ROCK64 - Revision history

Dsimic: /* Information, Schematics and Certifications */ Linked the datasheet

2024-11-21T19:08:53Z

Information, Schematics and Certifications: Linked the datasheet

← Older revision		Revision as of 19:08, 21 November 2024
Line 223:		Line 223:

	== Information, Schematics and Certifications ==		== Information, Schematics and Certifications ==
	{{Warning\|While it's also possible to power the ROCK64 from the pins on the GPIO header, doing that isn't advisable because the inductor that's placed in series with that power input is rated for up to 1.5 A when the temperature of its case is below 85 oC. If you can guarantee not to go above those ratings, it may work reliably, otherwise you risk damage to your board.}}		{{Warning\|While it's also possible to power the ROCK64 from the pins on the GPIO header, doing that isn't advisable because the [[:File:Murata-manufacturing-blm18pg181sn1-datasheet-r2024.pdf\|Murata BLM18PG181SN1]] inductor that's placed in series with that power input is rated for up to 1.5 A when the temperature of its case is below 85 oC. If you can guarantee not to go above those ratings, it may work reliably, otherwise you risk damage to your board.}}

	Board dimensions: 85 x 56 x 18.8 mm, see the [https://files.pine64.org/doc/rock64/rock64%20board%20dimension.pdf ROCK64 board dimension drawing]		Board dimensions: 85 x 56 x 18.8 mm, see the [https://files.pine64.org/doc/rock64/rock64%20board%20dimension.pdf ROCK64 board dimension drawing]

Dsimic: /* Information, Schematics and Certifications */ Ditto

2024-11-21T18:47:38Z

Information, Schematics and Certifications: Ditto

← Older revision		Revision as of 18:47, 21 November 2024
Line 223:		Line 223:

	== Information, Schematics and Certifications ==		== Information, Schematics and Certifications ==
	{{Warning\|While it's also possible to power the ROCK64 from the pins on the GPIO header, doing that isn't advisable because the inductor that's placed in series with that power input is rated for up to 1.5 A when the temperature of its case is below 85 oC. If you can guarantee not to go above those ratings, it may work reliably.}}		{{Warning\|While it's also possible to power the ROCK64 from the pins on the GPIO header, doing that isn't advisable because the inductor that's placed in series with that power input is rated for up to 1.5 A when the temperature of its case is below 85 oC. If you can guarantee not to go above those ratings, it may work reliably, otherwise you risk damage to your board.}}

	Board dimensions: 85 x 56 x 18.8 mm, see the [https://files.pine64.org/doc/rock64/rock64%20board%20dimension.pdf ROCK64 board dimension drawing]		Board dimensions: 85 x 56 x 18.8 mm, see the [https://files.pine64.org/doc/rock64/rock64%20board%20dimension.pdf ROCK64 board dimension drawing]

Dsimic: /* Information, Schematics and Certifications */ Wording improvements

2024-11-21T18:46:57Z

Information, Schematics and Certifications: Wording improvements

← Older revision		Revision as of 18:46, 21 November 2024
Line 223:		Line 223:

	== Information, Schematics and Certifications ==		== Information, Schematics and Certifications ==
	{{Warning\|While it's also possible to power the ROCK64 from the pins on the GPIO header, doing that isn't advisable because the inductor that's placed in series with that power input is rated for up to 1.5 A below 85 oC ~~of its case temperature~~. If you can guarantee not to go above those ratings, it may work reliably.}}		{{Warning\|While it's also possible to power the ROCK64 from the pins on the GPIO header, doing that isn't advisable because the inductor that's placed in series with that power input is rated for up to 1.5 A when the temperature of its case is below 85 oC. If you can guarantee not to go above those ratings, it may work reliably.}}

	Board dimensions: 85 x 56 x 18.8 mm, see the [https://files.pine64.org/doc/rock64/rock64%20board%20dimension.pdf ROCK64 board dimension drawing]		Board dimensions: 85 x 56 x 18.8 mm, see the [https://files.pine64.org/doc/rock64/rock64%20board%20dimension.pdf ROCK64 board dimension drawing]

Dsimic: /* Information, Schematics and Certifications */ Described the GPIO power input

2024-11-21T18:46:04Z

Information, Schematics and Certifications: Described the GPIO power input

← Older revision		Revision as of 18:46, 21 November 2024
Line 223:		Line 223:

	== Information, Schematics and Certifications ==		== Information, Schematics and Certifications ==
			{{Warning\|While it's also possible to power the ROCK64 from the pins on the GPIO header, doing that isn't advisable because the inductor that's placed in series with that power input is rated for up to 1.5 A below 85 oC of its case temperature. If you can guarantee not to go above those ratings, it may work reliably.}}

	Board dimensions: 85 x 56 x 18.8 mm, see the [https://files.pine64.org/doc/rock64/rock64%20board%20dimension.pdf ROCK64 board dimension drawing]		Board dimensions: 85 x 56 x 18.8 mm, see the [https://files.pine64.org/doc/rock64/rock64%20board%20dimension.pdf ROCK64 board dimension drawing]

Dsimic: /* Information, Schematics and Certifications */ Small cleanups and improvements

2024-09-17T13:19:58Z

Information, Schematics and Certifications: Small cleanups and improvements

← Older revision		Revision as of 13:19, 17 September 2024
Line 223:		Line 223:

	== Information, Schematics and Certifications ==		== Information, Schematics and Certifications ==
	Board ~~Dimensions~~: ~~85mm~~ x ~~56mm~~ x 18.~~8mm~~, see the [https://files.pine64.org/doc/rock64/rock64%20board%20dimension.pdf ROCK64 board dimension drawing]		Board dimensions: 85 x 56 x 18.8 mm, see the [https://files.pine64.org/doc/rock64/rock64%20board%20dimension.pdf ROCK64 board dimension drawing]

	~~Input~~ Power: ~~+5V @3A with~~ 3.~~5mm~~/1.~~35mm Type~~ H ~~Barrel type DC~~ connector (~~@2A~~ will work if there is no heavy load on the USB 3.0 port)		Power input: 3 A at 5 V DC, using 3.5 mm OD / 1.35 mm ID type H barrel connector (also known as DC 35135, 2 A at 5 V will work if there is no heavy load on the USB 3.0 port)

	ROCK64 ver 3.0 SBC related info:		ROCK64 ver 3.0 SBC related info:

Dsimic: /* Upstreaming Status */ Added a warning

2023-10-23T08:07:34Z

Upstreaming Status: Added a warning

← Older revision		Revision as of 08:07, 23 October 2023
Line 49:		Line 49:

	== Upstreaming Status ==		== Upstreaming Status ==
			{{Warning\|The data presented in this section requires updating.}}

	{\| class="wikitable plainrowheaders" border="1"		{\| class="wikitable plainrowheaders" border="1"

Dsimic: /* Storage */ Small cleanup

2023-10-23T07:49:47Z

Storage: Small cleanup

← Older revision		Revision as of 07:49, 23 October 2023
Line 213:		Line 213:
	* 2 USB2.0 Dedicated Host port (top one is USB-OTG)		* 2 USB2.0 Dedicated Host port (top one is USB-OTG)

	Optionally installed eMMC module can be disabled by placing a jumper onto the pins on the separate two-pin header, located near one of the mounting holes and two side-mounted buttons. See the picture in this section, in which this two-pin header is highlighted in red.		Optionally installed eMMC module can be disabled by placing a jumper onto the two pins on the separate two-pin header, located near one of the mounting holes and two side-mounted buttons. See the picture in this section, in which this two-pin header is highlighted in red.

	=== Expansion Ports ===		=== Expansion Ports ===

Dsimic: /* Storage */ Described the jumper for disabling the eMMC

2023-10-23T07:49:11Z

Storage: Described the jumper for disabling the eMMC

← Older revision		Revision as of 07:49, 23 October 2023
Line 205:		Line 205:

	=== Storage ===		=== Storage ===
			[[File:Rock64-emmc-disable-jumper.png\|250px\|thumb\|right\|Position of the two-pin header for disabling the optionally installed eMMC module (highlighted in red)]]

	* microSD - bootable, supports SDHC and SDXC and storage up to 256GB		* microSD - bootable, supports SDHC and SDXC and storage up to 256GB
	* eMMC - bootable (optional eMMC Module)		* eMMC - bootable (optional eMMC Module)
Line 210:		Line 212:
	* 1 USB3.0 Dedicated Host port		* 1 USB3.0 Dedicated Host port
	* 2 USB2.0 Dedicated Host port (top one is USB-OTG)		* 2 USB2.0 Dedicated Host port (top one is USB-OTG)

			Optionally installed eMMC module can be disabled by placing a jumper onto the pins on the separate two-pin header, located near one of the mounting holes and two side-mounted buttons. See the picture in this section, in which this two-pin header is highlighted in red.

