The PineCone is a BL602 evaluation board, which was developed with the goal to challenge the open source community to achieve blob-free and free and open source WiFi and Bluetooth, see the Nutcracker Challenge.
- CPU: 32-bit RV32IMAFC RISC-V “SiFive E24 Core”
- 128KB ROM
- 276KB SRAM
- 1Kb eFuse
- 2MB Embedded Flash
- Secure boot
- Secure debug
- AES 128/192/256
- TRNG (True Random Number Generator)
- PKA (Public Key Accelerator)
- Wi-Fi 802.11 b/g/n
- Bluetooth® Low Energy 5.0
- Wi-Fi Fast connection with BLE assistance
- Wi-Fi and BLE coexistence
- Wi-Fi Security WPS/WEP/WPA/WPA2/WPA3
- STA, SoftAP and sniffer modes
- Multi-Cloud connectivity
- 2.4 GHz RF transceiver
- Integrated RF balun, PA/LNA
- Package Type:
- 32 pin QFN 4mm x 4mm
- JTAG support (See below for BL602 impact)
|GPIO Pin||JTAG Pin|
BL602 multiplexes four GPIO pins to provide the familiar JTAG lines. See the accompanying table for the default pin mappings.
These are the default JTAG pins in use after a cold boot. However, many pieces of software, including the demo that's installed by default on new PineCones, remap these pins to other functions. You cannot use the default wiring for JTAG while such software is running. This issue is especially prevalent on the PineCone because three of the default JTAG pins are connected to the onboard RGB LED. Nothing about the LED itself interferes with JTAG, but any program that uses the LED will necessarily remap some of the default JTAG pins to be GPIO.
The MaskROM download mode that the BL602 enters when you tie GPIO8 high does not remap the default JTAG pins, and so you can and should use that mode while checking basic functionality of your JTAG adapter.
Note that, just as software can remap the default JTAG pins to be something else, it can also remap other pins to be JTAG. Control over this is quite granular, with 5-6 candidate pins for each individual JTAG signal that can be mapped independently of one another. LEE Lup Yuen has written some sample code showing how to remap the JTAG pins so that your software can use the LED without giving up support for debugging.
Pine64 USB JTAG Adapter information and schematics
PineCone BL602 EVB information and schematics
- Approximate dimensions: 26mm x 43mm
- Board layout:
- PineCone BL602 EVB schematic ver 1.1
- Note: In PineCone revision 1.1 ("BL62B_EVB V1.1" silkscreened on back of board), CC1 and CC2 share one 5.1KΩ resistor. This means the board will fail to power when you use an e-marked USB-C cable like the one that comes with Apple chargers. See this article for details of why this happens. The next schematic design will give each line its own 5.1KΩ resistor as per the USB-C specification.
- The board uses a CH340 Serial/USB adapter. This chip is commonly used in Arduino-class development boards. It is a full speed (12Mbps) USB interface and has vendor ID 0x1a86 with product ID 0x7523.
- The GPIO pins (11, 12, 14, 17) plus the nearby RESET, POWER, and GND pins are all located on one side of the board, on J1 to provide JTAG connection.
Pinenut-01S Module information and schematics
- Pinenut-01S schematic ver 1.01
- PineNut-01S KiCad schematic ver 1.01
- Pinenut-01S GPIO Definition ver 1.0
- USB Programmer adapter for Pinenut-01S schematic ver 1.0
- The default firmware runs the UART at 2000000 bps. It will accept input whilst regularly outputting:
proc_hellow_entry: RISC-V rv32imafc
cur key status:1
Pinenut-12S Module information
Datasheets for components and peripherals
- Bouffalo BL-602 SoC information:
- Bouffalo Lab's official bl_docs repository: should always contain the latest SoC documentation available, in PDF, HTML, and reStructuredText source forms.
- PINE64's bl602-docs repository: contains an archive of all historical datasheets and reference manual PDFs but may lag behind Bouffalo's official repository. If you notice that it is, please submit a pull request!
- USB/Serial adapter:
Planned to be available in at least three form factors:
- NUT-01S -> ESP-01S
- NUT-12S -> ESP-12S
- NUT-15 -> RTL8723/AMPAK
To load code, you must move the jumper to the position closest to the edge, press reset, load the code, move the jumper back toward the center of the board, and press reset again.
