

cd pinecube-sdk/camdroid
# apply SPI Flash patch above or edit m25p80.c file
source build/envsetup.sh
lunch # select [1] here
mklichee
extract-bsp
make -j3
pack

Flashing the image

See PhoenixCard for a manual on how to flash Allwinners BSP images.

Board information, schematics and certifications

PineCube mainboard schematic:

PineCube faceboard schematic:

PineCube certifications:

Datasheets for components and peripherals

Allwinner (Sochip) S3 SoC information:

X-Powers AXP209 PMU (Power Management Unit) information:

CMOS camera module information:

LCD touch screen panel information:

Lithium battery information:

WiFi/BT module information: