PINE64 - User contributions [en]

PinePhone

2020-12-05T22:40:21Z

Zebulon Walton:

The PinePhone is a smartphone created by Pine64, capable of running mainline Linux and supported by many partner projects. The BraveHeart Edition was the first publicly-available version of the phone, though it came without a fully functional OS (factory test image) and was geared specifically towards tinkerers and hackers. Its successor is the Community Edition, the first Community Edition started to ship in June 2020. The phone will be available for at least five years.

== First time installation ==

{{Hint|The default PIN for the Manjaro Community Edition is '''123456'''.}}

[[File:PinePhone-3.jpg|400px|thumb|right|PinePhone is capable of running a multitude of different Linux mobile OSes]]

[[File:Pinephone_rendering_blank.png|400px|thumb|right|Rendering of the back and front of PinePhone]]

From the factory the battery has a sticker on it that isolates the battery from the phone. The battery '''will not''' charge until this is removed.

[[File:Pinephone_warning.png|none|left|400px]]

After unboxing remove the back panel using the notch in the corner of the back panel. Then remove the battery and peel off the clear plastic sticker below it that isolates the charging contact. Then replace the battery, see [[PinePhone#Battery|Battery]] for more information.

The SIM card has to be placed in the lower slot, while the microSD has to be placed in the upper slot, as pictured here:

[[File:Pinephone_backside.png|none|left|400px]]

== Specifications ==

'''Dimensions:''' 160.5 x 76.6 x 9.2mm 
'''Weight:''' Between 180-200 grams 
'''SIM Card:''' Micro-SIM 
'''Display:'''
: '''Size:''' 5.95 inches (151mm) diagonal
: '''Type:''' HD IPS capacitive touchscreen, 16M colors
: '''Resolution:''' 1440x720, 18:9 ratio 
'''System on Chip:''' [https://linux-sunxi.org/A64 Allwinner A64] 
'''RAM:''' 2GB or 3GB LPDDR3 SDRAM 
'''Internal Storage:''' 16GB or 32GB eMMC, extendable up to 2TB via microSD, supports SDHC and SDXC 
'''Back Camera:''' Single 5MP, 1/4", LED Flash 
'''Selfie Camera:''' Single 2MP, f/2.8, 1/5" 
'''Sound:''' Loudspeaker, 3.5mm jack & mic (jack doubles as hardware UART if killswitch 6 is deactivated) 
'''Communication: G25-G'''
: '''LTE:''' B1, B2, B3, B4, B5, B7, B8, B12, B13, B18, B19, B20, B25, B26, B28, B38, B39, B40, B41
: '''WCDMA:''' B1, B2, B4, B5, B6, B8, B19
: '''GSM:''' 850, 900, 1800, 1900 (MHz)
: '''WLAN:''' Wi-Fi 802.11 b/g/n, single-band, hotspot
: '''Bluetooth:''' 4.0, A2DP
: '''GNSS:''' GPS/GLONASS/BeiDou/Galileo/QZSS, with A-GPS
'''Sensors:''' Accelerometer, gyro, proximity, ambient light, compass 
'''Killswitches:''' Modem, WiFi & Bluetooth, Microphone, Cameras 
'''Battery:''' Lithium-ion, rated capacity 2800mAh (10.64Wh), typical capacity 3000mAh (11.40Wh) (nominally replaceable with any Samsung J7 form-factor battery) 
'''I/O:''' USB Type-C, USB Host, DisplayPort Alternate Mode output, 15W 5V 3A Quick Charge, follows USB PD specification

== Components ==
{| class="wikitable"
! Component
! Model
|-
| Touchscreen
| Goodix GT917S
|-
| Rear camera
| OmniVision OV5640
|-
| Camera flash
| SGMICRO SGM3140
|-
| Front camera
| GalaxyCore GC2145
|-
| LCD
| Xingbangda XBD599
|-
| WiFi
| Realtek RTL8723CS
|-
| Bluetooth
| Realtek RTL8723CS
|-
| Modem
| Quectel EG25-G
|-
| GNSS/GPS
| Quectel EG25-G
|-
| Magnetometer
| ST LIS3MDL
|-
| Ambient light / Proximity
| SensorTek STK3335
|-
| Sixaxis
| InvenSense MPU-6050
|-
| Vibration motor
| Unknown model
|-
| Notification LED
| LED0603RGB
|-
| Volume buttons
| Buttons connected to the KEYADC
|-
| Power button
| X-Powers AXP803
|-
| Battery fuel gauge
| X-Powers AXP803
|}

See the [[PinePhone_component_list|PinePhone Component List]].

== Hardware revisions ==

# [[Project Anakin]]
# [[Project Don't be evil|"Project Don't Be Evil" devkit]]
# [[PinePhone v1.0 - Dev|PinePhone v1.0 - Developer batch]]
# [[PinePhone v1.1 - Braveheart]]
# [[PinePhone v1.2‎]] - Ubports Community Edition
# [[PinePhone v1.2a]] - postmarketOS Community Edition
# [[PinePhone v1.2b]] - Manjaro Community Edition

== Swapping in a new mainboard revision ==

The mainboard can be replaced, for example for upgrading to a newer hardware revision or if it is faulty. The replacement board does not have an OS preinstalled, to test if everything is working after swapping the mainboard a flashed SD card is required. The mainboard also comes with a non-functional firmware on the ANX chip, a newer firmware version has to be flashed as explained below to get certain USB functionality to work.

=== Replacing the mainboard ===

Prior to replacing your PinePhone’s mainboard please read the steps outlined in bullet points below and watch the attached video.

# You’ll need a small Phillip’s screwdriver and a prying tool to swap out the PinePhone’s mainboard.
# Remove the PinePhone’s back cover. See your quick start guide for details.
# Remove the battery as well as any inserted SD and SIM cards.
# Unscrew all 15 Phillip’s head screws around the midframe of the phone.
# Gently pry up the midframe using a guitar pick or credit card corner. It is easiest to separate the midframe at one of the bottom edges. Work your way around all the sides of the phone until the midframe separates from the phone’s body.
# Detach all ribbon cables and “Lego” connectors. List of things to detach: 1) two “Lego” connects at the bottom of the mainboard. 2) u.FL antenna connect and touchscreen digitizer on PCD left side. 3) LCD ribbon cable top of mainboard, next to audio/ UART jack.
# Pry the mainboard up gently from the left-hand side.
# Remove front and main cameras and reset them into the new mainboard.
# Check that the rubber proximity sensor housing is in the chassis, not stuck to the removed mainboard.
# Place the new mainboard in the chassis, hooking in on the plastic tabs on left side and pressing down firmly on opposite side, and follow the steps (7-2) in reverse. When reattaching the midframe take care that no cables are out of place or trapped, as they may be damaged when tightening screws.

After swapping the mainboard the phone won't boot as there is no OS on the replacement board's eMMC preinstalled. To boot an OS insert a flashed SD card.

A video tutorial can be found here:
[[File:Pinephone_martijn_pcb_replacement.png|thumb|none|600px|link=https://www.youtube.com/watch?v=5GbMoZ_zuZs|Watch Martijn Braam's video tutorial here: https://www.youtube.com/watch?v=5GbMoZ_zuZs. Alternatively user bridadan uploaded a video tutorial of the swap procedure including camera swap and proximity sensor housing here: https://www.youtube.com/watch?v=J3AJEF7akkw.]]

=== Flashing the ANX firmware ===

After swapping the mainboard the ANX chip has to be flashed for full USB functionality.

Download the latest ANX firmware image on the phone:

wget https://xff.cz/git/linux-firmware/plain/anx7688-fw.bin

Execute as root ("sudo su") on the phone:

cp anx7688-fw.bin /lib/firmware/
echo 1 > /sys/class/typec/port0/device/flash_eeprom

== Replacing the screen ==

Before attempting to replace the screen be sure to review the section on [[#Swapping in a new mainboard revision|replacing the mainboard]] since that will get you most of the way there. Be aware that the replacement screen is actually the entire front frame of the phone and there are components that will need to be swapped from your old screen.

* Make sure you have a precision screwdriver set that has the correct size Philips tip. The screws are very small and the heads can easily be stripped if the screwdriver is not correct - if you feel your screwdriver slipping, stop what you are doing and try one that is a better fit. A magnetized screwdriver will help in not losing screws, as will a magnetic parts holder to keep them in while working.

* There are a number of components and cables as well as the insulator sheet under the battery that are glued in place. A hair dryer will loosen the glue and make them much easier to remove. You may want to order extra cables along with the screen just in case.

* The vibrator motor, which is part of the USB-C board assembly and glued into place, will come apart easily and be damaged if you pry it up in the wrong place. Make sure you pry from underneath the complete part, not midway on its housing. The ribbon cable attaching this to the USB-C board is small, thin, and fragile so be careful with that as well.

* The new screen comes with new side switches and insulator sheet but there are a number of parts that need to be transferred from the old screen, like the thin coax cable running up the side, the phone ear speaker, proximity sensor gasket, and a gold-colored mesh glued in place that needs to be transferred to a flexible circuit included on the new screen. If you don't swap over the proximity sensor rubber gasket the screen will immediately turn off after logging in. Be careful when routing the coax cable that it goes around the screw holes or you may drive a screw right through the cable.

Take your time, use the right tools, be careful and you should be rewarded with success.

== Hardware accessory ==

=== PinePhone hardware accessory compatibility ===
See [[PinePhone Hardware Accessory Compatibility]] for a list of devices working with the PinePhone (depending on their OS support).

=== USB-C connector ===

The USB-C can be used to power the device, and offers USB2 host and OTG possibilities, and also can make use of the USB-C capability to integrate HDMI signals. Some USB-C hubs are available that offer power throughput, USB connection, HDMI port and Ethernet connection. The driver that would make this connection available is not supported at this time.

=== Pogo pins ===

The PinePhone has 6 pogo pins on the back allowing for custom hardware extensions such as wireless charging, an IR blaster, a keyboard extension or extended battery case. The pogo pins provide access to an interrupt line, power input to charge the battery, power source and an I2C interface.

[[File:Pinephone pogo.png|none|400px]]

{| class="wikitable"
| Interrupt
| SDA
| SCL
|-
| 5V / VBUS
| VBAT
| GND
|}

The VBUS pin is powered by USB and is 5V. The second power pin is VBAT, which connects to the battery voltage. The I2C and interrupt lines have pull-ups on the phone side. The I2C lines are pulled up to 3V3 by the phone.

For a breakout board see [https://github.com/SMR404/PinephonePogoBreakout here]. For an example project see Martijn's blog post [https://blog.brixit.nl/making-a-backcover-extension-for-the-pinephone/ "Making a backcover extension for the PinePhone"].