There are currently a number of loaders in progress, each with differing degrees of completeness and success on various operating systems.
- In the build tree, there is BLFlashCube for Windows, which is a proprietary GUI for flashing images. Linux and macOS binaries are available via Bouffalo Lab's developer portal.
- bl60x-flash is in Python and has been reported successful on MacOS catalina (10.15.6) by Punnerud and madushan1000.
- BLOpenFlasher is a WIP, written in go, by Bouffalo Labs to provide source for a flash utility.
- bl602tool is a Python utility in development.
Bouffalo's Python Flash Loader is a new (Dec 20) flash loader by the makers of the chip. Bouffalo's image build smooshes code and adds headers for downloads.
- Bouffalo's MCU tool (Mar 2021) Python image tool replaced both of the above. Now combined with eflash loader, deals with partitions, DTS, signing, fuses etc.
- blflash serial flasher BL602 serial flasher, inspired by BLOpenFlasher
- PineCone BL602 GitHub Page (PINE64 fork) has compilers, linkers, and all the code to build on Windows, Linux (x86_64), and MacOS.
- Bouffalo Lab GitHub Page
- BL602 Developer organize documentation GitHub Page
- BL602 Developer organize tool GitHub Page
- Programming tool for Bouffalo Labs BL602/BL604 chips
- BL602 reverse engineering working group
- Linux kernel module
- BL602 Documentation
- BL602 serial flasher
- Awesome Bouffalo
Articles and Blogs
- Quick Peek of PineCone BL602 RISC-V Evaluation Board by Lup Yuen
- Documenting the BouffaloLab BL602 firmware image format by MK
- Connect PineCone BL602 to OpenOCD by Lup Yuen
- Debug Rust on PineCone BL602 with VSCode and GDB by Lup Yuen
- Porting Mynewt to PineCone BL602 by Lup Yuen
- Flashing Firmware to PineCone BL602 by Lup Yuen
- Control PineCone BL602 RGB LED with GPIO and PWM by Lup Yuen
- Mynewt GPIO ported to PineCone BL602 RISC-V Board by Lup Yuen
- PineCone BL602 talks to I2C Sensors by Lup Yuen
- PineCone BL602 talks SPI too! by Lup Yuen
- PineCone BL602 Blasting Pixels to ST7789 Display with LVGL Library by Lup Yuen
- PineCone BL602 Talks UART to Grove E-Ink Display by Lup Yuen
- The RISC-V BL602 Book by Lup Yuen
- Connect PineCone BL602 to LoRa Transceiver by Lup Yuen
- RAKwireless WisBlock talks LoRa with PineCone BL602 RISC-V Board by Lup Yuen
- PineCone BL602 RISC-V Board Receives LoRa Packets by Lup Yuen
- Run Rust RISC-V Firmware with BL602 IoT SDK by Lup Yuen
- PineCone BL602 Talks LoRaWAN by Lup Yuen
- uLisp and Blockly on PineCone BL602 RISC-V Board by Lup Yuen
- Simulate RISC-V BL602 with WebAssembly, uLisp and Blockly by Lup Yuen
- BL602 Bootloader by Lup Yuen
- Machine Learning on RISC-V BL602 with TensorFlow Lite by Lup Yuen
- Reverse Engineering WiFi on RISC-V BL602 by Lup Yuen
- Rust on RISC-V BL602: Is It Sunny? by Lup Yuen
- Rust on RISC-V BL602: Simulated with WebAssembly by Lup Yuen
- PineDio Stack BL604 RISC-V Board: Testing The Prototype by Lup Yuen
- Rust on RISC-V BL602: Rhai Scripting by Lup Yuen
- LoRaWAN on PineDio Stack BL604 RISC-V Board by Lup Yuen
- The Things Network on PineDio Stack BL604 RISC-V Board by Lup Yuen
- Encode Sensor Data with CBOR on BL602 by Lup Yuen
- IoT Digital Twin with Roblox and The Things Network by Lup Yuen
- Internal Temperature Sensor on BL602 by Lup Yuen
- CBOR Payload Formatter for The Things Network by Lup Yuen
- Monitor IoT Devices in The Things Network with Prometheus and Grafana by Lup Yuen
- Apache NuttX OS on RISC-V BL602 and BL604 by Lup Yuen