Pinebook Pro Hardware Accessory Compatibility

2020-02-01T02:13:18Z

Thecakeisnaoh: Added Corsair MP300 power states

= Pinebook Pro accessories - by type =

This page was started in the early days when not all accessories/peripherals have been working

== NVMe SSD drives ==
Note that only PCIe type M.2 drives will work. Any SATA or USB type M.2 card will NOT work.
{| class="wikitable sortable"
!Type || Make/Model || Size || Hardware IDs || Result || Notes || Power options Active only || Save power setting?
|-
| 2242 || Toshiba OCZ RC 100 || 240 GB || RC100-M22242-240G || good || || ||
|-
| 2242 || Lexar NM520 || 256 GB || LNM520-256RBNA || good || || PS 0: 3.05W PS 1: 2.44W PS 2: 2.02W || No. See [https://forum.pine64.org/showthread.php?tid=8737&pid=56481#pid56481 workaround].
|-
| 2280 || XPS SX8200 || 512 GB || ASX8200PNP-512GT-C || good || Performed [https://forum.pine64.org/showthread.php?tid=8322 these] steps for physical installation. Currently rooting from drive. || ||
|-
| 2280 || Intel 660p M.2 || 512 GB || SSDPEKNW512G8X1 || good || || ||
|-
| 2280 || Intel 660p M.2 || 1 TB || SSDPEKNW010T8X1 || good || || PS 0: 4.00W PS 1: 3.00W PS 2: 2.20W APSTE Disabled by default || N/A
|-
| 2280 || Samsung 970 EVO Plus || 250 GB || MZ-V7S250BW || fail || Tested on Manjaro-ARM as root drive. Limited to PS 2 and Volatile Write Cache off gives the most stable results, but it will still hang on a hdparm test. || ||
|-
| 2280 || Samsung 970 EVO Plus || 500 GB || MZ-V7S500 || fail || too power hungry? || PS 0: 6.2W PS 1: 4.3W PS 2: 2.1W ||
|-
| 2280 || Samsung 970 EVO || 1 TB || MZ-V7E1T0BW || fail || too power hungry? || ||
|-
| 2280 || Corsair MP300 || 120 GB || CSSD-F120GBMP300 || || || PS 0: 3.00W PS 1: 2.00W PS 2: 2.00W PS 3: 0.1W PS 4: 0.005W APSTE Disabled by default ||
|-
| 2280 || Silicon Power P34A60 || 256 GB || ??? || fail || Isn't detected || ||
|-
| 2280 || Sabrent Rocket || 256 GB || SB-ROCKET-256 || good || || || no
|-
| 2242 || Sabrent Rocket Nano || 512 GB || SB-1342-512 || good || No touchpad issues, didn't trim NVME adapter board. (Might be too power hungry. More testing needed.) || ||
|-
| 2280 || MyDigitalSSD SBXe || 960 GB || || good || || APST enabled Power states N/A || N/A
|-
| 2280 || HP SSD EX900 || 250GB || || good || no low-power modes available || ||
|-
| 2280 || WD BLUE SN550 || 1TB || WDC WDS100T2B0C-00PXH0 || good || Successed for boot from NVMe (Bionic MATE) || PS 0: 3.50W PS 1: 2.70W PS 2: 1.90W APSTE Disabled by default || N/A
|-
| 2280 || WD Blue SN500 || 500GB || WDS500G1B0C || bad || Works OK on power state 2 (2.5W), but hangs the system whenever there is intense IO (peak draw) on the drive || ||
|-
| 2242 || WD PC SN520 || 256GB || - || bad || Power LED Flashes. Nothing else happens. || ||
|-
|2280 || WD BLACK SN750 || 250GB || WDS250G3X0C-00SJG0 || good || No touchpad issues, didn't trim NVME adapter board. || APSTE disabled by default PS 0: 5.00W PS 1: 3.50W PS 2: 3.00W ||
|-
| 2242 || KingSpec NE-512 || 512 GB || NE512 || good || || APST enabled Power states N/A || N/A
|
|}

== USB hardware ==
{| class="wikitable sortable"
!Type || Make/Model || Hardware IDs || Result || Notes
|-
|USB-2 SDHC reader || Sandisk MobileMate+ || 0781:b2b3 || good ||
|-
|USB-3 SDHC/CF reader || Transcend TS-RDF8K || 8564:4000 || good ||
|-
|USB-3 combo hub (network, card slots, usb ports) || generic || 05e3:0610 hub, 0bda:8153 gigE, 05e3:0743 card reader || network good, usb ports good, card reader good ||
|-
|USB-C combo hub (network, card slots, usb ports) || generic || 05e3:0612 hub, 0bda:8153 realtek gigE || network good, usb ports bad, card reader bad ||
|-
|5-1 USB-C hub || [https://www.aliexpress.com/item/32954358411.html from aliexpress] || 05e3:0626 hub || HDMI, Network, USB-3, USB-C PD [http://www.sympato.ch/~dryak/files/usbc-dock.jpg work] || might need changing orientation or USB-C cable
|-
|Yubikey original || Yubico || 1050:0010 || good ||
|-
|4 Port USB 3 NIC || Delock 62966 || || All good || 4 individually controllable Gigabit Ethernet Ports. Consider using it with own power supply
|-
|USB-2 Fast Ethernet adapter || Realtek RTL8152 || 0bda:8152 || good ||
|-
|USB 3 to Gigabit Ethernet Adapter || Pluggable USB 3.0 to Ethernet Gigabit (ASIX AX88179 chipset) || 0b95:1790 || good ||
|}