=== Back cover ===
A step file for the back cover for creating custom cases is freely available [https://files.pine64.org/doc/PinePhone/PinePhone%20Back%20Cover%20ver%200.5.stp here].

=== Serial console ===

The PinePhone has a serial port in the headphone connector, it's activated by the 6th contact on the dipswitch. If the switch is set to "on", the headphone connector is in audio mode, if it is set to "off" it's in UART mode. The UART serial connection can also be used for communication with other devices from the PinePhone.

The UART is 115200n8.

The pinout for the serial connector is:

* Tip: RX
* Ring: TX
* Sleeve: GND

[[File:PinePhone_Serial_Cable.png|none|400px]]

You can buy a serial debug cable from the [https://pine64.com/product/pinebook-pinephone-pinetab-serial-console/ Pine64 Store]. The store cable uses a 4 ring plug, as seen in the [https://files.pine64.org/doc/pinebook/guide/Pinebook_Earphone_Serial_Console_Developer_Guide.pdf here], but a 3 ring plug works just as well. The cable uses a CH340 chipset based serial to USB converter, but any 3.3v serial connection can be used. Because it is a "host"/DTE it means that you need a ''cross modem cable'' ([https://en.wikipedia.org/wiki/Null_modem Null Modem]) with TX on Tip to be connected to RX. A cable like e.g. [https://www.ftdichip.com/Products/Cables/USBTTLSerial.htm FTDI TTL-232R-3V3-AJ] which has TX on Tip and RX on Ring fits perfectly.

== Killswitch configuration ==

[[File:PinePhone Kill Interruptors de Maquinari del PinePhone 4529.jpg|320px|thumb|right|Detail of DIP switch]]

The PinePhone features six switches that can be used to configure its hardware. They are numbered 1-6, with switch 1 located nearest to the modem. Their "on" position is toward the top of the phone.

{| class="wikitable"
|-
! Number
! Name
! Explanation
! Description
|-
| 1
| Modem
| Pulls Q1501 gate up (FET killing modem power)
| "On" enables 2G/3G/4G communication and GNSS hardware, "off" disables it.
|-
| 2
| WiFi / Bluetooth
| Pulls up CHIP_EN
| "On" enables WiFi and Bluetooth communication hardware, "off" disables it.
|-
| 3
| Microphone
| Breaks microphone bias voltage from the SoC
| "On" enables audio input from on-board microphones (not 3.5mm jack), "off" disables it.
|-
| 4
| Rear camera
| Pulls up PWDN on OV5640
| "On" enables the rear camera, "off" disables it.
|-
| 5
| Front camera
| Pulls up PWDN on GC2145
| "On" enables the front camera, "off" disables it.
|-
| 6
| Headphone
| Pulls up IN2 on analog switch BCT4717ETB
| "On" enables audio input and output via the 3.5mm audio jack, "off" switches the jack to hardware UART mode.
|}

== Camera ==

The PinePhone has two cameras, OmniVision OV5640 with 5MP (up to 2592 x 1944 pixels) as rear camera and GalaxyCore GC2145 with 2MP (up to 1600 x 1200 pixels) as front camera.

[[File:Rose.jpg|400px|thumb|none|Example picture taken on the PinePhone's rear camera by Martijn Braam using his app ''Megapixels''.]]

Further details regarding the camera and the Megapixels camera app can be found on [https://blog.brixit.nl/tag/phones/ Martijn's blog].

== Battery ==

{{Hint|The EG25 modem and RTL8723CS WiFi/bluetooth do not work without battery power, even if you are supplying enough power to the PinePhone with USB-C.}}

The phone ships with a plastic sticker between the battery and the phone. You need to open the back cover (gently), then remove the battery and finally remove the sticker and check that the pins aren't bent. This is to protect the device from turning on during shipping.

The [https://files.pine64.org/doc/datasheet/pinephone/PinePhone%20QZ01%20Battery%20Specification.pdf supplied battery] is [https://forum.pine64.org/showthread.php?tid=8120&pid=53307#pid53307 meant to be] compatible with Samsung part number EB-BJ700BBC / BBE / CBE from the 2015 J7 phone.
* The extended life aftermarket BBU does fit, although it is a tight fit.
* There is [https://forum.pine64.org/showthread.php?tid=8563&pid=55053#pid55053 a report] that the EB-BJ700CBE isn't quite the same size, causing the back not to fit the BraveHeart Edition properly.

The battery terminals, in order from nearest the edge to nearest the middle, are:

# +ve
# thermistor
# -ve
# not connected

The battery includes a protection circuit that isolates it in a number of fault conditions, including if it is discharged too far. The fully discharged battery [https://forum.pine64.org/showthread.php?tid=8563&pid=55377#pid55377 can be recharged] by connecting the phone to a charger. Once it has charged sufficiently you will be able to boot the phone.

If your battery is hard to remove from the phone, try loosening the screws around it. Possibly cutting up a piece of plastic and sliding it under the battery as a pull tab can work too.

<gallery mode="packed", heights=300px>
Image:PinePhone battery1.png|Photo of Brave Heart case from OSAKANA TARO on Twitter
Image:PinePhone battery3.jpeg|Photo of Brave Heart battery sticker from OSAKANA TARO on Twitter
</gallery>

== Modem and carrier support ==
=== APN settings ===

The APN setting is only required for a public Internet connection ("data") on the phone. For tested APN settings and how to apply them see [[PinePhone APN Settings]].

=== Carrier support ===
The page [[PinePhone Carrier Support]] contains information about the frequency support of different carriers and hints on setting up cellular network connectivity.

=== Documents ===

Detailed information about the modem can be found on the [https://xnux.eu/devices/feature/modem-pp.html#toc-modem-on-pinephone page of the developer megi], including reverse-engineered parts of the firmware and its functions. There is also a document about using the modem from January 18th 2020 by megi [https://megous.com/dl/tmp/modem.txt here]. A script at the end of the document showcases a way to poweroff the modem before powering off the phone, which is integrated into most of the available OSes.

=== Firmware modifications ===

See [[PineModems]] for more information regarding modem bootloader unlocking, building a custom modem firmware and modem recovery.

=== Voice mail ===

Some phone operating systems may not have support for accessing your voicemail by holding down the 1 key. If you are in Canada and using rogers or a rogers associated carrier (such as ''Chatr''), you can access your voice mail by calling an external number, see: https://www.howardforums.com/showthread.php/913346-Rogers-GSM-Voicemail-Retrieval-Numbers

In America, AT&T also has support for accessing your voicemail via an external phone number: https://www.att.com/support/article/wireless/KM1009101/

== Operating Systems ==

The PinePhone will automatically boot from microSD if a bootable card is inserted. Although it is technically possible to use any ARM distribution (because the PinePhone uses the mainline kernel), there are a few that are designed specifically for mobile use on devices like the PinePhone.

=== Software releases ===

The [[PinePhone Software Releases]] page has a complete list of currently supported phone-optimized Operating System images that work with the PinePhone as well as other related software information. As soon as more patches get mainlined and distributions ship with the updated kernel, they will also be able to run unmodified on the device.

=== Installation instructions ===

For instructions on how to install the operating systems to the eMMC or SD card see [[PinePhone Installation Instructions]].

=== Flashing eMMC using Jumpdrive ===

[[File:jumpdrive.jpg|400px|thumb|right|Jumpdrive running on the PinePhone]]
The internal eMMC flash storage can be flashed using the Jumpdrive utility by Danct12 and Martijn from postmarketOS.
This utility boots from micro SD and exposes the internal eMMC flash storage when the PinePhone is connected to a computer.
The process of flashing an OS to the exposed and mounted eMMC is identical to that of any other storage medium - e.g. a SD card. You can use the 'DD' command or a utility such as Etcher or Gnome Disks, etc.

Latest Jumpdrive can be found [https://github.com/dreemurrs-embedded/Jumpdrive/releases/ here].

==== Detailed usage instructions ====

# Download the Jumpdrive image
# Flash the Jumpdrive image to a micro SD card
# Boot the PinePhone from the Jumpdrive micro SD card
# Connect the PinePhone to your computer using USB-A -> USB-C cable
# Flash the exposed PinePhone drive (e.g. /dev/mm..., check for the right device in dmesg, GNOME disks, or similar, and make sure it's unmounted) with your chosen OS image
# Once the flashing process is complete, disconnect the PinePhone from your PC, power it down and remove the Jumpdrive SD card
# The process is now finished, and you can boot from eMMC

Jumpdrive also acts as a rescue image in case if you messed up your installation. To do so, you can telnet to '''172.16.42.1''', mount rootfs and fix it!

==== Resize file system ====

If you flash a 4GB image distribution (such as phosh+debian) to your eMMC, your eMMC will only have a 3.7GB partition on it. To use the entire 14.7GB on the eMMC, run the following commands:

# sudo cfdisk /dev/sdX
# Change to [Resize] in the ncurses program, resize the 3.7GB partition to 14.7GB, and [Write]
# sudo resize2fs /dev/sdXY

Replace X with your drive's name. Replace Y with the partition you resized in cfdisk.

==== Feedback ====

If you've found an issue or want to improve the tool consider these sites:

* Issues: https://github.com/dreemurrs-embedded/Jumpdrive/issues
* Pull Requests: https://github.com/dreemurrs-embedded/Jumpdrive/pulls

== Frequently asked questions ==

For a list of frequently asked questions (including information regarding the shipping) see [[PinePhone FAQ]].

== Press ==

For an overview about media of the PinePhone you can use for the news, blogs, or similar see [[PinePhone Press]].

== PinePhone board information, schematics and certifications ==
* PinePhone mainboard schematic:
** [https://files.pine64.org/doc/PinePhone/PinePhone%20v1.2b%20Released%20Schematic.pdf PinePhone mainboard Released Schematic ver 1.2b]
** [https://files.pine64.org/doc/PinePhone/PinePhone%20v1.2a%20Released%20Schematic.pdf PinePhone mainboard Released Schematic ver 1.2a]
** [https://files.pine64.org/doc/PinePhone/PinePhone%20v1.2%20Released%20Schematic.pdf PinePhone mainboard Released Schematic ver 1.2]
** [[PinePhone_v1.2|PinePhone schematic ver 1.2 change list]]
** [https://files.pine64.org/doc/PinePhone/PinePhone%20Schematic%20v1.1%2020191031.pdf "Braveheart" PinePhone mainboard Schematic ver 1.1]
** [https://files.pine64.org/doc/PinePhone/PinePhone%20mainboard%20top%20placement%20v1.1%2020191031.pdf "Braveheart" PinePhone mainboard component top placement drawing ver 1.1]
** [https://files.pine64.org/doc/PinePhone/PinePhone%20mainboard%20bottom%20placement%20v1.1%2020191031.pdf "Braveheart" PinePhone mainboard component bottom placement drawing ver 1.1]
* PinePhone USB-C small board schematic:
** [https://files.pine64.org/doc/PinePhone/PinePhone%20USB-C%20small%20board%20schematic%20v1.0%2020190730.pdf PinePhone USB-C small board Schematic ver 1.0]
** [https://files.pine64.org/doc/PinePhone/PinePhone%20USB-C%20small%20board%20top%20placement%20v1.0%2020190730.pdf PinePhone USB-C small board component top placement drawing ver 1.0]
** [https://files.pine64.org/doc/PinePhone/PinePhone%20USB-C%20small%20board%20bottom%20placement%20v1.0%2020190730.pdf PinePhone USB-C small board component bottom placement drawing ver 1.0]
* PinePhone certifications:
** [https://files.pine64.org/doc/cert/PinePhone%20FCC%20SDOC%20Certificate-S19112602605001.pdf PinePhone FCC Certificate]
** [https://fcc.report/FCC-ID/2AWAG-PINEPHONE RF Exposure SAR Information from FCC ID site]
** [https://files.pine64.org/doc/cert/PinePhone%20CE%20RED%20Certificate-S19112602602.pdf PinePhone CE RED Certificate]
** [https://files.pine64.org/doc/cert/PinePhone%20ROHS%20Report.pdf PinePhone ROHS Report]
** PinePhone's GSMA TAC (Type Allocation Code) is 86769804

== Datasheets for components and peripherals ==

* Allwinner A64 SoC information:
** [https://files.pine64.org/doc/datasheet/pine64/A64%20brief%20v1.0%2020150323.pdf Allwinner A64 SoC brief introduction]
** [https://files.pine64.org/doc/datasheet/pine64/A64_Datasheet_V1.1.pdf Allwinner A64 SoC Data Sheet V1.1 (Official Released Version)]
** [https://files.pine64.org/doc/datasheet/pine64/Allwinner_A64_User_Manual_V1.0.pdf Allwinner A64 SoC User Manual V1.0 (Official Release Version)]

* X-Powers AXP803 PMU (Power Management Unit) information:
** [https://files.pine64.org/doc/datasheet/pine64/AXP803_Datasheet_V1.0.pdf AXP803 PMIC datasheet]

* LPDDR3 (178 Balls) SDRAM:
** [https://files.pine64.org/doc/datasheet/pinephone/ATL3A1632H12A_mobile_lpddr3_11x11.5_v1.0_1600.pdf Artmem LPDDR3 datasheet]

* eMMC information:
** [https://files.pine64.org/doc/datasheet/pinephone/Kimtigo_fbga153_16_32_64_eMMC_datasheet_v1.3.pdf Kimtigo eMMC datasheet]

* CMOS camera module information:
** [https://files.pine64.org/doc/datasheet/pinephone/QZ01-rear-2019-0717(HW)%20Model.pdf PinePhone 5M Pixel Real CMOS Image Sensor Module]
** [https://files.pine64.org/doc/datasheet/pinephone/OV5640_datasheet.pdf OV5640 5MP CMOS Image Sensor SoC for Rear Module datasheet]
** [https://files.pine64.org/doc/datasheet/pinephone/QZ01-front-2019-0717(HW)%20Model.pdf PinePhone 2M Pixel Front CMOS Image Sensor Module]
** [https://files.pine64.org/doc/datasheet/pinephone/GC2145%20CSP%20DataSheet%20release%20V1.0_20131201.pdf GC2145 2MP CMOS Image Sensor SoC for Front Module datasheet]

* LCD touch screen panel information:
** [https://files.pine64.org/doc/datasheet/pinephone/PinePhone%20LCD-QZ01.pdf 5.99" 1440x720 LCD IPS Panel specification]
** [https://files.pine64.org/doc/datasheet/pinephone/ST7703_DS_v01_20160128.pdf ST7703 LCD Controller datasheet]
** [https://files.pine64.org/doc/datasheet/pinephone/GT917S-Datasheet.pdf GOODiX GT917S Capacitive Touch Controller datasheet]

* Lithium battery information:
** [https://files.pine64.org/doc/datasheet/pinephone/PinePhone%20QZ01%20Battery%20Specification.pdf PinePhone Lithium Battery specification]
** [https://files.pine64.org/doc/datasheet/pinephone/PinePhone%20QZ01%20Battery%20ZCV%20Curve%20Chart.xlsx PinePhone Lithium Battery ZCV curve chart]

* WiFi/BT module information:
** [https://files.pine64.org/doc/datasheet/pine64/RTL8723BS.pdf RTL8723BS/RTL8723CS specification]

* LTE module information:
** [https://www.quectel.com/UploadFile/Product/Quectel_EG25-G_LTE_Standard_Specification_V1.2.pdf Quectel EG25-G LTE Module specification v1.2]
** [[Media:Quectel EC25EC21 AT Commands Manual V1.2.pdf|EC25&EC21 AT Commands Manual]]
** [https://www.quectel.com/UploadImage/Downlad/Quectel_EC2x&EG25-G&EG9x&EM05_FILE_AT_Commands_Manual_V1.0.pdf Quectel EC2x EG25-G EG9x EM05 FILE AT Commands Manual v1.0]
** [https://sixfab.com/wp-content/uploads/2018/09/Quectel_EC25EC21_GNSS_AT_Commands_Manual_V1.1.pdf Quectel EC25 EC21 GNSS AT Commands Manual v1.1]

* Sensors:
** [https://www.st.com/en/mems-and-sensors/lis3mdl.html ST LIS3MDL 3-axis Magnetomater Datasheet]
** [https://www.invensense.com/products/motion-tracking/6-axis/mpu-6050/ InvenSense MPU-6050 Six-Axis (Gyro + Accelerometer) MEMS datasheet]
** [https://www.sensortek.com.tw/en/product/Proximity_Sensor_with_ALS.html SensorTek STK3335 Ambient Light Sensor and Proximity Sensor]

* Digital video to USB-C bridge:
** [https://www.analogix.com/en/system/files/AA-002281-PB-6-ANX7688_Product_Brief.pdf ANX7688 product brief]

* Case information:
** [https://files.pine64.org/doc/datasheet/pinephone/PinePhone%20Exploded%20Diagram%20ver%201.0.pdf PinePhone case exploded diagram]
** [https://files.pine64.org/doc/datasheet/pinephone/PinePhone%20Back%20Cover.stp PinePhone back cover 3D file]

* Other components:
** See links in the [[PinePhone_component_list|Component List]]

== Developer works ==
=== Megous ===

* [https://xnux.eu/howtos/pine64-pinephone-getting-started.html Getting start with PinePhone Hardware]
* [https://xnux.eu/devices/pine64-pinephone.html State of development progress]
* [https://xnux.eu/news.html PinePhone Technical News and Update, also applies to other Allwinner devices including PINE A64 SBC]
* [https://xnux.eu/contribute.html Contributions to the kernel development]

== External links ==
* [https://pine64.com/product-category/pinephone/ The PinePhone on the official Pine store]
* [https://pine64.com/product-category/smarphone-spare-parts/ PinePhone spare parts on the official Pine store]
* [https://pine64.com/product-category/smartphone-accessories/ PinePhone accessories on the official Pine store]

[[Category:PinePhone]] [[Category:Allwinner A64]]

PinePhone

2020-12-05T22:32:02Z

Zebulon Walton:

The PinePhone is a smartphone created by Pine64, capable of running mainline Linux and supported by many partner projects. The BraveHeart Edition was the first publicly-available version of the phone, though it came without a fully functional OS (factory test image) and was geared specifically towards tinkerers and hackers. Its successor is the Community Edition, the first Community Edition started to ship in June 2020. The phone will be available for at least five years.

== First time installation ==

{{Hint|The default PIN for the Manjaro Community Edition is '''123456'''.}}

[[File:PinePhone-3.jpg|400px|thumb|right|PinePhone is capable of running a multitude of different Linux mobile OSes]]

[[File:Pinephone_rendering_blank.png|400px|thumb|right|Rendering of the back and front of PinePhone]]

From the factory the battery has a sticker on it that isolates the battery from the phone. The battery '''will not''' charge until this is removed.

[[File:Pinephone_warning.png|none|left|400px]]

After unboxing remove the back panel using the notch in the corner of the back panel. Then remove the battery and peel off the clear plastic sticker below it that isolates the charging contact. Then replace the battery, see [[PinePhone#Battery|Battery]] for more information.

The SIM card has to be placed in the lower slot, while the microSD has to be placed in the upper slot, as pictured here:

[[File:Pinephone_backside.png|none|left|400px]]

== Specifications ==

'''Dimensions:''' 160.5 x 76.6 x 9.2mm 
'''Weight:''' Between 180-200 grams 
'''SIM Card:''' Micro-SIM 
'''Display:'''
: '''Size:''' 5.95 inches (151mm) diagonal
: '''Type:''' HD IPS capacitive touchscreen, 16M colors
: '''Resolution:''' 1440x720, 18:9 ratio 
'''System on Chip:''' [https://linux-sunxi.org/A64 Allwinner A64] 
'''RAM:''' 2GB or 3GB LPDDR3 SDRAM 
'''Internal Storage:''' 16GB or 32GB eMMC, extendable up to 2TB via microSD, supports SDHC and SDXC 
'''Back Camera:''' Single 5MP, 1/4", LED Flash 
'''Selfie Camera:''' Single 2MP, f/2.8, 1/5" 
'''Sound:''' Loudspeaker, 3.5mm jack & mic (jack doubles as hardware UART if killswitch 6 is deactivated) 
'''Communication: G25-G'''
: '''LTE:''' B1, B2, B3, B4, B5, B7, B8, B12, B13, B18, B19, B20, B25, B26, B28, B38, B39, B40, B41
: '''WCDMA:''' B1, B2, B4, B5, B6, B8, B19
: '''GSM:''' 850, 900, 1800, 1900 (MHz)
: '''WLAN:''' Wi-Fi 802.11 b/g/n, single-band, hotspot
: '''Bluetooth:''' 4.0, A2DP
: '''GNSS:''' GPS/GLONASS/BeiDou/Galileo/QZSS, with A-GPS
'''Sensors:''' Accelerometer, gyro, proximity, ambient light, compass 
'''Killswitches:''' Modem, WiFi & Bluetooth, Microphone, Cameras 
'''Battery:''' Lithium-ion, rated capacity 2800mAh (10.64Wh), typical capacity 3000mAh (11.40Wh) (nominally replaceable with any Samsung J7 form-factor battery) 
'''I/O:''' USB Type-C, USB Host, DisplayPort Alternate Mode output, 15W 5V 3A Quick Charge, follows USB PD specification

== Components ==
{| class="wikitable"
! Component
! Model
|-
| Touchscreen
| Goodix GT917S
|-
| Rear camera
| OmniVision OV5640
|-
| Camera flash
| SGMICRO SGM3140
|-
| Front camera
| GalaxyCore GC2145
|-
| LCD
| Xingbangda XBD599
|-
| WiFi
| Realtek RTL8723CS
|-
| Bluetooth
| Realtek RTL8723CS
|-
| Modem
| Quectel EG25-G
|-
| GNSS/GPS
| Quectel EG25-G
|-
| Magnetometer
| ST LIS3MDL
|-
| Ambient light / Proximity
| SensorTek STK3335
|-
| Sixaxis
| InvenSense MPU-6050
|-
| Vibration motor
| Unknown model
|-
| Notification LED
| LED0603RGB
|-
| Volume buttons
| Buttons connected to the KEYADC
|-
| Power button
| X-Powers AXP803
|-
| Battery fuel gauge
| X-Powers AXP803
|}

See the [[PinePhone_component_list|PinePhone Component List]].