	=== Expansion Ports ===		=== Expansion Ports ===

Pbrobinson: /* Power button doesn't do anything on a short press (Linux) */

2023-06-11T22:59:16Z

Power button doesn't do anything on a short press (Linux)

← Older revision		Revision as of 22:59, 11 June 2023
Line 305:		Line 305:
	=== Power button doesn't do anything on a short press (Linux) ===		=== Power button doesn't do anything on a short press (Linux) ===

	Make sure the <code>rk805_pwrkey</code> module is loaded, e.g. with <code>lsmod \| grep rk805_pwrkey</code>. If it doesn't show up, do a <code>modprobe rk805_pwrkey</code> as root. To make this persistent, create a <code>99-rk805_pwrkey.conf</code> in <code>/etc/modules-load.d/</code> with the content <code>rk805_pwrkey</code>		Make sure the <code>rk805_pwrkey</code> module is loaded, e.g. with <code>lsmod \| grep rk805_pwrkey</code>. The module auto loading of <code>rk805_pwrkey</code> was fixed in the following upstream kernels: v6.0/v5.15.66/v5.10.142/v5.4.213/v4.19.258/v4.14.293 so there should be no requirement for fixes with those kernels or newer. If it doesn't show up, do a <code>modprobe rk805_pwrkey</code> as root. To make this persistent, create a <code>99-rk805_pwrkey.conf</code> in <code>/etc/modules-load.d/</code> with the content <code>rk805_pwrkey</code>

	If it still doesn't work, make sure your init system is actually listening to the button press. With systemd, check <code>/etc/systemd/logind.conf</code> and make sure it's either all commented out (uses defaults) or contains something like <code>HandlePowerKey=poweroff</code>. You can change the short press action by setting <code>HandlePowerKey</code> to one of "ignore", "poweroff", "reboot", "halt", "kexec", "suspend", "hibernate", "hybrid-sleep", "suspend-then-hibernate", or "lock".		If it still doesn't work, make sure your init system is actually listening to the button press. With systemd, check <code>/etc/systemd/logind.conf</code> and make sure it's either all commented out (uses defaults) or contains something like <code>HandlePowerKey=poweroff</code>. You can change the short press action by setting <code>HandlePowerKey</code> to one of "ignore", "poweroff", "reboot", "halt", "kexec", "suspend", "hibernate", "hybrid-sleep", "suspend-then-hibernate", or "lock".

Fxc: /* Guides */ Deprecating the guides. Too OS-dependent, outside the scope of the wiki

2023-02-05T13:19:26Z

Guides: Deprecating the guides. Too OS-dependent, outside the scope of the wiki

← Older revision		Revision as of 13:19, 5 February 2023
Line 314:		Line 314:

	[[User:CounterPillow]] submitted [https://overviewer.org/~pillow/up/c5179dcb67/0001-rockchip-rk3328-Set-VOP-QoS-to-high-priority.patch a patch] to u-boot to fix this, but someone still needs to write a kernel patch to save/restore the QoS registers from the power domain driver.		[[User:CounterPillow]] submitted [https://overviewer.org/~pillow/up/c5179dcb67/0001-rockchip-rk3328-Set-VOP-QoS-to-high-priority.patch a patch] to u-boot to fix this, but someone still needs to write a kernel patch to save/restore the QoS registers from the power domain driver.

	~~== Guides ==~~
	~~This topic has several guides to show readers how to perform useful and common tasks on their system.~~
	* [[Guide:Locating your device]]
	* [[Guide:Connecting to your device with SSH]]
	* [[Guide:Setting up a Hostname]]
	* [[Guide:Setting up a Static IP and DNS]]
	* [[Guide:Adding USB storage to your Device and Formatting it for linux]]
	* [[Guide:Setting up an SMB (Windows) file server]]

	== Other Resources ==		== Other Resources ==