== USB C alternate mode DP ==
Note that only USB C alternate mode Display Port will pass video. Any HDMI, DVI or VGA port must be converted internally by the device from Display Port. Or the device won't work for video.
{| class="wikitable sortable"
!Type || Make/Model || Hardware IDs || Result || Notes
|-
|USB-C to HDMI adapter 201018 || Cable Matters || || good || tested to 1080p30, audio works
|-
|USB-C to HDMI adapter || generic || || good || tested to 4k60
|-
|USB-C to DP Adapter || OrxnQ || || good || Upto 4K@60Hz, tested to 1080p
|-
|USB-C HDMI adapter (DP-alt mode) || QGeeM || || Good || Manjaro 2020-01-25
|-
|USB-C combo hub (HDMI, network, card slots, USB ports) || generic || || all bad ||
|-
|USB-C combo hub (HDMI, VGA, Ethernet, card slots, USB 2 & 3 || Powlaken || 05e3:0610 0bda:8153 || USB, Power, Ethernet and SD good, HDMI and VGA don't work ||
|-
|USB-C Dock (HDMI, VGA, Ethernet, microSD/SD card slots, 2 USB 3 Ports, 1 USB-C Port, USB-Power Passthru || Digitus DA-70865 || || USB, Ethernet and MicroSD/SD good, video crashes System. || Tested on Manjaro w/ Kernel 5.5. You have to turn the USB-C connector upside down for it to work. Video seems to be a driver issue.
|-
|USB-C Dock (HDMI, VGA, Ethernet, microSD/SD card slots, 2 USB 3 Ports, 1 USB-C Port, USB-Power pass-through) || generic || || Ethernet and MicroSD/SD good, USB bad, video up to 1080p. || https://forum.pine64.org/showthread.php?tid=8728
|-
|USB-C Dock (DP, HDMI, 1Gbps Ethernet, SD card slot, 2 USB 3 Ports, USB-C power in port || goFanco || || DP, Ethernet & USB working, (HDMI & SD card un-tested). Video tested to 1080p || Tested on default Debian
|-
|USB-C Dock (HDMI, USB 3.0 x 2, USB-C PD Pass Thru Power Port Up to 100W, SD/TF Card Reader || Hiearcool 7-in-1 || || HDMI, USB, Power Port OK, SD/TF Reader=No || Default Debian
|-
|USB-C 3.0 Multi-Port Hub (HDMI, USB 3.0 x 1, USB-C charge only) || Linden LITCAD17 || || HDMI OK, USB OK, Power Port NO || Default Debian & ayufan Ubuntu
|-
|USB-C to DP adapter || Nekteck || 04b4:5210 || good || Shows up as "Cypress Semiconductor Corp. Billboard Device" in lsusb and dmesg output. Works in latest Manjaro (as of January 26, 2020) with no issues.
|}

== Other hardware ==
{| class="wikitable sortable"
!Type || Make/Model || Hardware IDs || Result || Notes
|-
|Bluetooth Mouse || HP Z5000 || E5C13AA || good ||
|-
|Bluetooth Mouse || Logitech Triathlon M720 || || good ||
|-
|Bluetooth Mouse || Logitech Ultra-Thin Touch Mouse || || good || detects battery level as "keyboard"
|-
|Bluetooth Mouse || Logitech MX Anywhere 2 || || good ||
|-
|Bluetooth Mouse || Logitech M535 || 910-004432 || good ||
|-
|Bluetooth Mouse || Microsoft Bluetooth Mouse || RJN-00002 || good ||
|-
|Bluetooth Mouse || Fenifox low profile || MX106-Black || good ||
|-
|Bluetooth Speaker || Ivation Acoustix || || good || audio sink profile
|-
|Headphone || Sony WH-1000XM2 || || just tested playback, good || Needs pulseaudio-module-bluetooth
|-
|[https://www.aliexpress.com/item/32831647303.html USB charging cable] || - || - || charges || got the cable a while back so may not be identical to current product
|-
|USB Audio & Bluetooth Headset || Sony SBH90C || || good || Works well connected via USB Type-C and Bluetooth.
|-
|SD Card || Samsung Evo Select 512GB || MB-ME512GA/AM || good ||
|-
|SD Card || Samsung Evo Plus 64GB || || good || hdparm tested 44MBps read speads
|-
|SD Card || Sandisk Ultra 400GB || || good || Works fine as a storage extension. Mounted for pictures, etc.
|-
|}

PINE64 - User contributions [en]

Pinebook Pro Hardware Accessory Compatibility