== Hardware revisions ==

# [[Project Anakin]]
# [[Project Don't be evil|"Project Don't Be Evil" devkit]]
# [[PinePhone v1.0 - Dev|PinePhone v1.0 - Developer batch]]
# [[PinePhone v1.1 - Braveheart]]
# [[PinePhone v1.2‎]] - Ubports Community Edition
# [[PinePhone v1.2a]] - postmarketOS Community Edition
# [[PinePhone v1.2b]] - Manjaro Community Edition

== Swapping in a new mainboard revision ==

The mainboard can be replaced, for example for upgrading to a newer hardware revision or if it is faulty. The replacement board does not have an OS preinstalled, to test if everything is working after swapping the mainboard a flashed SD card is required. The mainboard also comes with a non-functional firmware on the ANX chip, a newer firmware version has to be flashed as explained below to get certain USB functionality to work.

=== Replacing the mainboard ===

Prior to replacing your PinePhone’s mainboard please read the steps outlined in bullet points below and watch the attached video.

# You’ll need a small Phillip’s screwdriver and a prying tool to swap out the PinePhone’s mainboard.
# Remove the PinePhone’s back cover. See your quick start guide for details.
# Remove the battery as well as any inserted SD and SIM cards.
# Unscrew all 15 Phillip’s head screws around the midframe of the phone.
# Gently pry up the midframe using a guitar pick or credit card corner. It is easiest to separate the midframe at one of the bottom edges. Work your way around all the sides of the phone until the midframe separates from the phone’s body.
# Detach all ribbon cables and “Lego” connectors. List of things to detach: 1) two “Lego” connects at the bottom of the mainboard. 2) u.FL antenna connect and touchscreen digitizer on PCD left side. 3) LCD ribbon cable top of mainboard, next to audio/ UART jack.
# Pry the mainboard up gently from the left-hand side.
# Remove front and main cameras and reset them into the new mainboard.
# Check that the rubber proximity sensor housing is in the chassis, not stuck to the removed mainboard.
# Place the new mainboard in the chassis, hooking in on the plastic tabs on left side and pressing down firmly on opposite side, and follow the steps (7-2) in reverse. When reattaching the midframe take care that no cables are out of place or trapped, as they may be damaged when tightening screws.

After swapping the mainboard the phone won't boot as there is no OS on the replacement board's eMMC preinstalled. To boot an OS insert a flashed SD card.

A video tutorial can be found here:
[[File:Pinephone_martijn_pcb_replacement.png|thumb|none|600px|link=https://www.youtube.com/watch?v=5GbMoZ_zuZs|Watch Martijn Braam's video tutorial here: https://www.youtube.com/watch?v=5GbMoZ_zuZs. Alternatively user bridadan uploaded a video tutorial of the swap procedure including camera swap and proximity sensor housing here: https://www.youtube.com/watch?v=J3AJEF7akkw.]]

=== Flashing the ANX firmware ===

After swapping the mainboard the ANX chip has to be flashed for full USB functionality.

Download the latest ANX firmware image on the phone:

wget https://xff.cz/git/linux-firmware/plain/anx7688-fw.bin

Execute as root ("sudo su") on the phone:

cp anx7688-fw.bin /lib/firmware/
echo 1 > /sys/class/typec/port0/device/flash_eeprom

== Replacing the screen ==

Before attempting to replace the screen be sure to review the section [[Replacing the mainboard]] since that will get you most of the way there. Be aware that the replacement screen is actually the entire front frame of the phone and there are components that will need to be swapped from your old screen.

* Make sure you have a precision screwdriver set that has the correct size Philips tip. The screws are very small and the heads can easily be stripped if the screwdriver is not correct - if you feel your screwdriver slipping, stop what you are doing and try one that is a better fit. A magnetized screwdriver will help in not losing screws, as will a magnetic parts holder to keep them in while working.

* There are a number of components and cables as well as the insulator sheet under the battery that are glued in place. A hair dryer will loosen the glue and make them much easier to remove. You may want to order extra cables along with the screen just in case.

* The vibrator motor, which is part of the USB-C board assembly and glued into place, will come apart easily and be damaged if you pry it up in the wrong place. Make sure you pry from underneath the complete part, not midway on its housing. The ribbon cable attaching this to the USB-C board is small, thin, and fragile so be careful with that as well.

* The new screen comes with new side switches and insulator sheet but there are a number of parts that need to be transferred from the old screen, like the thin coax cable running up the side, the phone ear speaker, proximity sensor gasket, and a gold-colored mesh glued in place that needs to be transferred to a flexible circuit included on the new screen. If you don't swap over the proximity sensor rubber gasket the screen will immediately turn off after logging in. Be careful when routing the coax cable that it goes around the screw holes or you may drive a screw right through the cable.

Take your time, use the right tools, be careful and you should be rewarded with success.

== Hardware accessory ==

=== PinePhone hardware accessory compatibility ===
See [[PinePhone Hardware Accessory Compatibility]] for a list of devices working with the PinePhone (depending on their OS support).

=== USB-C connector ===

The USB-C can be used to power the device, and offers USB2 host and OTG possibilities, and also can make use of the USB-C capability to integrate HDMI signals. Some USB-C hubs are available that offer power throughput, USB connection, HDMI port and Ethernet connection. The driver that would make this connection available is not supported at this time.

=== Pogo pins ===

The PinePhone has 6 pogo pins on the back allowing for custom hardware extensions such as wireless charging, an IR blaster, a keyboard extension or extended battery case. The pogo pins provide access to an interrupt line, power input to charge the battery, power source and an I2C interface.

[[File:Pinephone pogo.png|none|400px]]

{| class="wikitable"
| Interrupt
| SDA
| SCL
|-
| 5V / VBUS
| VBAT
| GND
|}

The VBUS pin is powered by USB and is 5V. The second power pin is VBAT, which connects to the battery voltage. The I2C and interrupt lines have pull-ups on the phone side. The I2C lines are pulled up to 3V3 by the phone.

For a breakout board see [https://github.com/SMR404/PinephonePogoBreakout here]. For an example project see Martijn's blog post [https://blog.brixit.nl/making-a-backcover-extension-for-the-pinephone/ "Making a backcover extension for the PinePhone"].

=== Back cover ===
A step file for the back cover for creating custom cases is freely available [https://files.pine64.org/doc/PinePhone/PinePhone%20Back%20Cover%20ver%200.5.stp here].

=== Serial console ===

The PinePhone has a serial port in the headphone connector, it's activated by the 6th contact on the dipswitch. If the switch is set to "on", the headphone connector is in audio mode, if it is set to "off" it's in UART mode. The UART serial connection can also be used for communication with other devices from the PinePhone.

The UART is 115200n8.

The pinout for the serial connector is:

* Tip: RX
* Ring: TX
* Sleeve: GND

[[File:PinePhone_Serial_Cable.png|none|400px]]

You can buy a serial debug cable from the [https://pine64.com/product/pinebook-pinephone-pinetab-serial-console/ Pine64 Store]. The store cable uses a 4 ring plug, as seen in the [https://files.pine64.org/doc/pinebook/guide/Pinebook_Earphone_Serial_Console_Developer_Guide.pdf here], but a 3 ring plug works just as well. The cable uses a CH340 chipset based serial to USB converter, but any 3.3v serial connection can be used. Because it is a "host"/DTE it means that you need a ''cross modem cable'' ([https://en.wikipedia.org/wiki/Null_modem Null Modem]) with TX on Tip to be connected to RX. A cable like e.g. [https://www.ftdichip.com/Products/Cables/USBTTLSerial.htm FTDI TTL-232R-3V3-AJ] which has TX on Tip and RX on Ring fits perfectly.

== Killswitch configuration ==

[[File:PinePhone Kill Interruptors de Maquinari del PinePhone 4529.jpg|320px|thumb|right|Detail of DIP switch]]

The PinePhone features six switches that can be used to configure its hardware. They are numbered 1-6, with switch 1 located nearest to the modem. Their "on" position is toward the top of the phone.

{| class="wikitable"
|-
! Number
! Name
! Explanation
! Description
|-
| 1
| Modem
| Pulls Q1501 gate up (FET killing modem power)
| "On" enables 2G/3G/4G communication and GNSS hardware, "off" disables it.
|-
| 2
| WiFi / Bluetooth
| Pulls up CHIP_EN
| "On" enables WiFi and Bluetooth communication hardware, "off" disables it.
|-
| 3
| Microphone
| Breaks microphone bias voltage from the SoC
| "On" enables audio input from on-board microphones (not 3.5mm jack), "off" disables it.
|-
| 4
| Rear camera
| Pulls up PWDN on OV5640
| "On" enables the rear camera, "off" disables it.
|-
| 5
| Front camera
| Pulls up PWDN on GC2145
| "On" enables the front camera, "off" disables it.
|-
| 6
| Headphone
| Pulls up IN2 on analog switch BCT4717ETB
| "On" enables audio input and output via the 3.5mm audio jack, "off" switches the jack to hardware UART mode.
|}

== Camera ==

The PinePhone has two cameras, OmniVision OV5640 with 5MP (up to 2592 x 1944 pixels) as rear camera and GalaxyCore GC2145 with 2MP (up to 1600 x 1200 pixels) as front camera.

[[File:Rose.jpg|400px|thumb|none|Example picture taken on the PinePhone's rear camera by Martijn Braam using his app ''Megapixels''.]]

Further details regarding the camera and the Megapixels camera app can be found on [https://blog.brixit.nl/tag/phones/ Martijn's blog].

== Battery ==

{{Hint|The EG25 modem and RTL8723CS WiFi/bluetooth do not work without battery power, even if you are supplying enough power to the PinePhone with USB-C.}}

The phone ships with a plastic sticker between the battery and the phone. You need to open the back cover (gently), then remove the battery and finally remove the sticker and check that the pins aren't bent. This is to protect the device from turning on during shipping.

