Difference between revisions of "Project Anakin"

From PINE64

Jump to navigation Jump to search

Revision as of 22:53, 13 November 2018

Setting Up Your device - What You’ll Need to Get Started

You will need the following to get started with using your PINE A64(+), SOPine/PINE A64-LTS, Pinebook or ROCK64 board:

Windows / Linux PC or MAC with a SD Card Reader connected to the Internet.
For PINE A64(+): Power Supply (PSU) and a micro usb cable. Please make sure to use a PSU rated at +5V @2A and a micro USB cable that is at least 26 AWG thick.
For SOPine/PINE A64-LTS: Power Supply (PSU) with 3.5mm OD/1.5mm ID barrel DC Jack. Please make sure to use a PSU rated at +5V @2A.
For Pinebook and ROCK64: Power Supply (PSU) with 3.5mm OD/1.5mm ID barrel DC Jack. Please make sure to use a PSU rated at +5V @3A.
MicroSD card (8GB or higher capacity) rated 'class 10' or better.
HDMI cable (unless you wish to run headless / without a monitor). On A64 Devices Android and Remix OS support 720p and 1080p, while Linux supports a wider range of resolutions.
Input device(s) such as: keyboard, mouse, remote, pointer, etc.

A One-Step Solution to Flashing Your MicroSD Card

Please try our PINE64 Installer to easily select the PINE A64(+), SOPINE/PINE A64-LTS, Pinebook or ROCK64 OS of your choice and flash it to your MicroSD Card.

You can also flash an OS image manually; please follow the instructions below.

Software and OS Image Downloads

Project Anakin

Under the 'SOPINE Software and OS Image Download Section' you can find a complete list of currently supported Mainline Linux Operating System images that work with the Akakin project as well as other related software. The list includes OS images and descriptions of:

Arch Linux mainline XFCE

These images should be used at your own risk and are not fit for normal use

Mali-400 64-bit Driver

Mali-400 64-bit Driver [20171220]

Mali 64-bit X11 and Wayland Driver Download

Accessories Step-by-Step Guides

Under 'Guides for PINE A64(+) accessories' you can find instructions and guides concerning:

Playbox Enclosure
Bluetooth and WiFi module
7" Touch Screen LCD Panel

SoC and Memory Specification

Based on Allwinner A64/R18
- R18 and A64 are identical SoC but R18 committed for 10 years supply by vendor.

CPU Architecture

Quad-core ARM Cortex-A53 Processor@1152Mhz
A power-efficient ARM v8 architecture
64 and 32bit execution states for scalable high performance
Support NEON Advanced SIMD (Single Instruction Multiple Data) instruction for acceleration of media and signal processing function
Support Large Physical Address Extensions(LPAE)
VFPv4 Floating Point Unit
32KB L1 Instruction cache and 32KB L1 Data cache
512KB L2 cache

GPU Architecture

ARM Mali400MP2 Dual-core GPU
Support OpenGL ES 2.0 and OpenVG 1.1 standard

System Memory

RAM Memory Variants: 2GB LPDDR3.
Storage Memory: SPI Flash and optional eMMC module from 16GB up to 64GB

Project Anakin, SOPine Module and Baseboard Information, Schematics, and Certifications

Model "A" Baseoard Dimensions: 133mm x 80mm x 19mm
Input Power: DC 5V @ 2A, 3.7V Li-Ion battery connector, 3.5OD/1.35ID Barrel DC Jack connector, Euler connector
PINE A64 Connector Layout @courtesy of norm24
PINE A64 Connector List
SOPine Module Pin Assignment ver 1.0
PINE A64 Pi-2/Eular/Ext Bus/Wifi Bus Connector Pin Assignment (Updated 15/Feb/2016)
- Good documentation about PINE A64, A64+, and A64-LTS GPIO pins article
SOPine Module Schematic:
- SOPine Module Schematic
SOPine Model "A" Baseboard Schematic and PCB Board Resource:
- SOPine model "A" Baseboard is an hardware open source project but is not "OSH" compliance.:
- SOPine Model "A" Baseboard Schematic capture Rev B DSN source file
- SOPine Model "A" Baseboard Schematic Rev B PDF file
- SOPine Model "A" Baseboard PCB Job source file
- SOPine Model "A" Baseboard PCB Gerber file
- SOPine Model "A" Baseboard PCB Layout PDF file
- SOPine with model "A" baseboard FCC Certificate
- SOPine with model "A" baseboard CE Certificate
- SOPine with model "A" baseboard RoHS Certificate

Datasheets for Components and Peripherals

Allwinner A64/R18 SoC information:
- R18 and A64 are identical SoC but R18 committed for 10 years supply by vendor.
- Allwinner A64 SoC Brief Introduction
- Allwinner R18 SoC Brief Introduction
- Allwinner A64/R18 SoC Data Sheet V1.1 (Official Released Version)
- Allwinner A64/R18 SoC User Manual V1.0 (Official Release Version)
X-Powers AXP803 PMU (Power Management Unit) information:
- AXP803 PMIC Datasheet
LPDDR3 information:
eMMC information:
SPI NOR Flash information:
- WinBond 128Mb SPI Flash Datasheet
- GigaDevice 128Mb SPI Flash Datasheet
Project Anakin module/component related information:
- 5MPixel Rear CMOS Camera module information:
- LCD Touch Screen Panel information:
- Lithium Battery information:
  - 8000mAH Lithium Battery Specification
- Ethernet PHY information:
  - Realtek RTL8211 10/100/1000M Ethernet Transceiver for PINE A64+ Board
  - Realtek RTL8201 10/100M Ethernet Transceiver for PINE A64 Board
- Wifi/BT module information:
  - Realtek RTL8723BS WiFi with BT SDIO
- Enclosure information:
  - Playbox Enclosure 3D file
- Connector information:
  - 2.0mm PH Type connector specification use in Lithium Battery (VBAT) port and RTC Battery port
  - 0.5mm Pitch cover type FPC connector specification use in DSI port, TP port and CSI port
- LTE module information:
  - Note: The current Project Anakin kit deploy on using Quectel EC20_R2.1 which belong to EC25 family. Actually production will use EC25 and EG25-G (still preliminary) module pending on region.
  - Quectel EC20 R2.1 LTE Module Specification
  - Quectel EC25 LTE Module Specification
  - Quectel EG25-G LTE Module Specification
  - Quectel EC25 LTE Module AT Cammands Set Manual
  - Quectel EC25 LTE Module Hardware Design Guide
  - Quectel EC25 LTE Module Reference Design Guide

Other Resources

Retrieved from "https://wiki.pine64.org/index.php?title=Project_Anakin&oldid=3068"