Difference between revisions of "POT"

From PINE64
Jump to navigation Jump to search
Line 1: Line 1:
== ''' Peripheral On Top (POT) '''==
''' Peripheral On Top (POT) '''
'''USB/UART Programming Adapter (PMPROG01)'''
=='''USB/UART Programming/Console Adapter (PMPROG01)'''==
   [[File:USB_Prog.JPG]]
   [[File:USB_Prog.JPG]]
   ''Feature''
   ''Feature''
Line 18: Line 18:
   [[http://www.silabs.com/products/mcu/Pages/USBXpress.aspx USBXpress Driver]]
   [[http://www.silabs.com/products/mcu/Pages/USBXpress.aspx USBXpress Driver]]


'''Veroboard POT (PMVRB01)'''
=='''POT: Veroboard (PMVRB01)'''==
   [[File:PMVRB01_board_layout.JPG]]
   [[File:PMVRB01_board_layout.JPG]]
   ''Feature''
   ''Feature''
Line 29: Line 29:
    
    


'''Multi I2C Bus POT (PMI2C01)'''
=='''POT: Multi I2C Bus (PMI2C01)'''==
   [[File:PMI2C01_Board_Layout.JPG]]
   [[File:PMI2C01_Board_Layout.JPG]]
   ''Feature''
   ''Feature''
Line 40: Line 40:
   On Board separated 3.3V supply regulator for 3.3V I2C Bus  
   On Board separated 3.3V supply regulator for 3.3V I2C Bus  
   Each I2C bus pin are protected with ESD protector devices
   Each I2C bus pin are protected with ESD protector devices
   Each channel consist of 4 pcs of XH 4 pin 2.54 mm pitch connector and 2 pcs of XH 5 pin 2.54 mm pitch connector
   Each channel consist of 4 pcs of XH 4 pin 2.54mm pitch connector and 2 pcs of XH 5 pin 2.54mm pitch connector
   For the XH 4 pin connector, will consist of GND,SCL,SDA,5V pin
   For the XH 4 pin connector, will consist of GND,SCL,SDA,5V pin
   For the XH 5 pin connector, will consist of GND,nINT,SCL,SDA,5V pin
   For the XH 5 pin connector, will consist of GND,nINT,SCL,SDA,5V pin
Line 51: Line 51:
   [http://www.nxp.com/documents/application_note/AN11075.pdf NXP AN11075 Driving I2C-bus signals over twisted pair cables with PCA9605]
   [http://www.nxp.com/documents/application_note/AN11075.pdf NXP AN11075 Driving I2C-bus signals over twisted pair cables with PCA9605]


'''I2C Device : Humidity and Temperature Sensor (PMSDP01)'''
=='''POT: ZWave Module (PMZW01)'''==
  [[File:ZWave_PCB_Layout.JPG]]
  Base on Mitsumi WML-C85C ZWave Chipset
  On board PCB antenna or U-FL connector for external antenna
 
=='''I2C Device: Humidity and Temperature Sensor (PMSDP01)'''==
   [[File:PMSDO01_Dew_Point_Sensor.JPG]]
   [[File:PMSDO01_Dew_Point_Sensor.JPG]]
   ''Feature''
   ''Feature''
Line 63: Line 68:
   ''Related Specification and Document''
   ''Related Specification and Document''
   [https://www.silabs.com/Support%20Documents/TechnicalDocs/Si7021-A20.pdf Si7021-A20 Datasheet]
   [https://www.silabs.com/Support%20Documents/TechnicalDocs/Si7021-A20.pdf Si7021-A20 Datasheet]
'''ZWave Module (PMZW01)'''
  [[File:ZWave_PCB_Layout.JPG]]
  Base on Mitsumi WML-C85C ZWave Chipset
  On board PCB antenna or U-FL connector for external antenna

Revision as of 01:32, 7 January 2016

Peripheral On Top (POT)

USB/UART Programming/Console Adapter (PMPROG01)

 USB Prog.JPG
 Feature
 Base on Silicon Libs CP2102
 Support Virtual COM Port Device Drivers
 Support USBXpress™ Direct Driver Support
 With XH 5 pin 2.54mm pitch connector for UART connection
 Voltage Output on the connection is selectable to either 5V,3.3V or off
 On board USB-B Connector Receptor
 Connector J3 can direct insert into Pine A64 Exp-Bus
 I/O pin are protected with ESD protector IC.
 On board 5x2pin connector can direct insert into Pine A64 Exp Bus for UART0 Console access
 
 Related Specification and Document
 [CP2102 Datasheet]
 [Virtual COM Port Driver]
 [USBXpress Driver]

POT: Veroboard (PMVRB01)

 PMVRB01 board layout.JPG
 Feature
 Sit on top of Pine A64 board
 All the header receptor will have extended length pin to allow other POT board to insert on top of it
 Allow easy access to all the I/O pin on the Pine A64 header
 On board 4pcs of LED with current limiting resistor all direct connect to I/O pin for status indicator
 On board 4pcs of Tact switch
 On board XH5 2.54mm pitch connector for UART0 allow easy connection to USB/UART adapter for console access
 

POT: Multi I2C Bus (PMI2C01)

 PMI2C01 Board Layout.JPG
 Feature
 Sit on top of Pine A64 board
 All the header receptor will have extended length pin to allow other POT board to insert on top of it
 Allow easy access to all the I/O pin on the Pine A64 header
 2 channel of I2C bus is wire out for easy access
 I2C bus repeater IC (PCA9517A) are included in each I2C bus to allow connection of more devices on each bus
 Support 3.3V and 5V I2C bus for each channel separately
 On Board separated 3.3V supply regulator for 3.3V I2C Bus 
 Each I2C bus pin are protected with ESD protector devices
 Each channel consist of 4 pcs of XH 4 pin 2.54mm pitch connector and 2 pcs of XH 5 pin 2.54mm pitch connector
 For the XH 4 pin connector, will consist of GND,SCL,SDA,5V pin
 For the XH 5 pin connector, will consist of GND,nINT,SCL,SDA,5V pin
 5V supplier is direct connect from Pine A64 adapter's supply thus prevent over loading Pine A64 board
 The nINT pin will allow peripheral with interrupt pin link back to the Pine A64 I/O pin
 
 Related Specification and Document
 NXP PCA9517A Datasheet
 NXP AN10658 Sending I2C-bus signal via long communication cables
 NXP AN11075 Driving I2C-bus signals over twisted pair cables with PCA9605

POT: ZWave Module (PMZW01)

 ZWave PCB Layout.JPG
 Base on Mitsumi WML-C85C ZWave Chipset
 On board PCB antenna or U-FL connector for external antenna

I2C Device: Humidity and Temperature Sensor (PMSDP01)

 PMSDO01 Dew Point Sensor.JPG
 Feature
 Base on Silicon Labs Si7021 I2C Humidity and Temperature Sensor
 High Accuracy Temperature Sensor ±0.4 °C (max), –10 to 85 °C
 0 to 100% RH operating range
 Up to –40 to +125 °C operating range
 On board 3.3V regulator
 2pcs of XH 4pin 2.54 mm pitch connector to allow daisy chain of multiple I2C sensor
 
 Related Specification and Document
 Si7021-A20 Datasheet