The [https://files.pine64.org/doc/datasheet/pinephone/PinePhone%20QZ01%20Battery%20Specification.pdf supplied battery] is [https://forum.pine64.org/showthread.php?tid=8120&pid=53307#pid53307 meant to be] compatible with Samsung part number EB-BJ700BBC / BBE / CBE from the 2015 J7 phone.
* The extended life aftermarket BBU does fit, although it is a tight fit.
* There is [https://forum.pine64.org/showthread.php?tid=8563&pid=55053#pid55053 a report] that the EB-BJ700CBE isn't quite the same size, causing the back not to fit the BraveHeart Edition properly.

The battery terminals, in order from nearest the edge to nearest the middle, are:

# +ve
# thermistor
# -ve
# not connected

The battery includes a protection circuit that isolates it in a number of fault conditions, including if it is discharged too far. The fully discharged battery [https://forum.pine64.org/showthread.php?tid=8563&pid=55377#pid55377 can be recharged] by connecting the phone to a charger. Once it has charged sufficiently you will be able to boot the phone.

If your battery is hard to remove from the phone, try loosening the screws around it. Possibly cutting up a piece of plastic and sliding it under the battery as a pull tab can work too.

<gallery mode="packed", heights=300px>
Image:PinePhone battery1.png|Photo of Brave Heart case from OSAKANA TARO on Twitter
Image:PinePhone battery3.jpeg|Photo of Brave Heart battery sticker from OSAKANA TARO on Twitter
</gallery>

== Modem and carrier support ==
=== APN settings ===

The APN setting is only required for a public Internet connection ("data") on the phone. For tested APN settings and how to apply them see [[PinePhone APN Settings]].

=== Carrier support ===
The page [[PinePhone Carrier Support]] contains information about the frequency support of different carriers and hints on setting up cellular network connectivity.

=== Documents ===

Detailed information about the modem can be found on the [https://xnux.eu/devices/feature/modem-pp.html#toc-modem-on-pinephone page of the developer megi], including reverse-engineered parts of the firmware and its functions. There is also a document about using the modem from January 18th 2020 by megi [https://megous.com/dl/tmp/modem.txt here]. A script at the end of the document showcases a way to poweroff the modem before powering off the phone, which is integrated into most of the available OSes.

=== Firmware modifications ===

See [[PineModems]] for more information regarding modem bootloader unlocking, building a custom modem firmware and modem recovery.

=== Voice mail ===

Some phone operating systems may not have support for accessing your voicemail by holding down the 1 key. If you are in Canada and using rogers or a rogers associated carrier (such as ''Chatr''), you can access your voice mail by calling an external number, see: https://www.howardforums.com/showthread.php/913346-Rogers-GSM-Voicemail-Retrieval-Numbers

In America, AT&T also has support for accessing your voicemail via an external phone number: https://www.att.com/support/article/wireless/KM1009101/

== Operating Systems ==

The PinePhone will automatically boot from microSD if a bootable card is inserted. Although it is technically possible to use any ARM distribution (because the PinePhone uses the mainline kernel), there are a few that are designed specifically for mobile use on devices like the PinePhone.

=== Software releases ===

The [[PinePhone Software Releases]] page has a complete list of currently supported phone-optimized Operating System images that work with the PinePhone as well as other related software information. As soon as more patches get mainlined and distributions ship with the updated kernel, they will also be able to run unmodified on the device.

=== Installation instructions ===

For instructions on how to install the operating systems to the eMMC or SD card see [[PinePhone Installation Instructions]].

=== Flashing eMMC using Jumpdrive ===

[[File:jumpdrive.jpg|400px|thumb|right|Jumpdrive running on the PinePhone]]
The internal eMMC flash storage can be flashed using the Jumpdrive utility by Danct12 and Martijn from postmarketOS.
This utility boots from micro SD and exposes the internal eMMC flash storage when the PinePhone is connected to a computer.
The process of flashing an OS to the exposed and mounted eMMC is identical to that of any other storage medium - e.g. a SD card. You can use the 'DD' command or a utility such as Etcher or Gnome Disks, etc.

Latest Jumpdrive can be found [https://github.com/dreemurrs-embedded/Jumpdrive/releases/ here].

==== Detailed usage instructions ====

# Download the Jumpdrive image
# Flash the Jumpdrive image to a micro SD card
# Boot the PinePhone from the Jumpdrive micro SD card
# Connect the PinePhone to your computer using USB-A -> USB-C cable
# Flash the exposed PinePhone drive (e.g. /dev/mm..., check for the right device in dmesg, GNOME disks, or similar, and make sure it's unmounted) with your chosen OS image
# Once the flashing process is complete, disconnect the PinePhone from your PC, power it down and remove the Jumpdrive SD card
# The process is now finished, and you can boot from eMMC

Jumpdrive also acts as a rescue image in case if you messed up your installation. To do so, you can telnet to '''172.16.42.1''', mount rootfs and fix it!

==== Resize file system ====

If you flash a 4GB image distribution (such as phosh+debian) to your eMMC, your eMMC will only have a 3.7GB partition on it. To use the entire 14.7GB on the eMMC, run the following commands:

# sudo cfdisk /dev/sdX
# Change to [Resize] in the ncurses program, resize the 3.7GB partition to 14.7GB, and [Write]
# sudo resize2fs /dev/sdXY

Replace X with your drive's name. Replace Y with the partition you resized in cfdisk.

==== Feedback ====

If you've found an issue or want to improve the tool consider these sites:

* Issues: https://github.com/dreemurrs-embedded/Jumpdrive/issues
* Pull Requests: https://github.com/dreemurrs-embedded/Jumpdrive/pulls

== Frequently asked questions ==

For a list of frequently asked questions (including information regarding the shipping) see [[PinePhone FAQ]].

== Press ==

For an overview about media of the PinePhone you can use for the news, blogs, or similar see [[PinePhone Press]].

== PinePhone board information, schematics and certifications ==
* PinePhone mainboard schematic:
** [https://files.pine64.org/doc/PinePhone/PinePhone%20v1.2b%20Released%20Schematic.pdf PinePhone mainboard Released Schematic ver 1.2b]
** [https://files.pine64.org/doc/PinePhone/PinePhone%20v1.2a%20Released%20Schematic.pdf PinePhone mainboard Released Schematic ver 1.2a]
** [https://files.pine64.org/doc/PinePhone/PinePhone%20v1.2%20Released%20Schematic.pdf PinePhone mainboard Released Schematic ver 1.2]
** [[PinePhone_v1.2|PinePhone schematic ver 1.2 change list]]
** [https://files.pine64.org/doc/PinePhone/PinePhone%20Schematic%20v1.1%2020191031.pdf "Braveheart" PinePhone mainboard Schematic ver 1.1]
** [https://files.pine64.org/doc/PinePhone/PinePhone%20mainboard%20top%20placement%20v1.1%2020191031.pdf "Braveheart" PinePhone mainboard component top placement drawing ver 1.1]
** [https://files.pine64.org/doc/PinePhone/PinePhone%20mainboard%20bottom%20placement%20v1.1%2020191031.pdf "Braveheart" PinePhone mainboard component bottom placement drawing ver 1.1]
* PinePhone USB-C small board schematic:
** [https://files.pine64.org/doc/PinePhone/PinePhone%20USB-C%20small%20board%20schematic%20v1.0%2020190730.pdf PinePhone USB-C small board Schematic ver 1.0]
** [https://files.pine64.org/doc/PinePhone/PinePhone%20USB-C%20small%20board%20top%20placement%20v1.0%2020190730.pdf PinePhone USB-C small board component top placement drawing ver 1.0]
** [https://files.pine64.org/doc/PinePhone/PinePhone%20USB-C%20small%20board%20bottom%20placement%20v1.0%2020190730.pdf PinePhone USB-C small board component bottom placement drawing ver 1.0]
* PinePhone certifications:
** [https://files.pine64.org/doc/cert/PinePhone%20FCC%20SDOC%20Certificate-S19112602605001.pdf PinePhone FCC Certificate]
** [https://fcc.report/FCC-ID/2AWAG-PINEPHONE RF Exposure SAR Information from FCC ID site]
** [https://files.pine64.org/doc/cert/PinePhone%20CE%20RED%20Certificate-S19112602602.pdf PinePhone CE RED Certificate]
** [https://files.pine64.org/doc/cert/PinePhone%20ROHS%20Report.pdf PinePhone ROHS Report]
** PinePhone's GSMA TAC (Type Allocation Code) is 86769804

== Datasheets for components and peripherals ==

* Allwinner A64 SoC information:
** [https://files.pine64.org/doc/datasheet/pine64/A64%20brief%20v1.0%2020150323.pdf Allwinner A64 SoC brief introduction]
** [https://files.pine64.org/doc/datasheet/pine64/A64_Datasheet_V1.1.pdf Allwinner A64 SoC Data Sheet V1.1 (Official Released Version)]
** [https://files.pine64.org/doc/datasheet/pine64/Allwinner_A64_User_Manual_V1.0.pdf Allwinner A64 SoC User Manual V1.0 (Official Release Version)]

* X-Powers AXP803 PMU (Power Management Unit) information:
** [https://files.pine64.org/doc/datasheet/pine64/AXP803_Datasheet_V1.0.pdf AXP803 PMIC datasheet]

* LPDDR3 (178 Balls) SDRAM:
** [https://files.pine64.org/doc/datasheet/pinephone/ATL3A1632H12A_mobile_lpddr3_11x11.5_v1.0_1600.pdf Artmem LPDDR3 datasheet]

* eMMC information:
** [https://files.pine64.org/doc/datasheet/pinephone/Kimtigo_fbga153_16_32_64_eMMC_datasheet_v1.3.pdf Kimtigo eMMC datasheet]

* CMOS camera module information:
** [https://files.pine64.org/doc/datasheet/pinephone/QZ01-rear-2019-0717(HW)%20Model.pdf PinePhone 5M Pixel Real CMOS Image Sensor Module]
** [https://files.pine64.org/doc/datasheet/pinephone/OV5640_datasheet.pdf OV5640 5MP CMOS Image Sensor SoC for Rear Module datasheet]
** [https://files.pine64.org/doc/datasheet/pinephone/QZ01-front-2019-0717(HW)%20Model.pdf PinePhone 2M Pixel Front CMOS Image Sensor Module]
** [https://files.pine64.org/doc/datasheet/pinephone/GC2145%20CSP%20DataSheet%20release%20V1.0_20131201.pdf GC2145 2MP CMOS Image Sensor SoC for Front Module datasheet]

