Overclocking

This might damage your equipment or may result in a unstable system, so do this at your own risk!

This page is incomplete, you're welcome to improve it.

Overclocked devices may seem stable but crash occasionally and be hard to debug. A good test suite needs to be found to properly test the entire functionality of overclocked devices to properly ensure stability

Keep a backup bootable OS which is known to be stable, if an overclock fails you may not be able to boot the system without another OS

All information regarding clock speeds, voltages and more are stored in the DTB (Device Tree Blob). You can learn more about it here.

Overclocking is a way to get more and better performance out of the system by running it at higher clock speeds than the factory default.

Preparation

TODO, requires a compatible cross compiler (usually aarch64-linux-gnu), and clone the pine64 kernel repository.

Then after that just setup the variables for make.

A64-based boards

GPU

Open arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi in a text editor.

Look for

		mali: gpu@1c40000 {
			compatible = "allwinner,sun50i-a64-mali", "arm,mali-400";
			reg = <0x01c40000 0x10000>;
			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "gp",
					  "gpmmu",
					  "pp0",
					  "ppmmu0",
					  "pp1",
					  "ppmmu1",
					  "pmu";
			clocks = <&ccu CLK_BUS_GPU>, <&ccu CLK_GPU>;
			clock-names = "bus", "core";
			resets = <&ccu RST_BUS_GPU>;

			assigned-clocks = <&ccu CLK_GPU>;
			assigned-clock-rates = <432000000>;
		};

The assigned-clock-rates line is set to 432000000, this means that the GPU is clocked at 432MHz. So if you want 500MHz, set the value to 500000000.

Save the dtsi file, and recompile the DTB.

Danct12 has found on his Pinetab that 562 MHz is the limit for stable operation.

Remember to run a benchmark tool (such as glmark2-es2) to make sure that it's stable! If it's not, then lower the clock speed until you can get a stable clock speed.

CPU

TODO

DRAM

It is not recommended to exceed 672 MHz clockspeed on the DRAM.

When overclocking the GPU, it is a good idea to also overclock the DRAM, as the main bottleneck of the A64 SOC is the memory.

Rockchip RK3399 based boards

The RK3399 clocks are found in arch/arm64/boot/dts/rockchip/rk3399-opp.dtsi

More optimised voltages and clocks can be found in arch/arm64/boot/dts/rockchip/rk3399-op1-opp.dtsi These include a slight overclock and undervolt, they are intended for the OP1 CPU found in many chromebooks but have worked fine in all recorded cases on regular RK3399s in other devices.

Any clock speeds can be added for the GPU in gpu_opp_table A set of available clock speeds that can be added to the CPU clusters can be found in [need to fine file], these clock speeds can be added to cluster0_opp for the small cores and cluster1_opp for the big cores respectively

Safe voltages for the GPU and small CPU core clusters are up to 1.2V.

Safe voltages for the big CPU core cluster is up to 1.25V.

These are specified in the RK3399 schematic provided by Rockchip as being the maximum recommended operating voltage.

TuxThePenguin has found that the RK3399 in his Pinebook Pro can reach 950MHz on the GPU while being stable, 1GHz was tried but crashed instantly.

Rockchip RK3328 based boards

TODO