* LCD touch screen panel information:
** [https://files.pine64.org/doc/datasheet/pinephone/PinePhone%20LCD-QZ01.pdf 5.99" 1440x720 LCD IPS Panel specification]
** [https://files.pine64.org/doc/datasheet/pinephone/ST7703_DS_v01_20160128.pdf ST7703 LCD Controller datasheet]
** [https://files.pine64.org/doc/datasheet/pinephone/GT917S-Datasheet.pdf GOODiX GT917S Capacitive Touch Controller datasheet]

* Lithium battery information:
** [https://files.pine64.org/doc/datasheet/pinephone/PinePhone%20QZ01%20Battery%20Specification.pdf PinePhone Lithium Battery specification]
** [https://files.pine64.org/doc/datasheet/pinephone/PinePhone%20QZ01%20Battery%20ZCV%20Curve%20Chart.xlsx PinePhone Lithium Battery ZCV curve chart]

* WiFi/BT module information:
** [https://files.pine64.org/doc/datasheet/pine64/RTL8723BS.pdf RTL8723BS/RTL8723CS specification]

* LTE module information:
** [https://www.quectel.com/UploadFile/Product/Quectel_EG25-G_LTE_Standard_Specification_V1.2.pdf Quectel EG25-G LTE Module specification v1.2]
** [[Media:Quectel EC25EC21 AT Commands Manual V1.2.pdf|EC25&EC21 AT Commands Manual]]
** [https://www.quectel.com/UploadImage/Downlad/Quectel_EC2x&EG25-G&EG9x&EM05_FILE_AT_Commands_Manual_V1.0.pdf Quectel EC2x EG25-G EG9x EM05 FILE AT Commands Manual v1.0]
** [https://sixfab.com/wp-content/uploads/2018/09/Quectel_EC25EC21_GNSS_AT_Commands_Manual_V1.1.pdf Quectel EC25 EC21 GNSS AT Commands Manual v1.1]

* Sensors:
** [https://www.st.com/en/mems-and-sensors/lis3mdl.html ST LIS3MDL 3-axis Magnetomater Datasheet]
** [https://www.invensense.com/products/motion-tracking/6-axis/mpu-6050/ InvenSense MPU-6050 Six-Axis (Gyro + Accelerometer) MEMS datasheet]
** [https://www.sensortek.com.tw/en/product/Proximity_Sensor_with_ALS.html SensorTek STK3335 Ambient Light Sensor and Proximity Sensor]

* Digital video to USB-C bridge:
** [https://www.analogix.com/en/system/files/AA-002281-PB-6-ANX7688_Product_Brief.pdf ANX7688 product brief]

* Case information:
** [https://files.pine64.org/doc/datasheet/pinephone/PinePhone%20Exploded%20Diagram%20ver%201.0.pdf PinePhone case exploded diagram]
** [https://files.pine64.org/doc/datasheet/pinephone/PinePhone%20Back%20Cover.stp PinePhone back cover 3D file]

* Other components:
** See links in the [[PinePhone_component_list|Component List]]

== Developer works ==
=== Megous ===

* [https://xnux.eu/howtos/pine64-pinephone-getting-started.html Getting start with PinePhone Hardware]
* [https://xnux.eu/devices/pine64-pinephone.html State of development progress]
* [https://xnux.eu/news.html PinePhone Technical News and Update, also applies to other Allwinner devices including PINE A64 SBC]
* [https://xnux.eu/contribute.html Contributions to the kernel development]

== External links ==
* [https://pine64.com/product-category/pinephone/ The PinePhone on the official Pine store]
* [https://pine64.com/product-category/smarphone-spare-parts/ PinePhone spare parts on the official Pine store]
* [https://pine64.com/product-category/smartphone-accessories/ PinePhone accessories on the official Pine store]

[[Category:PinePhone]] [[Category:Allwinner A64]]

PinePhone

2020-12-05T22:26:26Z

Zebulon Walton: Added screen replacement section

The PinePhone is a smartphone created by Pine64, capable of running mainline Linux and supported by many partner projects. The BraveHeart Edition was the first publicly-available version of the phone, though it came without a fully functional OS (factory test image) and was geared specifically towards tinkerers and hackers. Its successor is the Community Edition, the first Community Edition started to ship in June 2020. The phone will be available for at least five years.

== First time installation ==

{{Hint|The default PIN for the Manjaro Community Edition is '''123456'''.}}

[[File:PinePhone-3.jpg|400px|thumb|right|PinePhone is capable of running a multitude of different Linux mobile OSes]]

[[File:Pinephone_rendering_blank.png|400px|thumb|right|Rendering of the back and front of PinePhone]]

From the factory the battery has a sticker on it that isolates the battery from the phone. The battery '''will not''' charge until this is removed.

[[File:Pinephone_warning.png|none|left|400px]]

After unboxing remove the back panel using the notch in the corner of the back panel. Then remove the battery and peel off the clear plastic sticker below it that isolates the charging contact. Then replace the battery, see [[PinePhone#Battery|Battery]] for more information.

The SIM card has to be placed in the lower slot, while the microSD has to be placed in the upper slot, as pictured here:

[[File:Pinephone_backside.png|none|left|400px]]

== Specifications ==

'''Dimensions:''' 160.5 x 76.6 x 9.2mm 
'''Weight:''' Between 180-200 grams 
'''SIM Card:''' Micro-SIM 
'''Display:'''
: '''Size:''' 5.95 inches (151mm) diagonal
: '''Type:''' HD IPS capacitive touchscreen, 16M colors
: '''Resolution:''' 1440x720, 18:9 ratio 
'''System on Chip:''' [https://linux-sunxi.org/A64 Allwinner A64] 
'''RAM:''' 2GB or 3GB LPDDR3 SDRAM 
'''Internal Storage:''' 16GB or 32GB eMMC, extendable up to 2TB via microSD, supports SDHC and SDXC 
'''Back Camera:''' Single 5MP, 1/4", LED Flash 
'''Selfie Camera:''' Single 2MP, f/2.8, 1/5" 
'''Sound:''' Loudspeaker, 3.5mm jack & mic (jack doubles as hardware UART if killswitch 6 is deactivated) 
'''Communication: G25-G'''
: '''LTE:''' B1, B2, B3, B4, B5, B7, B8, B12, B13, B18, B19, B20, B25, B26, B28, B38, B39, B40, B41
: '''WCDMA:''' B1, B2, B4, B5, B6, B8, B19
: '''GSM:''' 850, 900, 1800, 1900 (MHz)
: '''WLAN:''' Wi-Fi 802.11 b/g/n, single-band, hotspot
: '''Bluetooth:''' 4.0, A2DP
: '''GNSS:''' GPS/GLONASS/BeiDou/Galileo/QZSS, with A-GPS
'''Sensors:''' Accelerometer, gyro, proximity, ambient light, compass 
'''Killswitches:''' Modem, WiFi & Bluetooth, Microphone, Cameras 
'''Battery:''' Lithium-ion, rated capacity 2800mAh (10.64Wh), typical capacity 3000mAh (11.40Wh) (nominally replaceable with any Samsung J7 form-factor battery) 
'''I/O:''' USB Type-C, USB Host, DisplayPort Alternate Mode output, 15W 5V 3A Quick Charge, follows USB PD specification

== Components ==
{| class="wikitable"
! Component
! Model
|-
| Touchscreen
| Goodix GT917S
|-
| Rear camera
| OmniVision OV5640
|-
| Camera flash
| SGMICRO SGM3140
|-
| Front camera
| GalaxyCore GC2145
|-
| LCD
| Xingbangda XBD599
|-
| WiFi
| Realtek RTL8723CS
|-
| Bluetooth
| Realtek RTL8723CS
|-
| Modem
| Quectel EG25-G
|-
| GNSS/GPS
| Quectel EG25-G
|-
| Magnetometer
| ST LIS3MDL
|-
| Ambient light / Proximity
| SensorTek STK3335
|-
| Sixaxis
| InvenSense MPU-6050
|-
| Vibration motor
| Unknown model
|-
| Notification LED
| LED0603RGB
|-
| Volume buttons
| Buttons connected to the KEYADC
|-
| Power button
| X-Powers AXP803
|-
| Battery fuel gauge
| X-Powers AXP803
|}

See the [[PinePhone_component_list|PinePhone Component List]].

== Hardware revisions ==

# [[Project Anakin]]
# [[Project Don't be evil|"Project Don't Be Evil" devkit]]
# [[PinePhone v1.0 - Dev|PinePhone v1.0 - Developer batch]]
# [[PinePhone v1.1 - Braveheart]]
# [[PinePhone v1.2‎]] - Ubports Community Edition
# [[PinePhone v1.2a]] - postmarketOS Community Edition
# [[PinePhone v1.2b]] - Manjaro Community Edition

== Swapping in a new mainboard revision ==

The mainboard can be replaced, for example for upgrading to a newer hardware revision or if it is faulty. The replacement board does not have an OS preinstalled, to test if everything is working after swapping the mainboard a flashed SD card is required. The mainboard also comes with a non-functional firmware on the ANX chip, a newer firmware version has to be flashed as explained below to get certain USB functionality to work.

=== Replacing the mainboard ===

Prior to replacing your PinePhone’s mainboard please read the steps outlined in bullet points below and watch the attached video.

# You’ll need a small Phillip’s screwdriver and a prying tool to swap out the PinePhone’s mainboard.
# Remove the PinePhone’s back cover. See your quick start guide for details.
# Remove the battery as well as any inserted SD and SIM cards.
# Unscrew all 15 Phillip’s head screws around the midframe of the phone.
# Gently pry up the midframe using a guitar pick or credit card corner. It is easiest to separate the midframe at one of the bottom edges. Work your way around all the sides of the phone until the midframe separates from the phone’s body.
# Detach all ribbon cables and “Lego” connectors. List of things to detach: 1) two “Lego” connects at the bottom of the mainboard. 2) u.FL antenna connect and touchscreen digitizer on PCD left side. 3) LCD ribbon cable top of mainboard, next to audio/ UART jack.
# Pry the mainboard up gently from the left-hand side.
# Remove front and main cameras and reset them into the new mainboard.
# Check that the rubber proximity sensor housing is in the chassis, not stuck to the removed mainboard.
# Place the new mainboard in the chassis, hooking in on the plastic tabs on left side and pressing down firmly on opposite side, and follow the steps (7-2) in reverse. When reattaching the midframe take care that no cables are out of place or trapped, as they may be damaged when tightening screws.

After swapping the mainboard the phone won't boot as there is no OS on the replacement board's eMMC preinstalled. To boot an OS insert a flashed SD card.

A video tutorial can be found here:
[[File:Pinephone_martijn_pcb_replacement.png|thumb|none|600px|link=https://www.youtube.com/watch?v=5GbMoZ_zuZs|Watch Martijn Braam's video tutorial here: https://www.youtube.com/watch?v=5GbMoZ_zuZs. Alternatively user bridadan uploaded a video tutorial of the swap procedure including camera swap and proximity sensor housing here: https://www.youtube.com/watch?v=J3AJEF7akkw.]]

=== Flashing the ANX firmware ===

After swapping the mainboard the ANX chip has to be flashed for full USB functionality.

Download the latest ANX firmware image on the phone:

wget https://xff.cz/git/linux-firmware/plain/anx7688-fw.bin

Execute as root ("sudo su") on the phone:

cp anx7688-fw.bin /lib/firmware/
echo 1 > /sys/class/typec/port0/device/flash_eeprom

== Replacing the screen ==

Before attempting to replace the screen be sure to review "[[Replacing the mainboard]]" since that will get you most of the way there. Be aware that the replacement screen is actually the entire front frame of the phone and there are components that will need to be swapped from your old screen.

* Make sure you have a precision screwdriver set that has the correct size Philips tip. The screws are very small and the heads can easily be stripped if the screwdriver is not correct - if you feel your screwdriver slipping, stop what you are doing and try one that is a better fit. A magnetized screwdriver will help in not losing screws, as will a magnetic parts holder to keep them in while working.

* There are a number of components and cables as well as the insulator sheet under the battery that are glued in place. A hair dryer will loosen the glue and make them much easier to remove. You may want to order extra cables along with the screen just in case.

* The vibrator motor, which is part of the USB-C board assembly and glued into place, will come apart easily and be damaged if you pry it up in the wrong place. Make sure you pry from underneath the complete part, not midway on its housing. The ribbon cable attaching this to the USB-C board is small, thin, and fragile so be careful with that as well.

* The new screen comes with new side switches and insulator sheet but there are a number of parts that need to be transferred from the old screen, like the thin coax cable running up the side, the phone ear speaker, proximity sensor gasket, and a gold-colored mesh glued in place that needs to be transferred to a flexible circuit included on the new screen. If you don't swap over the proximity sensor rubber gasket the screen will immediately turn off after logging in. Be careful when routing the coax cable that it goes around the screw holes or you may drive a screw right through the cable.

Take your time, use the right tools, be careful and you should be rewarded with success.

== Hardware accessory ==

=== PinePhone hardware accessory compatibility ===
See [[PinePhone Hardware Accessory Compatibility]] for a list of devices working with the PinePhone (depending on their OS support).

=== USB-C connector ===

The USB-C can be used to power the device, and offers USB2 host and OTG possibilities, and also can make use of the USB-C capability to integrate HDMI signals. Some USB-C hubs are available that offer power throughput, USB connection, HDMI port and Ethernet connection. The driver that would make this connection available is not supported at this time.

=== Pogo pins ===

The PinePhone has 6 pogo pins on the back allowing for custom hardware extensions such as wireless charging, an IR blaster, a keyboard extension or extended battery case. The pogo pins provide access to an interrupt line, power input to charge the battery, power source and an I2C interface.

[[File:Pinephone pogo.png|none|400px]]

{| class="wikitable"
| Interrupt
| SDA
| SCL
|-
| 5V / VBUS
| VBAT
| GND
|}

The VBUS pin is powered by USB and is 5V. The second power pin is VBAT, which connects to the battery voltage. The I2C and interrupt lines have pull-ups on the phone side. The I2C lines are pulled up to 3V3 by the phone.

For a breakout board see [https://github.com/SMR404/PinephonePogoBreakout here]. For an example project see Martijn's blog post [https://blog.brixit.nl/making-a-backcover-extension-for-the-pinephone/ "Making a backcover extension for the PinePhone"].

=== Back cover ===
A step file for the back cover for creating custom cases is freely available [https://files.pine64.org/doc/PinePhone/PinePhone%20Back%20Cover%20ver%200.5.stp here].

=== Serial console ===

The PinePhone has a serial port in the headphone connector, it's activated by the 6th contact on the dipswitch. If the switch is set to "on", the headphone connector is in audio mode, if it is set to "off" it's in UART mode. The UART serial connection can also be used for communication with other devices from the PinePhone.

The UART is 115200n8.

The pinout for the serial connector is:

* Tip: RX
* Ring: TX
* Sleeve: GND

[[File:PinePhone_Serial_Cable.png|none|400px]]

You can buy a serial debug cable from the [https://pine64.com/product/pinebook-pinephone-pinetab-serial-console/ Pine64 Store]. The store cable uses a 4 ring plug, as seen in the [https://files.pine64.org/doc/pinebook/guide/Pinebook_Earphone_Serial_Console_Developer_Guide.pdf here], but a 3 ring plug works just as well. The cable uses a CH340 chipset based serial to USB converter, but any 3.3v serial connection can be used. Because it is a "host"/DTE it means that you need a ''cross modem cable'' ([https://en.wikipedia.org/wiki/Null_modem Null Modem]) with TX on Tip to be connected to RX. A cable like e.g. [https://www.ftdichip.com/Products/Cables/USBTTLSerial.htm FTDI TTL-232R-3V3-AJ] which has TX on Tip and RX on Ring fits perfectly.

== Killswitch configuration ==

[[File:PinePhone Kill Interruptors de Maquinari del PinePhone 4529.jpg|320px|thumb|right|Detail of DIP switch]]

The PinePhone features six switches that can be used to configure its hardware. They are numbered 1-6, with switch 1 located nearest to the modem. Their "on" position is toward the top of the phone.

{| class="wikitable"
|-
! Number
! Name
! Explanation
! Description
|-
| 1
| Modem
| Pulls Q1501 gate up (FET killing modem power)
| "On" enables 2G/3G/4G communication and GNSS hardware, "off" disables it.
|-
| 2
| WiFi / Bluetooth
| Pulls up CHIP_EN
| "On" enables WiFi and Bluetooth communication hardware, "off" disables it.
|-
| 3
| Microphone
| Breaks microphone bias voltage from the SoC
| "On" enables audio input from on-board microphones (not 3.5mm jack), "off" disables it.
|-
| 4
| Rear camera
| Pulls up PWDN on OV5640
| "On" enables the rear camera, "off" disables it.
|-
| 5
| Front camera
| Pulls up PWDN on GC2145
| "On" enables the front camera, "off" disables it.
|-
| 6
| Headphone
| Pulls up IN2 on analog switch BCT4717ETB
| "On" enables audio input and output via the 3.5mm audio jack, "off" switches the jack to hardware UART mode.
|}

== Camera ==

The PinePhone has two cameras, OmniVision OV5640 with 5MP (up to 2592 x 1944 pixels) as rear camera and GalaxyCore GC2145 with 2MP (up to 1600 x 1200 pixels) as front camera.

[[File:Rose.jpg|400px|thumb|none|Example picture taken on the PinePhone's rear camera by Martijn Braam using his app ''Megapixels''.]]

Further details regarding the camera and the Megapixels camera app can be found on [https://blog.brixit.nl/tag/phones/ Martijn's blog].

== Battery ==

{{Hint|The EG25 modem and RTL8723CS WiFi/bluetooth do not work without battery power, even if you are supplying enough power to the PinePhone with USB-C.}}

The phone ships with a plastic sticker between the battery and the phone. You need to open the back cover (gently), then remove the battery and finally remove the sticker and check that the pins aren't bent. This is to protect the device from turning on during shipping.

The [https://files.pine64.org/doc/datasheet/pinephone/PinePhone%20QZ01%20Battery%20Specification.pdf supplied battery] is [https://forum.pine64.org/showthread.php?tid=8120&pid=53307#pid53307 meant to be] compatible with Samsung part number EB-BJ700BBC / BBE / CBE from the 2015 J7 phone.
* The extended life aftermarket BBU does fit, although it is a tight fit.
* There is [https://forum.pine64.org/showthread.php?tid=8563&pid=55053#pid55053 a report] that the EB-BJ700CBE isn't quite the same size, causing the back not to fit the BraveHeart Edition properly.

The battery terminals, in order from nearest the edge to nearest the middle, are:

# +ve
# thermistor
# -ve
# not connected

The battery includes a protection circuit that isolates it in a number of fault conditions, including if it is discharged too far. The fully discharged battery [https://forum.pine64.org/showthread.php?tid=8563&pid=55377#pid55377 can be recharged] by connecting the phone to a charger. Once it has charged sufficiently you will be able to boot the phone.

If your battery is hard to remove from the phone, try loosening the screws around it. Possibly cutting up a piece of plastic and sliding it under the battery as a pull tab can work too.

<gallery mode="packed", heights=300px>
Image:PinePhone battery1.png|Photo of Brave Heart case from OSAKANA TARO on Twitter
Image:PinePhone battery3.jpeg|Photo of Brave Heart battery sticker from OSAKANA TARO on Twitter
</gallery>

== Modem and carrier support ==
=== APN settings ===

The APN setting is only required for a public Internet connection ("data") on the phone. For tested APN settings and how to apply them see [[PinePhone APN Settings]].

=== Carrier support ===
The page [[PinePhone Carrier Support]] contains information about the frequency support of different carriers and hints on setting up cellular network connectivity.

=== Documents ===

Detailed information about the modem can be found on the [https://xnux.eu/devices/feature/modem-pp.html#toc-modem-on-pinephone page of the developer megi], including reverse-engineered parts of the firmware and its functions. There is also a document about using the modem from January 18th 2020 by megi [https://megous.com/dl/tmp/modem.txt here]. A script at the end of the document showcases a way to poweroff the modem before powering off the phone, which is integrated into most of the available OSes.

=== Firmware modifications ===

See [[PineModems]] for more information regarding modem bootloader unlocking, building a custom modem firmware and modem recovery.

=== Voice mail ===

Some phone operating systems may not have support for accessing your voicemail by holding down the 1 key. If you are in Canada and using rogers or a rogers associated carrier (such as ''Chatr''), you can access your voice mail by calling an external number, see: https://www.howardforums.com/showthread.php/913346-Rogers-GSM-Voicemail-Retrieval-Numbers

In America, AT&T also has support for accessing your voicemail via an external phone number: https://www.att.com/support/article/wireless/KM1009101/

== Operating Systems ==

The PinePhone will automatically boot from microSD if a bootable card is inserted. Although it is technically possible to use any ARM distribution (because the PinePhone uses the mainline kernel), there are a few that are designed specifically for mobile use on devices like the PinePhone.

=== Software releases ===

The [[PinePhone Software Releases]] page has a complete list of currently supported phone-optimized Operating System images that work with the PinePhone as well as other related software information. As soon as more patches get mainlined and distributions ship with the updated kernel, they will also be able to run unmodified on the device.

=== Installation instructions ===

For instructions on how to install the operating systems to the eMMC or SD card see [[PinePhone Installation Instructions]].

=== Flashing eMMC using Jumpdrive ===

[[File:jumpdrive.jpg|400px|thumb|right|Jumpdrive running on the PinePhone]]
The internal eMMC flash storage can be flashed using the Jumpdrive utility by Danct12 and Martijn from postmarketOS.
This utility boots from micro SD and exposes the internal eMMC flash storage when the PinePhone is connected to a computer.
The process of flashing an OS to the exposed and mounted eMMC is identical to that of any other storage medium - e.g. a SD card. You can use the 'DD' command or a utility such as Etcher or Gnome Disks, etc.

Latest Jumpdrive can be found [https://github.com/dreemurrs-embedded/Jumpdrive/releases/ here].

==== Detailed usage instructions ====

# Download the Jumpdrive image
# Flash the Jumpdrive image to a micro SD card
# Boot the PinePhone from the Jumpdrive micro SD card
# Connect the PinePhone to your computer using USB-A -> USB-C cable
# Flash the exposed PinePhone drive (e.g. /dev/mm..., check for the right device in dmesg, GNOME disks, or similar, and make sure it's unmounted) with your chosen OS image
# Once the flashing process is complete, disconnect the PinePhone from your PC, power it down and remove the Jumpdrive SD card
# The process is now finished, and you can boot from eMMC

Jumpdrive also acts as a rescue image in case if you messed up your installation. To do so, you can telnet to '''172.16.42.1''', mount rootfs and fix it!

==== Resize file system ====

If you flash a 4GB image distribution (such as phosh+debian) to your eMMC, your eMMC will only have a 3.7GB partition on it. To use the entire 14.7GB on the eMMC, run the following commands:

# sudo cfdisk /dev/sdX
# Change to [Resize] in the ncurses program, resize the 3.7GB partition to 14.7GB, and [Write]
# sudo resize2fs /dev/sdXY

Replace X with your drive's name. Replace Y with the partition you resized in cfdisk.

==== Feedback ====

If you've found an issue or want to improve the tool consider these sites:

* Issues: https://github.com/dreemurrs-embedded/Jumpdrive/issues
* Pull Requests: https://github.com/dreemurrs-embedded/Jumpdrive/pulls

== Frequently asked questions ==

For a list of frequently asked questions (including information regarding the shipping) see [[PinePhone FAQ]].

== Press ==

For an overview about media of the PinePhone you can use for the news, blogs, or similar see [[PinePhone Press]].

== PinePhone board information, schematics and certifications ==
* PinePhone mainboard schematic:
** [https://files.pine64.org/doc/PinePhone/PinePhone%20v1.2b%20Released%20Schematic.pdf PinePhone mainboard Released Schematic ver 1.2b]
** [https://files.pine64.org/doc/PinePhone/PinePhone%20v1.2a%20Released%20Schematic.pdf PinePhone mainboard Released Schematic ver 1.2a]
** [https://files.pine64.org/doc/PinePhone/PinePhone%20v1.2%20Released%20Schematic.pdf PinePhone mainboard Released Schematic ver 1.2]
** [[PinePhone_v1.2|PinePhone schematic ver 1.2 change list]]
** [https://files.pine64.org/doc/PinePhone/PinePhone%20Schematic%20v1.1%2020191031.pdf "Braveheart" PinePhone mainboard Schematic ver 1.1]
** [https://files.pine64.org/doc/PinePhone/PinePhone%20mainboard%20top%20placement%20v1.1%2020191031.pdf "Braveheart" PinePhone mainboard component top placement drawing ver 1.1]
** [https://files.pine64.org/doc/PinePhone/PinePhone%20mainboard%20bottom%20placement%20v1.1%2020191031.pdf "Braveheart" PinePhone mainboard component bottom placement drawing ver 1.1]
* PinePhone USB-C small board schematic:
** [https://files.pine64.org/doc/PinePhone/PinePhone%20USB-C%20small%20board%20schematic%20v1.0%2020190730.pdf PinePhone USB-C small board Schematic ver 1.0]
** [https://files.pine64.org/doc/PinePhone/PinePhone%20USB-C%20small%20board%20top%20placement%20v1.0%2020190730.pdf PinePhone USB-C small board component top placement drawing ver 1.0]
** [https://files.pine64.org/doc/PinePhone/PinePhone%20USB-C%20small%20board%20bottom%20placement%20v1.0%2020190730.pdf PinePhone USB-C small board component bottom placement drawing ver 1.0]
* PinePhone certifications:
** [https://files.pine64.org/doc/cert/PinePhone%20FCC%20SDOC%20Certificate-S19112602605001.pdf PinePhone FCC Certificate]
** [https://fcc.report/FCC-ID/2AWAG-PINEPHONE RF Exposure SAR Information from FCC ID site]
** [https://files.pine64.org/doc/cert/PinePhone%20CE%20RED%20Certificate-S19112602602.pdf PinePhone CE RED Certificate]
** [https://files.pine64.org/doc/cert/PinePhone%20ROHS%20Report.pdf PinePhone ROHS Report]
** PinePhone's GSMA TAC (Type Allocation Code) is 86769804

== Datasheets for components and peripherals ==

* Allwinner A64 SoC information:
** [https://files.pine64.org/doc/datasheet/pine64/A64%20brief%20v1.0%2020150323.pdf Allwinner A64 SoC brief introduction]
** [https://files.pine64.org/doc/datasheet/pine64/A64_Datasheet_V1.1.pdf Allwinner A64 SoC Data Sheet V1.1 (Official Released Version)]
** [https://files.pine64.org/doc/datasheet/pine64/Allwinner_A64_User_Manual_V1.0.pdf Allwinner A64 SoC User Manual V1.0 (Official Release Version)]

* X-Powers AXP803 PMU (Power Management Unit) information:
** [https://files.pine64.org/doc/datasheet/pine64/AXP803_Datasheet_V1.0.pdf AXP803 PMIC datasheet]

* LPDDR3 (178 Balls) SDRAM:
** [https://files.pine64.org/doc/datasheet/pinephone/ATL3A1632H12A_mobile_lpddr3_11x11.5_v1.0_1600.pdf Artmem LPDDR3 datasheet]

* eMMC information:
** [https://files.pine64.org/doc/datasheet/pinephone/Kimtigo_fbga153_16_32_64_eMMC_datasheet_v1.3.pdf Kimtigo eMMC datasheet]

* CMOS camera module information:
** [https://files.pine64.org/doc/datasheet/pinephone/QZ01-rear-2019-0717(HW)%20Model.pdf PinePhone 5M Pixel Real CMOS Image Sensor Module]
** [https://files.pine64.org/doc/datasheet/pinephone/OV5640_datasheet.pdf OV5640 5MP CMOS Image Sensor SoC for Rear Module datasheet]
** [https://files.pine64.org/doc/datasheet/pinephone/QZ01-front-2019-0717(HW)%20Model.pdf PinePhone 2M Pixel Front CMOS Image Sensor Module]
** [https://files.pine64.org/doc/datasheet/pinephone/GC2145%20CSP%20DataSheet%20release%20V1.0_20131201.pdf GC2145 2MP CMOS Image Sensor SoC for Front Module datasheet]

* LCD touch screen panel information:
** [https://files.pine64.org/doc/datasheet/pinephone/PinePhone%20LCD-QZ01.pdf 5.99" 1440x720 LCD IPS Panel specification]
** [https://files.pine64.org/doc/datasheet/pinephone/ST7703_DS_v01_20160128.pdf ST7703 LCD Controller datasheet]
** [https://files.pine64.org/doc/datasheet/pinephone/GT917S-Datasheet.pdf GOODiX GT917S Capacitive Touch Controller datasheet]

* Lithium battery information:
** [https://files.pine64.org/doc/datasheet/pinephone/PinePhone%20QZ01%20Battery%20Specification.pdf PinePhone Lithium Battery specification]
** [https://files.pine64.org/doc/datasheet/pinephone/PinePhone%20QZ01%20Battery%20ZCV%20Curve%20Chart.xlsx PinePhone Lithium Battery ZCV curve chart]

* WiFi/BT module information:
** [https://files.pine64.org/doc/datasheet/pine64/RTL8723BS.pdf RTL8723BS/RTL8723CS specification]

* LTE module information:
** [https://www.quectel.com/UploadFile/Product/Quectel_EG25-G_LTE_Standard_Specification_V1.2.pdf Quectel EG25-G LTE Module specification v1.2]
** [[Media:Quectel EC25EC21 AT Commands Manual V1.2.pdf|EC25&EC21 AT Commands Manual]]
** [https://www.quectel.com/UploadImage/Downlad/Quectel_EC2x&EG25-G&EG9x&EM05_FILE_AT_Commands_Manual_V1.0.pdf Quectel EC2x EG25-G EG9x EM05 FILE AT Commands Manual v1.0]
** [https://sixfab.com/wp-content/uploads/2018/09/Quectel_EC25EC21_GNSS_AT_Commands_Manual_V1.1.pdf Quectel EC25 EC21 GNSS AT Commands Manual v1.1]

* Sensors:
** [https://www.st.com/en/mems-and-sensors/lis3mdl.html ST LIS3MDL 3-axis Magnetomater Datasheet]
** [https://www.invensense.com/products/motion-tracking/6-axis/mpu-6050/ InvenSense MPU-6050 Six-Axis (Gyro + Accelerometer) MEMS datasheet]
** [https://www.sensortek.com.tw/en/product/Proximity_Sensor_with_ALS.html SensorTek STK3335 Ambient Light Sensor and Proximity Sensor]

* Digital video to USB-C bridge:
** [https://www.analogix.com/en/system/files/AA-002281-PB-6-ANX7688_Product_Brief.pdf ANX7688 product brief]

* Case information:
** [https://files.pine64.org/doc/datasheet/pinephone/PinePhone%20Exploded%20Diagram%20ver%201.0.pdf PinePhone case exploded diagram]
** [https://files.pine64.org/doc/datasheet/pinephone/PinePhone%20Back%20Cover.stp PinePhone back cover 3D file]

* Other components:
** See links in the [[PinePhone_component_list|Component List]]

== Developer works ==
=== Megous ===

* [https://xnux.eu/howtos/pine64-pinephone-getting-started.html Getting start with PinePhone Hardware]
* [https://xnux.eu/devices/pine64-pinephone.html State of development progress]
* [https://xnux.eu/news.html PinePhone Technical News and Update, also applies to other Allwinner devices including PINE A64 SBC]
* [https://xnux.eu/contribute.html Contributions to the kernel development]

== External links ==
* [https://pine64.com/product-category/pinephone/ The PinePhone on the official Pine store]
* [https://pine64.com/product-category/smarphone-spare-parts/ PinePhone spare parts on the official Pine store]
* [https://pine64.com/product-category/smartphone-accessories/ PinePhone accessories on the official Pine store]

[[Category:PinePhone]] [[Category:Allwinner A64]]